-
APC 2000 - page 1
Smart-UPS ® Models 900, 1250 and 2000 User's User's User's User's User's Manual Manual Manual Manual Manual TM ...
-
APC 2000 - page 2
Important safety instructions! Please r ead this manual! V euillez lir e ce manuel! Bitte lesen Sie dieses Anleitungshandbuch! ¡Se ruega leer este manual de instrucciones! This manual provides safety, installation and operating instructions that will help you derive the fullest performance and service life that the UPS has to offer. PLEASE SAVE TH ...
-
APC 2000 - page 3
Page 1 T able of contents 1. 0 Intr oduction ...................................................................... 2 2. 0 Safety! .............................................................................. 4 Sécurité! (Français) ............................................................................................... 5 Sicherheit! (Deu ...
-
APC 2000 - page 4
Page 2 1.0 Intr oduction 1.1 Over view This equipment is a high performance line interactive uninterr uptible power source (UPS) designed to provide clean, r eliable AC power to computer loads. The UPS's line interactive cir cuit topology , illustrated below , of fers excellent ef ficiency , on-line voltage regulation and fast utility fault r ...
-
APC 2000 - page 5
Page 3 1.0 Intr oduction 1.2 SmartBoost SmartBoost allows continuous on-line operation during extended brownouts or low line voltage conditions. The UPS compensates for the r educed line voltage by boosting the load voltage to a value 12% above the input. Reliability is enhanced because the limited battery capacity is saved for complete utility fai ...
-
APC 2000 - page 6
Page 4 2.0 Safety ! Caution! CAUTION ! ■ T o r educe the risk of electric shock, disconnect the Uninterr uptible Power Source from the mains before installing computer interface signal cable (when used). Reconnect the power cord only after all signalling inter connections have been made. ■ Connect the Uninterr uptible Power Source to a two-pole ...
-
APC 2000 - page 7
Page 5 2.0 Sécurité ! Attention! A TTENTION! ■ Pour réduir e le risque d’électrocution, débranchez la prise principale de la sour ce d’alimentation permanente (Uninterr uptible Power Source), avant d’installer le câble d’interface allant à l’ordinateur (si utilisé). Ne r ebranchez le bloc d’alimentation qu’après avoir effec ...
-
APC 2000 - page 8
Page 6 2.0 Sicherheit ! V orsicht! VORSICHT! ■ Um die Gefahr eines elektrischen Schlages auf ein Minimum zu r eduzier en, die unterbrechungsfr eie Stromversor gung vom Str omnetz trennen, bevor ggf. ein Com- puter -Schnittstellensignalkabel angeschlossen wir d. Das Netzkabel erst nach Herstellung aller Signalverbindungen wieder einstecken. ■ Di ...
-
APC 2000 - page 9
Page 7 ESP AÑOL 2.0 ¡ Seguridad ! ¡Atencion! ¡ATENCION! ■ Para r educir el riesgo de descarga eléctrica, desconecte de la r ed la Fuente de energía ininterrumpible antes de instalar el cable de señalización de interfaz de la computadora (si se usa). V uelva a conectar el conductor flexible de alimentación solamente una vez efectuadas tod ...
-
APC 2000 - page 10
Page 8 3.0 Pr esentation 3.1 900V A and 1250V A models - 100, 120 V ac versions Rear view Fr ont view Site wiring fault light See section 4.6 . UPS enable switch See section 4.4 . Circuit breaker NEMA 5-15R receptacles On / Test / Alarm disable pushbutton See section 5.1 . Display features See section 5.0 . Power standby pushbutton See section 5.1 ...
-
APC 2000 - page 11
Page 9 3.0 Pr esentation 3.2 900V A and 1250V A models - 220/230/240 V ac version Rear view Fr ont view On / Test / Alarm disable pushbutton See section 5.1 . Display features See section 5.0 . Power standby pushbutton See section 5.1 . IEC 320 output couplers All couplers are protected by the UPS. IEC 320 inlet Computer interface port See section ...
-
APC 2000 - page 12
Page 10 3.0 Pr esentation 3.3 2000V A model - 100, 120 V ac versions Fr ont view Rear view Power standby pushbutton See section 5.1 . On / Test / Alarm disable pushbutton See section 5.1 . Battery pack Electronics enclosure 15Amp circuit breaker protects center receptacles NEMA 5-15R receptacles Battery pack cables Display features See section 5.0 ...
