Français dropdown-ico

Manuel d’utilisation Husqvarna 320 AWD

36 pages 4.34 mb
Télécharger

Aller à la page of 36

Summary
  • Husqvarna 320 AWD - page 1

    E E E E n n n n g g g g l l l l i i i i s s s s h h h h Rider 318 Rider 320 A WD Oper ator ′ s manual Please r ead the operator’ s manual carefull y and make sur e you understand the instructions before using the machine. ...

  • Husqvarna 320 AWD - page 2

    2 – English CONTENTS Contents CONTENTS Contents ...................................................................... 2 Ser vice journal Pre-deliv er y ser vice ..................................................... 3 After the first 8 hours ................................................... 3 INTR ODUCTION Dear Customer , ..................... ...

  • Husqvarna 320 AWD - page 3

    English – 3 Ser vice journal Pre-deliver y service 1 Charge the batter y f or 4 hours at max. 3 amp. 2 Fit steering wheel, seat and any optional equipment. 3 Check and adjust tyre pressure (60 Kpa, 0.6 bar , 9 PSI). 4 Adjust cutting unit: Adjust lift springs (effectiv e weight of cutting unit should be 12-15kg / 26.5-33 lb). Adjust cutting unit s ...

  • Husqvarna 320 AWD - page 4

    4 – English INTR ODUCTION Dear Customer , Thank y ou f or choosing a Husqvarna Rider . Husqvarna Riders are built to a unique design with a front-mounted cutting unit and a patented ar ticulated steering. Riders are designed f or maximum efficiency e ven in small or confined areas . The closely grouped co ntrols and pedal-operated h ydrostatic ...

  • Husqvarna 320 AWD - page 5

    English – 5 KEY T O SYMBOLS Symbols These symbols are on the machine and in the instr uctions. W ARNING! Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine . Alw a ys wear: • Approv ed he ...

  • Husqvarna 320 AWD - page 6

    6 – English KEY T O SYMBOLS Star ting instructions Switch off the engine and take off the ignition cable bef ore repairs or maintenance Check the engine’ s oil le vel Check tr ansmission oil lev el Lift up the cutting unit Apply the par king brak e. If the engine is cold, use the chok e Release the par king brak e before driving ...

  • Husqvarna 320 AWD - page 7

    English – 7 WHA T IS WHA T? Location of the controls 12 3 4 6 8 7 9 12 14 13 15 10 11 5 1 Speed limiter f or driving forward 2 Speed limiter f or rev ersing 3 Lifting le ver f or the cutting unit 4 Cutting height adjustment le ver 5 Ignition lock 6 Throttle control/choke control 7 Counter 8 Cov er lock 9 P arking brake 10 Lock b utton f or parkin ...

  • Husqvarna 320 AWD - page 8

    8 – English SAFETY INSTR UCTIONS Safety instructions These instructions are for y our saf ety . Read them carefully . Insure y our Rider • Check the insur ance cov erage f or your ne w Rider. • Contact your insur ance company . • Y ou should hav e fully comprehensive insurance including: third par ty , fire, damage, theft and liability Gen ...

  • Husqvarna 320 AWD - page 9

    English – 9 SAFETY INSTR UCTIONS • Ne ver allo w children or other persons not trained in the use of the machine to use or ser vice it. Local laws ma y regulate the age of the user . • Use hearing protection to minimise the r isk of hearing impairment. • Ne ver w ear loose fitting clothes that can catch in moving par ts. • Ne ver use the ...

  • Husqvarna 320 AWD - page 10

    10 – English SAFETY INSTR UCTIONS • F ollow the manuf acturer’ s recommendations regarding wheel weights or counterbalance weights to increase machine stability . Children • Serious accidents may occur if y ou f ail to be on your guard f or children in the vicinity of the machine. Children are often attracted to the machine and mowing. Nev ...

  • Husqvarna 320 AWD - page 11

    English – 11 SAFETY INSTR UCTIONS • Do not change the setting of gov ernors. If you run too fast, you risk damaging the machine components. See chapter on T echnical data f or highest per mitted engine speed. • Ne ver use the machine indoors or in spaces lac king proper ventilation. Exhaust fumes contain carbon mono xide, an odourless, poison ...

  • Husqvarna 320 AWD - page 12

    12 – English PRESENT A TION Presentation Cong ratulations on y our choice of an e xcellent quality product that will give y ou great pleasure for man y years . This operator’ s manual describes Rider 318 and Rider 320 A WD . Rider 320 A WD is equipped with all wheel dr ive . The power tr ansmission from the engine is handled by a h ydrostatic t ...

