Français dropdown-ico

Manuel d’utilisation Madge Networks 802.11b

27 pages 0.91 mb
Télécharger

Aller à la page of 27

Summary
  • Madge Networks 802.11b - page 1

    W ireless LAN Security Smart Wireless Access Point 802.11b (95-10) User Guide 100-408-01 Copyright © 2002 Madge Networks. All ri ghts reserved. 20 Jul 2002 ...

  • Madge Networks 802.11b - page 2

    Federal Communication Commission Interferen ce Statement This equipment has been tested and found to comply w ith the lim its for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are desi gned to provide reasonable pr otection against harmful interference in a residentia l installation. This equipment generates, uses and ...

  • Madge Networks 802.11b - page 3

    R&TTE Compliance Statement This equipment complies with all the require m ents of DIRECTIVE 1999/5/CE OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication terminal equipment and the m utual rec ognition of their conformity (R&TTE). The R&TTE Directive repeals and replaces in the di rective ...

  • Madge Networks 802.11b - page 4

    Contents 1 Introduction................................................................................................................. ........................... 1 1.1 Overview ................................................................................................................... ..................... 1 1.2 Features ................. ...

  • Madge Networks 802.11b - page 5

    1 Introduction 1.1 Overview The Madge advanced Smart W ireless Access Po int (advanced AP) enables IEEE 802.11b client computers to access the resources on an Ethernet network. Because it supports IEEE 802.1x and RADIUS (Remote Authentication Dial-In User Service) for user-based authen tication and dynamic encryption key distribution, it is suitabl ...

  • Madge Networks 802.11b - page 6

    Hardware Watchdog Timer. If the AP fir m ware enters an invalid state, the hardware watchdog timer will detect this situation and res tart the advanced AP. According ly, the advanced AP can recover from certain error situations.  2 First-Time Installation and Configuration 2.1 Powering up the AP To power the AP with the supplied power adapter: 1 ...

  • Madge Networks 802.11b - page 7

    2.3 Preparing for Configuration For the user (or administrator) to configure an ad vanced AP, a managing computer with a Web browser is needed. For first-time configuration of an advanced AP, an Ethernet netw ork interface card (NIC) should have been installed in the mana ging computer. For maintenance-conf iguration of a deployed advanced AP, eith ...

  • Madge Networks 802.11b - page 8

    2.4 Configuring the Advanced AP After the IP addressing issue is resolved, launch a Web browser on the managing computer. Then, go to “ http://192.168.0.1 ” to access the Web-based Network Manager start page. TIP: For maintenance configuration of an advanced AP, the advanced AP can be reached by its host name using a Web browser. For example, i ...

  • Madge Networks 802.11b - page 9

    Fig. 4. The Start page. 2.4.2 Step 1: Configure TCP/IP Settings Fig. 5. TCP/IP settings. Go to the TCP/IP, Addressing section to configure IP address settings. The IP address can be manually set or automatically assigned by a DHCP server on the LAN. If you are manually setting the IP Address , Subnet Mask , and Default Gateway settings, set them ap ...

  • Madge Networks 802.11b - page 10

    2.4.3 Step 2: Configure IEEE 802.11 Settings Fig. 6. IEEE 802.11b communication settings. Go to the IEEE 802.11, Communication section to configure IEEE 802.11b-related communication settings, including Regulatory Domain , Channel Number , and Network Name (SSID) . The number of available RF channe ls depends on local regulations; therefore you hav ...

  • Madge Networks 802.11b - page 11

    On the start page, you can review all the settings you have made . Changes are high lighted in red . If they are OK, click Restart to restart the advanced AP for the new settings to take effect. NOTE: About 7 seconds are needed for the advanced AP to complete its restart process. 2.5 Deploying the Advanced AP After the settings have been configured ...

  • Madge Networks 802.11b - page 12

    1. Launch the configuration/monitoring utility prov ided by the vendor of the installed WLAN NIC. 2. Check if the client computer is associated to an access point, and the access point is the advanced AP. If the check fails, see Appendix B-1, “Wirel ess Settings Problems” for troubleshooting. 2.7.2 Checking if the TCP/IP-Related Settings Work T ...

  • Madge Networks 802.11b - page 13

    3 Using the Web-Based Network Manager This section explains each management pa ge of the Web-based Network Manager. 3.1 Overview Fig. 8. The Start page. The left side of the start page contains a menu for the user to carry out commands. Here is a brief description of the hyperlinks in the menu:           Home. For goin ...

  • Madge Networks 802.11b - page 14

      Advanced. Advanced settings of the advanced AP. Management. UPnP and SNMP settings. Fig. 9. Save, Save & Restart, and Cancel. At the bottom of each page, there are up to three buttons— S ave , Save & Restart , and Cancel . Clicking Save stores the settings changes to the memory of the advanced AP and brings the user back to the st ...

  • Madge Networks 802.11b - page 15

    3.2 General Operations 3.2.1 Changing Password Fig. 11. Password. On this page, the user could cha nge the password for the right to modify the configuration of the advanced AP. The new password must be typed twice for confirmation. 3.2.2 Upgrading Firmware Fig. 12. Firmware Upgrade. The advanced AP can be triggered to download updated firmware fro ...