-
APC 2000 - page 13
Page 11 3.0 Pr esentation 3.4 2000V A model - 120 V ac versions options The -1, -2 and -4 wiring device options for the 120 V ac version 2000V A model UPS are shown below for r efer ence. These options allow simple plug-in installation of the UPS where special service or load wiring devices ar e used. Note: Option -3 has been r eplaced by an impr o ...
-
APC 2000 - page 14
Page 12 3.0 Pr esentation 3.5 2000V A model - 208 V ac version and options The standar d 208 V ac version 2000V A model UPS and its wiring device options are shown below for r efer ence. These options allow simple plug-in installation of the UPS where special service or load wiring devices ar e used. Standar d Option -1 Option -2 3.5.1 Standar d 20 ...
-
APC 2000 - page 15
Page 13 3.0 Pr esentation 3.6 2000V A model - 220/230/240 V ac version Power standby pushbutton See section 5.1 . Battery pack Electronics enclosure Battery pack cables Rear view Fr ont view On / Test / Alarm disable pushbutton See section 5.1 . IEC 320 output couplers All couplers are protected by the UPS. IEC 320 inlet Display features See sectio ...
-
APC 2000 - page 16
Page 14 4.0 Installation 4.1 Receiving inspection Once the UPS has been r emoved from its shipping container , it should be inspected for damage that may have occurr ed while in transit. Immediately notify the carrier and place of pur chase if any damage is found. The packing materials ar e made from recyclable materials and should be saved for r e ...
-
APC 2000 - page 17
Page 15 4.0 Installation 4.3 Connect battery pack - 2000V A model only Follow the instructions listed below to install and lock the battery pack coupler . Note: Use only factory supplied or authorized battery packs! 4.3.1 Use a phillips screwdriver to r emove the battery coupler clamp from the electronics enclosur e. 4.3.2 T urn the battery coupler ...
-
APC 2000 - page 18
Page 16 4.0 Installation 4.4 Connect UPS to service and enable - continued ■ 220/230/240 V ac versions The 220/230/240 V ac version UPS is not furnished with an input line cord. Instead, two output cor ds are supplied. However , in most installations it will not be necessary to purchase a UPS input power cord. Simply swap the line cor ds from you ...
-
APC 2000 - page 19
Page 17 4.0 Installation 4.5 Plug loads into UPS Plug all loads to be protected into the UPS. Do not exceed the UPS's capacity as given in section 9.0 . Once switched on, the UPS will monitor and display the magnitude of the applied load. Note: Do not plug laser printers into this UPS. Laser printers draw a considerable amount of power . This ...
-
APC 2000 - page 20
Page 18 5.0 Operation 5.1 Display featur es 5.1.1 On / T est / Alarm disable pushbutton The On / T est / Alarm disable pushbutton is used to contr ol activation of the UPS and to energize the load. Once the UPS is ener gized, pressing the button will initiate a battery test. This will for ce the UPS to operate on-battery for a brief time during whi ...
-
APC 2000 - page 21
Page 19 5.0 Operation 5.2 Battery capacity bar graph The battery capacity bar graph continuously displays the state of battery charge. In the above example, the display shows that 100% of rated battery capacity is available. Wher e power quality is fair , the UPS will be able to maintain the battery at 100% of rated capacity . In the event of an ex ...
-
APC 2000 - page 22
Page 20 5.0 Operation 5.4 Line voltage bar graph The line voltage bar graph displays the UPS's input voltage in discr ete steps. Line voltage is displayed when the I/T es t pushbutton is pr essed and held. The example above shows that the UPS's input line voltage is between 1 16 and 123 V ac (120 V a c version UPS, see table for values fo ...
-
APC 2000 - page 23
Page 21 5.0 Operation Note: Option switches may be thrown at any time and take effect immediately . 5.5.3 Replace battery In the event the UPS's battery fails a battery test, the UPS will emit "chirps" for a period of 1 minute. If the UPS is left operating while in this condition, the UPS will emits chirps once every 5 hours until a ...