  • Husqvarna 320 AWD - page 13

    English – 13 PRESENT A TION Seat The seat has a jointed attachment on the front edge and can be tipped f orward. The seat can also be adjusted lengthwa ys. Loosen the handles under the seat and adjust it f orwards or backw ards to the desired position. Fueling The engine runs on unleaded petrol with a minimum octane rating of 85 (not mix ed with ...

  • Husqvarna 320 AWD - page 14

    14 – English Driving Bef ore star ting • Read the saf ety instructions and information concer ning the placement of controls and functions bef ore star ting. • P erform daily maintenance before starting as set out in the Maintenance schedule. Star t the engine 1 Make sure that the clutch control is depressed. Rider 320 A WD has one control fo ...

  • Husqvarna 320 AWD - page 15

    English – 15 Driving Connecting the jump leads • Connect each end of the red cable to the POSITIVE pole (+) on each batter y , e xercise care not to short circuit any of the ends against the chassis. • Connect one end of the blac k cable to the NEGA TIVE pole (-) on the fully charged batter y . • Connect the other end of the blac k cable to ...

  • Husqvarna 320 AWD - page 16

    16 – English Driving Cutting tips • Localise and mark stones and other fixed objects to a void collision. • Star t with a high cutting height and reduce down until the required mowing results are obtained. • The mowing result will be best with the highest permitted engine speed, see technical data, (the blades rotate rapidly) and low speed ...

  • Husqvarna 320 AWD - page 17

    English – 17 Maintenance Maintenance schedule The f ollowing is a list of the maintenance which should be conducted on the machine. For those points not described in this manual, visit an authorised ser vice workshop. 1) First change after 8 hours. When oper ating with a heavy load or at high ambient temperatures , replace e very 50 hours. 2) Mai ...

  • Husqvarna 320 AWD - page 18

    18 – English Maintenance Cleaning Clean the machine directly after use. It is much easier to wash off grass cuttings bef ore they dr y . Oily dir t can be remov ed using a cold degreasing agent. Spra y on a thin la yer . Rinse at normal water pressure. Do not direct the jet tow ards electrical components or bearings. Do not rinse hot surfaces suc ...

  • Husqvarna 320 AWD - page 19

    English – 19 Maintenance • If necessar y , the wires can be adjusted by tightening the adjuster nuts on each side of the steering collar . Do not ov er tighten the cables; they should only be drawn in tow ards the steering collar . Hold the cable , f or example using an adjustab le wrench, so that it does not twist. If the adjustment is only ma ...

  • Husqvarna 320 AWD - page 20

    20 – English Maintenance Replacement of fuel filter Replace the fuel filter e very 100 running hours (once per season) or more frequently if it is clogged. Replace the filter as f ollows: 1 Open the engine cov er . 2 Mov e the hose clips aw a y from the filter . Use a pair of flat pliers. 3 Pull off the filter from the hose ends. 4 Press th ...

  • Husqvarna 320 AWD - page 21

    English – 21 Maintenance Ignition system The engine is equipped with an electronic ignition system. Only the spark plug requires maintenance. F or recommended spark plug, see T echnical data. Replacing the spark plug 1 Remov e the ignition cable shoe and clean around the spark plug. 2 Remov e the spark plug with a 3/4” (19 mm) spark plug sock e ...

  • Husqvarna 320 AWD - page 22

    22 – English Maintenance Checking the engine’ s cooling air intake Clean the air intake g rille in the engine cover behind the driver’ s seat. Open the engine cov er . Check that the cooling intak e is free from leav es, grass and dir t. Check the air duct, located on the inside of the engine co ver , ensure it is clean and does not rub again ...

  • Husqvarna 320 AWD - page 23

    English – 23 Maintenance 9 Hook up the height adjustment strut. 10 Secure the collet spring. 11 Fit the front cov er . Removing the cutting unit 1 Carr y out points 1-6 to put the cutting unit in the ser vice position, see Ser vice position f or the cutting unit. 2 Lower the cutting unit. 3 Open the unit catch. 4 Pull out the cutting unit. Checki ...

  • Husqvarna 320 AWD - page 24

    24 – English Maintenance Checking the cutting unit’ s parallelism Check the cutting unit’ s parallelism as f ollows: 1 Check the air pressure in the tyres 60 kP a/0.6 kp/cm 2 /8.5 PSI. 2 Place the machine on a flat surf ace. 3 Put the lifting le ver in the mo wing position. 4 Measure the distance between the ground and the front and rear edg ...

  • Husqvarna 320 AWD - page 25

    English – 25 Maintenance 7 Remov e the screws on the cutting co v er . Lift the unit frame and remov e the cutting unit cover . 8 Loosen the spring that tensions the V -belt and pr y off the belt. 9 Simply re verse the procedure to fit the ne w belt. Service position for the cutting unit The cutting head can be placed in the service position to ...

