Manuel d’utilisation InFocus IN5124

34 pages 1.66 mb
Télécharger

Aller à la page of 34

Summary
  • InFocus IN5124 - page 1

    RS232 Command and Control Guide Regulatory models: W60, W61 010-0763-00 DISPERINDAG No. 0287/1.824.51/09.03 ...

  • InFocus IN5124 - page 2

    This page left blank intentionally ...

  • InFocus IN5124 - page 3

    1 Projector IN5122/IN5124 RS232 Command and Control Guide The signals listed on the following pages are used for initial setup, however the signal timings of some computer models may be different. In such a case, adjust V POSITION and H POSITION in the IMAGE menu. Back porch (B) Front porch (D) Back porch (b) Front porch (d) Active video (C) Data D ...

  • InFocus IN5124 - page 4

    2 Initial set signals Resolution Freq Standard DotCLK (MHz) fH (KHz) fV (Hz) H T otal (Pixels) H Res (Pixels) H Sync (Pixels) H Back Porch (Pixels) V T otal (Lines) V Res (Lines) V Sync (Lines) V Back Porch (Lines) C A B c a b 720x400 70 VESA-DMT 28.322 31.469 70.087 900 720 108 54 449 400 2 35 640x480 60 VESA-DMT 25.175 31.469 59.940 800 640 96 48 ...

  • InFocus IN5124 - page 5

    3 Resolution Freq Standard DotCLK (MHz) fH (KHz) fV (Hz) H T otal (Pixels) H Res (Pixels) H Sync (Pixels) H Back Porch (Pixels) V T otal (Lines) V Res (Lines) V Sync (Lines) V Back Porch (Lines) C A B c a b 720x400 70 VESA-DMT 28.322 31.469 70.087 900 720 108 54 449 400 2 35 640x480 60 VESA-DMT 25.175 31.469 59.940 800 640 96 48 525 480 2 33 640x48 ...

  • InFocus IN5124 - page 6

    4 A COMPUTER IN1, B MONITOR OUT D-sub 15pin mini shrink jack <Computer signal> • Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminated (positive) • H/V . sync. signal: TTL level (positive/negative) • Composite sync. signal: TTL level <Component video signal> • Video signal: - Y, Analog, 1.0±0.1Vp-p with composite sync, 7 ...

  • InFocus IN5124 - page 7

    5 E S-VIDEO Mini DIN 4pin jack • System: NTSC, P AL, SECAM, P AL-M, P AL-N, NTSC4.43, P AL(60Hz) Pin Signal 1 Color signal 0.286Vp-p (NTSC, burst), 75Ω terminator Color signal 0.300Vp-p (P AL/SECAM, burst) 75Ω terminator 2 Brightness signal, 1.0Vp-p, 75Ω terminator 3 Ground 4 Ground Connection to the por ts (continued) 4 3 2 1 F VIDEO RCA jack ...

  • InFocus IN5124 - page 8

    6 Connection to the por ts (continued) H AUDIO IN1, I AUDIO IN2 Ø3.5 stereo mini jack • 200 mV rms, 47kΩ terminator J AUDIO IN3 (R, L) K AUDIO OUT (R, L) RCA jack x2 RCA jack x2 • 200 mV rms, 47kΩ terminator • 200 mV rms, 1kΩ output impedance L MIC Ø3.5 mono mini jack <Low level> • 2 mV rms, 1kΩ terminator <High level> ...

  • InFocus IN5124 - page 9

    7 Connection to the por ts (continued) O USB TYPE B USB B type jack Pin Signal 1 +5V 2 - Data 3 + Data 4 Ground 4 3 1 2 P CONTROL D-sub 9pin plug • About the details of RS-232 communication, please refer to the section "RS-232 Communication". Pin Signal Pin Signal Pin Signal 1 (No connection) 4 (No connection) 7 RTS 2 RD 5 Ground 8 CTS ...

  • InFocus IN5124 - page 10

    8 SCART T o input SCART RGB signal; ex. Connection to the por ts (continued) T o input SCART RGB signal to the projector , use a SCART to RCA cable. Connect the plugs refer to above example. For more reference, please consult your dealer . SCART connector (jack) SCART cable (plug) RCA plugs ...

