-
Grizzly H7677 - page 1
COPYRIGHT © AUGUST, 2005 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #BL7292 PRINTED IN CHINA 1 8 G A U G E S T A P L E R K I T MODEL H7677 INSTRUCTION MANUAL ...
-
Grizzly H7677 - page 2
H7677 18 Gauge Stapler Kit -2 - Safety Instructions for Pneu matic T ools 1. KEEP ALL SAFETY DEVICES IN PLACE and in working order. 2. REMOVE ADJUSTING KEYS AND WRENCHES . Form habit of check- ing to see that keys and adjusting wrenches are removed from tool before operation. 3. KEEP WORK AREA CLEAN . Cluttered areas and benches invite accidents. 4 ...
-
Grizzly H7677 - page 3
H7677 18 Gauge Stapler Kit -3 - 10. USE PROPER AIR HOSE for the tool. Make sure your air hose is in good condition and is long enough to reach your work without stretching. 11. WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neck - ties, rings, bracelets, or other jew- elry which may get caught in moving parts. Non-slip footwear is recom- ...
-
Grizzly H7677 - page 4
H7677 18 Gauge Stapler Kit -4 - 1. HAND INJURIES. Do not place your hands near the staple point of entry. A staple can deflect and tear through the surface of the workpiece, punc - turing your hand or fingers. 2. COMBUSTIBLE GASES. Never connect the stapler to pressurized oxygen or other combustible gases as a power source . Only use fil- tered, lu ...
-
Grizzly H7677 - page 5
H7677 18 Gauge Stapler Kit -5 - Operating t his stapler can propel objects into the air, causing imme- diate eye damage. To protect your- self, always wear American National Standards Institute (ANSI) approved safety glasses or goggles when oper- ating this equipment. In addition, this stapler discharges at 82 decibels. To protect your hearing, alw ...
-
Grizzly H7677 - page 6
H7677 18 Gauge Stapler Kit -6 - SE CTI ON 2 : INTRODU C TION If you have any c omme nts reg ard ing th is man ual, pl ease w rite to u s at the follow ing add ress : Grizzly Industrial, Inc. C/O Technical Documentation Manager P.O. Box 2069 Bellingham, WA 98227-2069 Mo st im por t antl y , we sta nd b ehin d ou r too ls. If you have any ser vi ce q ...
-
Grizzly H7677 - page 7
H7677 18 Gauge Stapler Kit -7 - SE CTI ON 3 : SET UP Figure 1. Model H7677 inventory. Unpacki ng Y our Mode l H7677 sta pler kit left our w are- hou se in a carefu lly packe d box. If you dis cover the sta pler is dam aged af ter you have s ign ed fo r d eliver y, ple ase im med i- ately cal l Cus tomer Servi ce at (570) 546 - 96 63 for advi ce. Sa ...
-
Grizzly H7677 - page 8
H7677 18 Gauge Stapler Kit -8 - Compressed Air Sy stem The Mo del H7677 is de sign ed to b e o per- ated at 6 0 - 1 0 0 PSI usi ng c lean , dr y , regu - late d, c ompr esse d ai r . D O N OT exc ee d th e 120 P SI m axi mum op er atin g p re s- sur e fo r you r mo de l. Befo re us ing your new st aple r , regul ate the a ir pre ssure o n your ai r ...
-
Grizzly H7677 - page 9
H7677 18 Gauge Stapler Kit -9 - Safety Y oke A s afet y yoke me cha nism (bu mp fire) on the no se of the st apl er ac ts as a s afet y devi ce. Whe n t he t rigg er i s p ulle d, t he sta pler wil l not f ire unt il t he safet y yo ke mec han ism is depr esse d. Befo re yo u us e you r st apl er f or t he f irs t tim e, che ck th e safet y yoke me ...
-
Grizzly H7677 - page 10
H7677 18 Gauge Stapler Kit -10 - SE CTI ON 4 : OP ER A TIONS Loadin g Figure 3. Latching pusher in groove. When replacing staples in your Model H7677, follow these guidelines: Gauge: 18 Length: 1 ⁄ 2 " –1" Capacity: 100 Crown: 1 ⁄ 4 " To load your stapler: 1. DISCONNECT STAPLER FROM THE AIR SUPPLY! 2. Grip the stapler firmly, a ...