  • Husqvarna 320 AWD - page 26

    26 – English Maintenance Restoring fr om service position 1 Grip the front edge of the unit and loosen the lock, f old down and slide in the unit. 2 Replace the cutting height sta y and the belt. 3 T ension the belt with the belt adjuster . 4 Fit the front cov er . Checking the b lades W ARNING! W ear gloves to protect y our hands when working wi ...

  • Husqvarna 320 AWD - page 27

    English – 27 Lubrication Checking the engine’ s oil level. Check the oil le vel in the engine when the Rider stands horizontal with the engine s witched off. Open the engine cov er . Loosen the dipstick, pull it up and wipe it off . Now insert the dipstick again. The dipstick should be completely scre wed down Pull the dipstick out again and re ...

  • Husqvarna 320 AWD - page 28

    28 – English Lubrication Checking the transmission oil le vel 1 Remov e the transmission co ver . Undo the two screws (one on each side) and lift off the transmission cov er . 2 Check that there is oil in the tr ansmission’ s oil tank. Rider 318 Fill if necessary with engine oil SAE 10W/40 (class SF–CC). Rider 320 A WD Fill if necessary with ...

  • Husqvarna 320 AWD - page 29

    English – 29 T roub leshooting sc hedule Prob lem Procedure Engine does not start There is no fuel in the fuel tank Spark plug defectiv e F aulty spar k plug connections or interchanged cables Dir t in the carburettor or fuel line Star ter motor does not tur n ov er the engine Starter motor does not turn over the engine Batter y flat Bad contact ...

  • Husqvarna 320 AWD - page 30

    30 – English Storage Winter stora ge At the end of the season, or if the machine is going to stand idle f or more than 30 days , it should immediately be made ready f or storage. Fuel which is left to stand for long periods (30 da ys or more) can leav e tacky deposits which can b lock the carburettor and interf ere with the engine. Fuel stabilise ...

  • Husqvarna 320 AWD - page 31

    English – 31 TECHNICAL D A T A Note 1: The power r ating of the engine indicated is the av erage net output (at specified rpm) of a typical production engine for the engine model measured to SAE standard J1349/ISO1585. Mass production engines may differ from this v alue. Actual power output f or the engine installed on the final machine will de ...

  • Husqvarna 320 AWD - page 32

    32 – English TECHNICAL D A T A Cutting unit Combi 94 Combi 103 Combi 112 Cutting width, mm/inch 940/37 1030 / 41 1120 / 44.1 Cutting heights, 7 positions , mm/inch 25-75/0.98-2.95 25-75/0.98-2.95 25-75/0.98-2.95 Blade length, mm/inch 358/14.09 388/15.28 420 / 16,5 IMPOR T ANT INFORMA TION When the ser vice lif e of this product has been ser ved a ...

  • Husqvarna 320 AWD - page 33

    English – 33 TECHNICAL D A T A EC-declaration of conf ormity (Applies to Europe onl y) Husqvarna AB, SE-561 82 Huskv ar na, Sweden, tel.: +46-36-146500, hereby declares that Husqv ar na Rider 318 and Rider 320 A WD from 2010’ s serial numbers and onwards (the year is clearly stated in plain te xt on the rating plate with subsequent serial numbe ...

  • Husqvarna 320 AWD - page 34

    ...

  • Husqvarna 320 AWD - page 35

    ...

  • Husqvarna 320 AWD - page 36

    ´®z+VVr¶6(¨ 2011-11-16 ´®z+VVr¶6(¨ 1154548-26 Original instructions ...

Fabricant Husqvarna Catégorie Lawn Mower

Les documents que nous recevons du fabricant de l'appareilHusqvarna 320 AWD peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Husqvarna
- manuels d’utilisations 320 AWD
- fiches produit Husqvarna
- dépliants
- ou étiquettes-énergie Husqvarna 320 AWD
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Husqvarna 320 AWD.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Husqvarna 320 AWD, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Husqvarna 320 AWD. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Husqvarna 320 AWD.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Husqvarna 320 AWD, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Husqvarna 320 AWD par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Husqvarna 320 AWD.

Le manuel d’utilisation complet Husqvarna, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Husqvarna 320 AWD - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Husqvarna 320 AWD, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lHusqvarna 320 AWD qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Husqvarna 320 AWD - qui devraient nous aider dans les premières étapes lors de l'utilisation Husqvarna 320 AWD
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Husqvarna 320 AWD
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Husqvarna 320 AWD dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Husqvarna 320 AWD?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Husqvarna 320 AWD, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Husqvarna 320 AWD il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)