Français dropdown-ico

Manuel d’utilisation Delta 31-250

24 pages 3.48 mb
Télécharger

Aller à la page of 24

Summary
  • Delta 31-250 - page 1

    INSTRUCTION MANUAL 18" x 36" Drum Sander (Models 31-250, 31-255X) P ART NO. 406-13-651-0021 - 06-19-03 Copyright © 2003 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). ...

  • Delta 31-250 - page 2

    2 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury . Used without the saf ...

  • Delta 31-250 - page 3

    3 F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJUR Y . 1. FOR YOUR OWN SAFETY , READ THE INSTRUC- TION MANUAL BEFORE OPERA TING THE MACHINE. Learning the machine’ s application, limitations, and specific hazards will gr eatly minimize the possibility of accidents and injury . 2. USE CERTIFIED SAFETY EQUIPMENT . Eye protection ...

  • Delta 31-250 - page 4

    4 F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJUR Y . ADDITIONAL SAFETY RULES FOR DRUM SANDERS SA VE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. 1. DO NOT OPERA TE THIS TOOL UNTIL it is assembled and installed according to the instructions. 2. OBT AIN ADVICE from your supervisor, instructor , or an ...

  • Delta 31-250 - page 5

    5 A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cor ds which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s plug. Before connec ...

  • Delta 31-250 - page 6

    6 Use proper extension cor ds. Make sure your extension cor d is in good condition and is a 3-wire extension cord which has a 3-pr ong grounding type plug and matching r eceptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine. An undersized cord will cause ...

  • Delta 31-250 - page 7

    7 CAUTION T AG CAUTION: Pay close attention to caution tags attached to this machine and follow these instructions precisely . This machine is heavy . Remove the container from ar ound the machine. DO NOT lift it from the container . Carefully unpack all loose items fr om the shipping container and cut the carton from ar ound the machine. CAR TON C ...

  • Delta 31-250 - page 8

    8 A TT ACHING LEGS This machine is heavy . Use two or more people when lifting. 1. With the machine on its back, resting on the two wood blocks (not supplied), attach the legs. (Fig. 1). NOTE: The legs are universal but the mounting hole pattern is different fr ont to rear . See (A) Fig. 2A and Fig. 2B. 2. Attach the leg that goes under the motor f ...

  • Delta 31-250 - page 9

    9 Fig. 7 A TT ACHING THICKNESS SCALE 1. Remove screw and washer (A) Fig. 7. 2. Place thickness scale (B) Fig. 8 over the hole and replace screw and washer (A). 3. Loosen screw (C) Fig. 9, and position pointer against scale (B) Fig. 9. Tighten screw (C) Fig. 9. IMPORT ANT : Refer to section “CHECKING AND ADJUSTING T ABLE HEIGHT” in this manual f ...

  • Delta 31-250 - page 10

    10 OPERA TING CONTROLS AND ADJUSTMENTS Fig. 12 Fig. 13 Fig. 15 B A B C B ST ARTING AND STOPPING THE MACHINE 1. The drum motor on/off switch (A) Fig. 12 is located underneath the switch shield (B). T o turn the drum “ON”, move switch (A) to the “ON” (up) position. 2. T o turn the drum “OFF”, push down on switch shield (B) Fig. 13. NOTE: ...

  • Delta 31-250 - page 11

    11 CHECKING AND ADJUSTING FEED BEL T TRACKING AND TENSION IMPORT ANT : READ THIS COMPLETE SECTION BEFORE MAKING ANY ADJUSTMENTS TO BEL T TRACKING OR TENSION. TRACKING DISCONNECT MACHINE FROM POWER SOURCE. IMPORT ANT : The feed belt runs slowly , therefor e response time to adjustments may also be slow . T ake your time. 1. The tracking and tensioni ...

  • Delta 31-250 - page 12

    12 Fig. 22 1. Run a piece of lumber through the drum sander (Fig. 22) to finish one side of the boar d. 2. Use a square (A) Fig. 23 to measur e the thickness of the lumber . 3. Loosen the screw (B) Fig. 24. Move scale up or down until the cursor shows the exact boar d thickness that was measured in STEP 2 . Tighten the scr ew . SETTING THE HEIGHT S ...

  • Delta 31-250 - page 13

    3. Use a 9/16” socket with an extension (not supplied). Place it in one of the two holes where the hole plugs wer e removed. Loosen one hex bolt, then the other to r elieve tension on the motor . (One is shown at (D) Fig. 26). Apply upward pr essure on the motor (located under the machine) to relieve tension on the belt. Replace or change the bel ...