-
APC 2000 - page 24
Page 22 5.0 Operation 5.6 Option switches - continued 5.6.2 Option switch 2 Option switch 2 controls differ ent functions depending upon the UPS version type. The switch contr ols no functions on 100 V ac and 208 V ac version UPSs. ■ 120 V ac version The UPS's factory set input voltage limits for on-line and SmartBoost operation are given in ...
-
APC 2000 - page 25
Page 23 5.0 Operation 5.7 Extended capabilities The following sections briefly describe the UPS’s extended capabilities. These ad- vanced functions are accessed by a computer running optional PowerDoctor or PowerChute plus UPS monitoring softwar e. See the UPS monitoring software literature for mor e information on the application of these functi ...
-
APC 2000 - page 26
Page 24 5.0 Operation 5.7 Extended capabilities - continued ● Output voltage, internal temperature, battery voltage, battery capacity - The UPS continuously monitors the rms output voltage, internal temperatur e in degr ees Celsius, battery voltage, and the r emaining battery capacity as a per centage of the fully char ged condition. This informa ...
-
APC 2000 - page 27
Page 25 5.0 Operation 5.7 Extended capabilities - continued ● On-battery output voltage (220/230/240 V ac versions only) - The UPS’s on-battery output voltage may be set to a nominal 220, 225, 230 or 240 V ac. The UPS’s default setting is 225 V ac. ● Utility failure sensitivity - The UPS’s sensitivity to line voltage distortions may be cu ...
-
APC 2000 - page 28
Page 26 6.0 UPS Monitoring 6.1 Over view A UPS system alone provides excellent protection fr om brief power problems. How- ever , during an extended power outage an unattended computer system will eventually shut down due to battery capacity exhaustion. T o pr event data corruption when the UPS shuts down, the computer must be informed by the UPS o ...
-
APC 2000 - page 29
Page 27 6.0 UPS Monitoring 6.4 Computer interface port The computer interface port is diagramed below for your r eference. Those with technical abilities wishing to use this port in a special application should be awar e of the following limitations and capabilities of the interface. ■ Outputs at pins 3, 5 and 6 are actually open collector output ...
-
APC 2000 - page 30
Page 28 7.0 Difficulty Caution ! CAUTION ! ■ This Uninterruptible Power Source contains potentially hazar dous voltages. Do not attempt to disassemble the unit. The unit contains no user serviceable parts. Repairs are performed only by factory trained service personnel. ■ This Uninterr uptible Power Source uses batteries. The batteries will eve ...
-
APC 2000 - page 31
Page 29 FRANÇAIS 7.0 Difficulté Attention ! A TTENTION! ■ Cette sour ce d’alimentation permanente (UPS) contient des circuits haute tension présentant un danger . Ne jamais essayer de le démonter . Il n’y a aucun composant qui puisse êtr e réparé par l’utilisateur . T outes les réparations doivent être effectuées par du personnel ...
-
APC 2000 - page 32
Page 30 DEUTSCH 7.0 Schwierigkeit V orsicht ! VORSICHT! ■ Im Inner en dieser unterbr echungsfr eien Stromversor gung herrschen potentiell gefährliche Spannungen. Nicht versuchen, das Gerät zu öf fnen. Es enthält keine vom Benutzer reparierbar en T eile. Reparatur en dürfen nur von ausgebildetem Kundendienstpersonal durchgeführt werden. ■ ...
-
APC 2000 - page 33
Page 31 ESP AÑOL 7.0 Dificultad ¡Cuidado! ¡CUIDADO! ■ Esta Fuente de ener gía ininterrumpible contiene niveles de voltaje peligr osos en potencia. No intente desarmar la unidad, pues no contiene piezas que puedan ser reparadas por el usuario. Las r eparaciones deben efectuarse únicamente por parte del personal de mantenimiento capacitado en ...
-
APC 2000 - page 34
Page 32 7.0 Difficulty 7.1 T roubleshooting chart PR OB LEM POSSIBLE CA USE ACTIO N TO TA K E U PS will not tu rn on . 1 . U PS Enab le s wi t c h is i n t he of f p os i t i on o r f r ont pan el s wi tc h not pr e s sed. 1 . T ur n o n t he r e ar pa nel U PS En abl e s wi t c h. P r es s f r o nt pa nel s wit c h to po w e r U PS an d l o ads. 2 ...