  • InFocus IN5124 - page 11

    9 CD (1) (1) -- RD(2) (2) RD TD (3) (3) TD DTR (4) (4) -- GND (5) (5) GND DSR (6) (6) -- R TS (7) (7) R TS DTS (8) (8) CTS RI (9) (9) -- RS-232 Communication RS-232 Communication When the projector connects to the computer by RS-232 communication, the projector can be controlled with RS-232 commands from the computer . For details of RS-232 command ...

  • InFocus IN5124 - page 12

    10 Command Control via the Network When the projector is connected to the network, the projector can be controlled with RS-232 commands from the computer with a web browser . For RS-232 command information, refer to the RS-232 Communication / Network command table ( & 16 ). Connection 1. T urn of f the projector and the computer . 2. Connect th ...

  • InFocus IN5124 - page 13

    11 Communication P or t The following port is assigned for command control. TCP #23 Congure the following items from a web browser when command control is used. Port Settings Network Control Port1 (Port: 23) Port open Click the [Enable] check box to open [Network Control Port1 (Port: 23)] to use TCP #23. Default setting is “Enable”. Authenti ...

  • InFocus IN5124 - page 14

    12 Command Control via the Networ k (continued) RS-232 Commands IMPORT ANT : When formatting commands sent from a control system or computer , enclose commands in parentheses “(“ and “)”. When entering custom commands into Scheduled T asks in the projector ’s web interface, enclose commands in less than/ greater than symbols “<” an ...

  • InFocus IN5124 - page 15

    13 Command Control via the Networ k (continued) A write request example: (AAA####) where (starts the command AAA denotes the command #### denotes the value to be written (leading zeros not necessary) ) ends the command Some commands have ranges, while others are absolute. If a number greater than the maximum range is received, it is automatically s ...

  • InFocus IN5124 - page 16

    14 This projector is equipped with NETWORK BRIDGE function. When the projector connects to the computer by LAN communicaton, an external device that is connected with this projector by RS-232 communication can be controlled from the computer as a network terminal. For details, see the 6. Network Bridge function in the Network Guide . Connection 1. ...

  • InFocus IN5124 - page 17

    15 Communication settings For communication setting, use the OPTION - SERVICE - COMMUNICA TION menu. ( & OPTION menu - SERVICE - COMMUNICA TION in the User's Manual ) Item Condition BAUD RA TE 4800bps / 9600bps / 19200bps / 38400bps Data length 8 bit (xed) P ARITY NONE/ODD/EVEN Start bit 1 bit (xed) Stop bit 1 bit (xed) T ransmiss ...

  • InFocus IN5124 - page 18

    16 RS-232 Communication / Network command table RS-232 Communication / Netw ork command ta ble Function Command RW Min Max Default Step BASIC MENU Aspect Ratio 0: Auto 1: Native (IN5124 only) 2: 4:3 3: 16:9 6: 16:10 ARZ RW 0 6 0 Auto Keystone Execute 1: Execute AV K W 0 1 n/a Horizontal Keystone DKH RW 38 218 128 1 V ertical Keystone DKV RW 38 218 ...

  • InFocus IN5124 - page 19

    RS-232 Communication / Netw ork command ta ble (continued) 17 (continued on next page) Function Command RW Min Max Default Step Presets 1: User 5: Presentation 7: Video 10: Bright 1 1: Whiteboard 12: Blackboard 13: Greenboard 15: Dynamic PST RW 1 15 5 (Computer in 1) 5 (Computer in 2) 5 (LAN) 5 (USB T ype A) 5 (USB T ype B) 15 (HDMI) 15 (Component) ...

  • InFocus IN5124 - page 20

    RS-232 Communication / Netw ork command ta ble (continued) 18 (continued on next page) Function Command RW Min Max Default Step Gamma 32: 1 Default 16: 1 Custom 33: 2 Default 17: 2 Custom 34: 3 Default 18: 3 Custom 35: 4 Default 19: 4 Custom 36: 5 Default 20: 5 Custom 37: 6 Default 21: 6 Custom GTB RW 16 37 32 (Computer in 1) 32 (Computer in 2) 32 ...