  • Delta 31-250 - page 14

    14 DUST COLLECTION The drum cover has a 4” O.D. dust chute (A) Fig. 35 that connects to a dust collection system. NEVER OPERA TE THIS MACHINE WITHOUT FIRST CONNECTING IT TO A DUST COLLECTION SYSTEM. It is recommended that a dust collection system be used with at least 400 to 600 CFM capacity . Attach a 4" hose to the hood, or attach an acces ...

  • Delta 31-250 - page 15

    15 WHA T F ACTORS AFFECT SANDING OPERA TIONS? A. SANDING BEL T GRIT 1. 36 grit – Used for very aggressive stock r emoval, glue removal, or for sanding r ough boards. Leaves a r ough finish. 2. 60 grit – Used for heavy stock removal and r ough surfaces, and for truing warped material. Leaves a rough finish. 3. 80 grit – Used for general purpos ...

  • Delta 31-250 - page 16

    16 WHA T CAUSES BURN MARKS Burning the wood can be caused by several things. W e suggest checking for; sanding belt overlap on the drum wrap, sanding paper loading up, too much stock removal with too fine a grit paper , too slow a feed rate, and dull or worn sand paper . WHEN DO I MAKE T ABLE HEIGHT ADJUSTMENTS FOR MA TERIAL REMOV AL? Locate the ha ...

  • Delta 31-250 - page 17

    17 HOW DO I SAND GLUED BOARDS? 1. Glue the boards as flat as possible at the outset. 2. Remove excess glue from the top and bottom befor e it dries. 3. Use a coarse belt for initial stock removal (36 to 60 grit). 4. Run the board at dif ferent locations over the entir e length of the drum to prevent glue build-up on the sanding belt. 5. After glued ...

  • Delta 31-250 - page 18

    18 STEP 1 - TENSION ON TIMING BEL T 1. The timing belt should be checked for the correct tension. If the belt is too tight, the table will be difficult to move. A loose timing belt may cause the belt to jump a tooth on the timing gear . Deflection in the middle of the long span should be 2 - 3 lbs to deflect the belt to the outside frame wall. 2. T ...

  • Delta 31-250 - page 19

    19 from turning and tighten the socket head screw(B) with the 3/16" hex wrench. 4. With the support plate level, try moving the table up and down. 5. If the movement is still tight, go back through this procedur e before going to the next step of CHECKING LOCK NUT ADJUSTMENT . STEP 3 - CHECKING LOCK NUT ADJUSTMENT 1. At the base of three of th ...

  • Delta 31-250 - page 20

    20 MAINTENANCE MAKE CERT AIN THE MACHINE IS DISCONNECTED FROM THE POWER SOURCE BEFORE PERFORMING MAINTENANCE PROCEDURES. 1. Periodically clean or vacuum the feed belt. 2. Periodically clean the sawdust from sanding cylinder cavities. BRUSH INSPECTION AND REPLACEMENT CAUTION: BEFORE INSPECTING BRUSHES, DISCONNECT THE MACHINE FROM THE POWER SOURCE. F ...

  • Delta 31-250 - page 21

    21 NOTES ...

  • Delta 31-250 - page 22

    22 NOTES ...

  • Delta 31-250 - page 23

    23 P AR TS, SERVICE OR WARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standards and ar e serviced by a network of Porter -Cable • Delta Factory Service Centers and Delta Authorized Service Stations. T o obtain additional information regar ding your Delta quality product or to obtain parts, service, warra ...

  • Delta 31-250 - page 24

    The following are trademarks of POR TER-CABLE · DEL T A (Las siguientes son marcas registradas de POR TER-CABLE S.A.): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T ACRAFT ® , DEL T AGRAM™, Delta Series 2000™, DURA TRONIC™, Emc²™, FLEX ® , Flying Chips? ...

Fabricant Delta Catégorie Sander

Les documents que nous recevons du fabricant de l'appareilDelta 31-250 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Delta
- manuels d’utilisations 31-250
- fiches produit Delta
- dépliants
- ou étiquettes-énergie Delta 31-250
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Delta 31-250.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Delta 31-250, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Delta 31-250. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Delta 31-250.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Delta 31-250, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Delta 31-250 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Delta 31-250.

Le manuel d’utilisation complet Delta, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Delta 31-250 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Delta 31-250, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lDelta 31-250 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Delta 31-250 - qui devraient nous aider dans les premières étapes lors de l'utilisation Delta 31-250
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Delta 31-250
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Delta 31-250 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Delta 31-250?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Delta 31-250, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Delta 31-250 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)