-
Grizzly H7677 - page 11
H7677 18 Gauge Stapler Kit -11 - 5. Pull the trigger. — If the staple drove into the wood far enough, continue with your intended operations. — If the staple either went too far or not far enough, then adjust the air pressure. More air pressure will make the staple go deeper and less air pressure will decrease the staple penetration. 3. Depress ...
-
Grizzly H7677 - page 12
H7677 18 Gauge Stapler Kit -12 - A jammed staple must be cleared before using the stapl er again. The two places where a staple can get jammed are the magazine and the discharge area. To clear a jammed staple from the dis- charge area: 1. DISCONNECT STAPLER FROM THE AIR SUPPLY! 2. Pull back and latch the magazine. 3. Remove the staple from the maga ...
-
Grizzly H7677 - page 13
H7677 18 Gauge Stapler Kit -13 - Replacin g Pist ons / O - Rin gs If you use your stap ler day in an d day out , re pair pisto ns are c heap insu ranc e agai nst wa sted do wn tim e and los t profi ts, in t he event t hat a p isto n or p iston sh aft bec ome s wo rn out . A re plac eme nt p isto n and O -r ing k it, par t PH76770 69, may be pur cha ...
-
Grizzly H7677 - page 14
H7677 18 Gauge Stapler Kit -14 - SE CTI ON 5 : MAINTENANCE Cleanin g Use a go od so lvent to c lean t he n ose ass emb ly of t he s tap ler. Alw ays be sure tha t th e st apl er i s dr y bef ore u sing it agai n. Do n ot all ow dus t, c hips , san d, etc. int o the ai r c onne cto rs or into t he b ody of t he sta pler ; thi s may res ult in leak s ...
-
Grizzly H7677 - page 15
H7677 18 Gauge Stapler Kit -15 - H7677 Parts Bre ak down 67 69 68 66 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 39 40 45 44 43 38 37 36 25 25 31 3 4 35 34 33 32 60 24 26 25 25 24 27 28 29 30 41 42 52 51 50 49 48 47 46 53 54 55 56 57 58 59 62 63 64 65 61 ...
-
Grizzly H7677 - page 16
H7677 18 Gauge Stapler Kit -16 - H7677 Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PH7677001 SPECIAL SCREW 36 PH7677036 TRIGGER VALVE GUIDE 2 PH7677002 AIR DEFLECTOR 37 PH7677037 O-RING 11.2 X 2 3 PSB15M CAP SCREW M5-.8 X 20 38 PH7677038 COMPRESSION SPRING 4 PLW01M LOCK WASHER 5MM 39 PH7677039 SAFETY STAND 5 PH7677005 CYLINDER COVER ...
-
Grizzly H7677 - page 17
H7677 18 Gauge Stapler Kit -17 - TROUBLESHOOTING Symptom Possible Cause Solution Air leaking at trig- ger valve area. 1. O-rings in trigger valve hous- ing are damaged. 1. O-rings must be replaced & operation of safety yoke must be checked. Air leaking between housing and hose. 1. Loose screws in housing. 2. Damaged O-ring. 3. Loose air fitting ...
-
Grizzly H7677 - page 18
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty and any and all warr ...
-
Grizzly H7677 - page 19
WARRANTY CARD Name _________________________________________________________________ Street _________________________________________________________________ City _______________________ State _________________________ Zip _________ Phone # ____________________ Email ________________________ Invoice # _____ Model # ____________________ Order # ____ ...
-
Grizzly H7677 - page 20
FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name________________________________ Street________________________________ City______________State______Zip_______ Send a Grizzly Catalog to a friend: Place Stamp Here ...
Avez-vous une question à propos de Grizzly H7677?
Utiliser le formulaire ci-dessous
Si vous n’avez pas résolu votre problème avec Grizzly H7677, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Grizzly H7677 il est probable qu’il a envie de partager la façon de le résoudre.