  • InFocus IN5124 - page 21

    RS-232 Communication / Netw ork command ta ble (continued) 19 (continued on next page) Function Command RW Min Max Default Step Gamma Custom-4 Point 7 G41 RW 11 2 144 128 1 Gamma Custom-4 Point 8 G42 RW 11 2 144 128 1 Gamma Custom-5 Point 1 G43 RW 11 2 144 128 1 Gamma Custom-5 Point 2 G44 RW 11 2 144 128 1 Gamma Custom-5 Point 3 G45 RW 11 2 144 128 ...

  • InFocus IN5124 - page 22

    RS-232 Communication / Netw ork command ta ble (continued) 20 (continued on next page) Function Command RW Min Max Default Step Color T emperature - 6 Blue Gain BG6 RW 96 160 128 1 Color T emperature - 1 Red Offset RF1 RW 96 160 128 1 Color T emperature - 2 Red Offset RF2 RW 96 160 128 1 Color T emperature - 3 Red Offset RF3 RW 96 160 128 1 Color T ...

  • InFocus IN5124 - page 23

    RS-232 Communication / Netw ork command ta ble (continued) 21 (continued on next page) Function Command RW Min Max Default Step ADV ANCED MENU: IMAGE Aspect Ratio 0: Auto 1: Native (IN5124 Only) 2: 4:3 3: 16:9 6: 16:10 ARZ RW 0 6 0 Overscan 0: Off 1: Zoom 2: Crop OVS RW 0 2 0 V ertical Position VPS RW if def<128: 0 else: def -128 def +128 auto 1 ...

  • InFocus IN5124 - page 24

    RS-232 Communication / Netw ork command ta ble (continued) 22 (continued on next page) Function Command RW Min Max Default Step S-Video Standard 0: Auto 1: NTSC 2: P AL 3: SECAM 4: NTSC4.43 5: M-P AL 6: N-P AL ? RW 0 6 0 HDMI Format 0: Auto 1: Video 2: Computer RW 0 2 0 HDMI Range 0: Normal 1: Enhanced 16: Auto RW 0 16 16 Component 0: Component 1: ...

  • InFocus IN5124 - page 25

    RS-232 Communication / Netw ork command ta ble (continued) 23 (continued on next page) Function Command RW Min Max Default Step Corner Correction all corners Reset 0: n/a 1: enable CNR RW 0 1 n/a Side Correction Left Gain SC1 RW 98 158 128 1 Side Correction Right Gain SC2 RW 98 158 128 1 Side Correction V Position SC3 RW 0 768 (IN5122) 800 (IN5124) ...

  • InFocus IN5124 - page 26

    RS-232 Communication / Netw ork command ta ble (continued) 24 (continued on next page) Function Command RW Min Max Default Step Monitor Out for Source 5 (HDMI) 1: Computer in 1 2: Computer in 2 255: Off SM5 RW 1 255 1 Monitor Out for Source 6 (Component) 1: Computer in 1 2: Computer in 2 255: Off SM6 RW 1 255 1 Monitor Out for Source 7 (S-Video) 1: ...

  • InFocus IN5124 - page 27

    RS-232 Communication / Netw ork command ta ble (continued) 25 (continued on next page) Function Command RW Min Max Default Step Audio for Source 0 (Computer in 1) 0: Audio 1 1: Audio 2 2: Audio 3 5: Mute SA0 RW 0 5 0 Audio for Source 1 (Computer in 2) 0: Audio 1 1: Audio 2 2: Audio 3 5: Mute SA1 RW 0 5 1 Audio for Source 2 (LAN) 0: Audio 1 1: Audio ...

  • InFocus IN5124 - page 28

    RS-232 Communication / Netw ork command ta ble (continued) 26 (continued on next page) Function Command RW Min Max Default Step HDMI Noise Cancel 0: Disable 1: Enable HNC RW 0 1 1 MIC Level 0: Low 1: High MIK RW 0 1 0 MIC V olume MIC RW 0 48 24 1 ADV ANCED MENU: SCREEN Menu Positon H OFH RW 0 10 0 (left) 1 Menu Positon V OFV RW 0 10 10 (top) 1 Blan ...