  • Madge Networks 802.11b - page 16

    Fig. 13. TFTP Server. TIP: It's more convenient to use the Firmware Upgr ade Wizard of Wireless Ne twork Manager to upgrade the firmware of an advanced AP. See section 4. NOTE: After the dialog box of the TFTP server program appears, be sure to specify the working folder within which the downloade d firmware files reside. NOTE: The LAN IP addr ...

  • Madge Networks 802.11b - page 17

    The IP address of the AP can be manually set or au tomatically assign ed by a DHC P server on the LAN. If you are manually setting the IP Address , Subnet Mask , and Default Gateway settings, set them appropriately, so that they comply with your LAN environment. In addition, you can specify the Host Name and Domain (DNS suffix) of the AP. 3.4 Confi ...

  • Madge Networks 802.11b - page 18

    802.1x EAP-MD5. The IEEE 802.1x functionality is enabled and the username/password-based EAP-MD5 authentication is used. No data encryption.        802.1x EAP-MD5 + 64-bit WEP. The IEEE 802.1x functionality is enabled and the username/password-based EAP-MD5 authentication is used. Data encryption is achieved by 64-bit WEP. 802. ...

  • Madge Networks 802.11b - page 19

    The IEEE 802.1x functionality of the a dvanced AP is controlled by the security mode (see Section 3.4.2). The advanced AP supports two authentication mechan ism s—EAP-MD5 (Message Digest version 5) and EAP-TLS (Transport Layer Security). If EAP-MD5 is used, the user has to give his or her user name and password for authentication. If EAP-TLS is u ...

  • Madge Networks 802.11b - page 20

    3.5 Configuring Advanced Settings 3.5.1 Management 3.5.1.1 SNMP Fig. 19. SNMP settings. The AP can be managed by SNMP (Simple Network Ma nagem ent Protocol), and the SNMP management functionality can be disabled. The us er can specif y the name (used as a password ) of the read-only and read-write community. In addition, up to 5 SNMP trap targets c ...

  • Madge Networks 802.11b - page 21

    2. If AutoPlay is enabled then the “Accept W arranty Dialog” should appear (if not, it can be run from D:Setup.exe where D: is the drive letter of your CD -ROM). Read the agreement and click Accept if you agree to the terms of the W arrant y. The following dialog will appear: Fig. 21. Setup top-level menu. 3. Click Install utilities and driver ...

  • Madge Networks 802.11b - page 22

    4.2 Using the Wireless Network Manager When the Installer Wizard is com plete the Wireless Network Manager program will b e available in the Programs section of your Windows Start menu. The first time the Wireless Network Manager runs it presents the Wireless Configuration Wiz ard that will help you make the a ppropriate settings for th e various e ...

  • Madge Networks 802.11b - page 23

    Fig. 25. Typical Wireless Network Manager dialog. Use the On-line help to guide you thr ough the features and functions of the Wireless Network Manager . All the features of the Web-based Network Mana ger (see section 3) are available using the Wireless Network Manager , and more. 100-408-01 Copyright © 2002 Madge Networks. All rights reserved. Pa ...

  • Madge Networks 802.11b - page 24

    Appendix A A-1: Default Settings TIP: Press the Default ( SF-Reset , or Soft-Reset ) switch on the housing of a powered-on advanced AP to reset the configuration settings to factory-default values. Setting Name Default Value Global User Name root Password root Host Name “M95-10xxxxxx” where xxxxxx = last 6 hex digits of the AP's MAC addres ...

  • Madge Networks 802.11b - page 25

    Appendix B: Troubleshooting Check the following first:             Make sure that the power of the advanced AP is on and the Ethernet cables are connected firmly to the RJ-45 jacks of the advanced AP. Make sure that the LED ALV of the advanced AP is blinking to indicat e the advanced AP is working. Make sure the ...

  • Madge Networks 802.11b - page 26

    For a wireless client computer to communicate with a correspondent ho st on the Internet by the host’s domain name (e.g. http://www.madge.com ), it first sends a DNS request to a DNS server on the Internet. The DNS request travels first to the advanced AP, the a dvanced AP then relays this r equest to the default gateway of the client computer. F ...

  • Madge Networks 802.11b - page 27

    B-3: Other Problems 100-408-01 Copyright © 2002 Madge Networks. All rights reserved. Page 23   The AP has been set to obtain an IP address au tomatically by DHCP. How can I know its acquired IP address so that I can ma nage it using a W eb browser? Use the utility, Wireless Router/AP Browser ( WLBrw sr.exe ), in the “ APUtilities ” fold ...

Fabricant Madge Networks Catégorie Network Card

Les documents que nous recevons du fabricant de l'appareilMadge Networks 802.11b peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Madge Networks
- manuels d’utilisations 802.11b
- fiches produit Madge Networks
- dépliants
- ou étiquettes-énergie Madge Networks 802.11b
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Madge Networks 802.11b.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Madge Networks 802.11b, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Madge Networks 802.11b. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Madge Networks 802.11b.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Madge Networks 802.11b, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Madge Networks 802.11b par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Madge Networks 802.11b.

Le manuel d’utilisation complet Madge Networks, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Madge Networks 802.11b - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Madge Networks 802.11b, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lMadge Networks 802.11b qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Madge Networks 802.11b - qui devraient nous aider dans les premières étapes lors de l'utilisation Madge Networks 802.11b
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Madge Networks 802.11b
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Madge Networks 802.11b dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Madge Networks 802.11b?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Madge Networks 802.11b, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Madge Networks 802.11b il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)