-
APC 2000 - page 35
Page 33 7.0 Difficulty 7.2 Battery r eplacement check Y ou can expect to r eceive 3 to 6 years of service life fr om the UPS's batteries when installed in a cool, dry location. Battery life is shortened when operated in an envir onment where the ambient temperatur e is normally above 30 ° C (86 ° F). The UPS automatically performs a battery ...
-
APC 2000 - page 36
Page 34 7.0 Difficulty 7.3 Obtaining Service The troubleshooting chart in section 7.1 covers most of the difficulties that a user may encounter under conditions other than a failur e of the UPS itself. For problems not cover ed in the chart, the procedur es outlined below should be followed. If your UPS should r equire service: ■ See the tr ouble ...
-
APC 2000 - page 37
Page 35 8.0 Storing the UPS 8.1 Storage conditions The UPS should be covered and stor ed upright in a cool dry location. The UPS should be stored with its battery in a fully char ged state. That is, the indicated battery capacity should be 100% befor e the UPS is switched off for storage. Disconnect accessories or cables connected at the computer i ...
-
APC 2000 - page 38
Page 36 9.0 Specifications Note: Wher e specifications ratings differ , values for the 100 V ac version are given in { } brackets, values for 208 V ac versions ar e given in ( ) brackets, and values for 220/230/240 V ac versions ar e given in [ ] brackets. 9.1 Input Nominal input voltage: single phase, {100 V ac}, 120 V ac, (208 V ac), [220/230/240 ...
-
APC 2000 - page 39
Page 37 9.0 Specifications 9.4 Noise and sur ge suppr ession Surge energy rating (one time, 10/1000 µs waveform) : {160 J}, 480 J, (480 J), [480 J]. Surge current capability (one time, 8/20 µs waveform) : 6500 Amp peak maximum. Surge response time: 0 ns (instantaneous) normal mode, <5 ns common mode. Surge voltage let-through: {<0.3%], < ...
-
APC 2000 - page 40
Page 38 9.0 Specifications 9.9 T ypical r un time versus load Note: Run times are typical at 25°C (77°F). Load 900VA mod el 1 250VA mo d el 200 0VA mo d e l Typ i cal comp u ter l oad (0.7 v o lt- am ps = Wat ts ) 50 VA 15 0 m in 29 0 mi n 45 0 mi n T y p i ca l A S CI I te rmi n a l 75 VA 12 5 m in 25 0 mi n 40 0 mi n Macintos h SE/30 100 VA 10 ...
-
APC 2000 - page 41
Page 39 Notes ...
-
APC 2000 - page 42
Page 40 DECLARA TION OF CONFORMITY Application of Council Directive(s): 89/336/EEC Standard(s) to which Conformity is Declared: EN55022, EN50082-1 Manufacturer's Name: AMERICAN POWER CONVERSION Manufacturer's Address: 132 FAIRGROUNDS ROAD WEST KINGSTON, RI 02892 USA Importer's Name: Importer's Address: T ype of Equipment: UNINTE ...
-
APC 2000 - page 43
Limited W arranty American Power Conversion (APC) warrants its products to be free from defects in materials and workmanship for a period of two years from the date of purchase. Its obligation under this warranty is limited to repairing or replacing, at its own sole option, any such defective products. To obtain service under warranty you must obta ...
-
APC 2000 - page 44
990-7001-A-8 10/93 ( PHONE PHONE PHONE PHONE PHONE (+33) 1.64.62.59.00 in Eur (+33) 1.64.62.59.00 in Eur (+33) 1.64.62.59.00 in Eur (+33) 1.64.62.59.00 in Eur (+33) 1.64.62.59.00 in Eur ope ope ope ope ope (401) 789-5735 world wide (401) 789-5735 world wide (401) 789-5735 world wide (401) 789-5735 world wide (401) 789-5735 world wide * MAILING MAIL ...
Avez-vous une question à propos de APC 2000?
Utiliser le formulaire ci-dessous
Si vous n’avez pas résolu votre problème avec APC 2000, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec APC 2000 il est probable qu’il a envie de partager la façon de le résoudre.