  • InFocus IN5124 - page 29

    RS-232 Communication / Netw ork command ta ble (continued) 27 (continued on next page) Function Command RW Min Max Default Step RS-232 Communication / Netw ork command ta ble (continued) Auto Power 0: Disable 1: Enable AOT RW 0 1 0 USB T ype B 0: Mouse 1: USB Display USB RW 0 1 1 Custom Key (Effect) 0: Blank 1: Mute 2: Aspect Ratio 3: Source 4: Aut ...

  • InFocus IN5124 - page 30

    RS-232 Communication / Netw ork command ta ble (continued) 28 (continued on next page) Function Command RW Min Max Default Step RS-232 Communication / Netw ork command ta ble (continued) Source 4 0: Computer in 1 1: Computer in 2 2: LAN 3: USB T ype A 4: USB T ype B 5: HDMI 6: Component 7: S-Video 8: Video SR4 RW 0 8 8 Power-up Source 0: Computer i ...

  • InFocus IN5124 - page 31

    RS-232 Communication / Netw ork command ta ble (continued) 29 (continued on next page) Function Command RW Min Max Default Step My Image Display 0: Off 1: Image-1 2: Image-2 3: Image-3 4: Image-4 MIF RW 0 4 0 My Image Delete Image-1 1: delete MD1 W 0 1 n/a My Image Delete Image-2 1: delete MD2 W 0 1 n/a My Image Delete Image-3 1: delete MD3 W 0 1 n ...

  • InFocus IN5124 - page 32

    RS-232 Communication / Netw ork command ta ble (continued) 30 (continued on next page) Function Command RW Min Max Default Step Freeze 0: Off 1: On FRZ RW 0 1 0 INFOCUS UNIQUE About (Source Info) 0: n/a 1: enable ABT W 0 1 n/a Lamp Lit 0: not lit 1: lit LML R 0 1 0 Number of Lamp Resets LMR R 0 32766 0 Lamp T otal On T ime (All Bulbs) LMT R 0 21474 ...

  • InFocus IN5124 - page 33

    31 PJLink command PJLink command POWR Power Control 0 = Standby 1 = Power On POWR ? Power Status inquiry 0 = Standby 1 = Power On 2 = Cool Down INPT Input Source selection 1 1 = COMPUTER IN 1 12 = COMPUTER IN 2 21 = COMPONENT 22 = S-VIDEO 23 = VIDEO 31 = HDMI 41 = USB TYPE A 51 = LAN 52 = USB TYPE B INPT ? Input Source inquiry 1 1 = COMPUTER IN 1 1 ...

  • InFocus IN5124 - page 34

    32 PJLink command (continued) Commands Control Description Parameter or Response ERST ? Error Status inquiry 1st byte: Refers to Fan error; one of 0 to 2 2nd byte : Refers to Lamp error; one of 0 to 2 3rd byte: Refers to T emperature error; one of 0 to 2 4th byte: Refers to Cover error; one of 0 to 2 5th byte: Refers to Filter error; one of 0 to 2 ...

Fabricant InFocus Catégorie Projector

Les documents que nous recevons du fabricant de l'appareilInFocus IN5124 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques InFocus
- manuels d’utilisations IN5124
- fiches produit InFocus
- dépliants
- ou étiquettes-énergie InFocus IN5124
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation InFocus IN5124.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation InFocus IN5124, manuels d’entretien, brefs manuels ou manuels de l’utilisateur InFocus IN5124. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit InFocus IN5124.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil InFocus IN5124, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser InFocus IN5124 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs InFocus IN5124.

Le manuel d’utilisation complet InFocus, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel InFocus IN5124 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières InFocus IN5124, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lInFocus IN5124 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil InFocus IN5124 - qui devraient nous aider dans les premières étapes lors de l'utilisation InFocus IN5124
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de InFocus IN5124
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service InFocus IN5124 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de InFocus IN5124?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec InFocus IN5124, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec InFocus IN5124 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (0)