Français dropdown-ico

Manuel d’utilisation Datamax S-Class ST-3210

84 pages 2.02 mb
Télécharger

Aller à la page of 84

Summary
  • Datamax S-Class ST-3210 - page 1

    ST/SV 3210 & ST/SV 3306 Operator’s Manual ...

  • Datamax S-Class ST-3210 - page 2

    ...

  • Datamax S-Class ST-3210 - page 3

    CG Triumvirate is a trademark of Agfa Corporation. Copyright Information: Firmware (Software) Agreement The enclosed Firmware (Software) resident in the EPROM’s is owned by Licensor or its suppliers and is licensed for used only on a single printer in the user’s Trade or Business. The User agrees not to, and not to authorize or permit any other ...

  • Datamax S-Class ST-3210 - page 4

    ...

  • Datamax S-Class ST-3210 - page 5

    Agency Compliance and Approvals: C US Listed UL1950 Information Technology Equipment C22.2 No. 950-M93 EN60950 For 230 Volt Operation (Europe): Use a cord set, marked "HAR," consisting of a min H05VV-F cord which has a minimum 0.75 square mm diameter conductors, provided with an IEC 320 receptacle and a male plug for the country of instal ...

  • Datamax S-Class ST-3210 - page 6

    Important Safety Instructions: This printer has been carefully designed to give many years of safe and reliable performance; however, as with all types of electronic equipment, there are some basic precautions that should taken to avoid personal injury or damage to the printer: Ø Carefully read the installation and operating instructions provided ...

  • Datamax S-Class ST-3210 - page 7

    i Contents Printer Overview 1.0 About the Printer ........................................................... 1 1.0.1 Standard Features ........................................... 2 1.0.2 Optional Features ............................................ 3 Getting Started 2.0 Unpacking the Printer ................................................... 5 2 ...

  • Datamax S-Class ST-3210 - page 8

    ii 4.0.2 SV Model ....................................................... 23 4.1 Stock ID Selections ..................................................... 24 4.2 Start of Print & Cut/Tear Adjustment ........................... 26 4.3 Operational Database Modificatio n ............................. 27 4.3.1 Database Modification Example ........ ...

  • Datamax S-Class ST-3210 - page 9

    iii Warranty Information .................................................. 65 Glossary .......................................................................... 69 Index ................................................................................. 73 ...

  • Datamax S-Class ST-3210 - page 10

    iv ...

  • Datamax S-Class ST-3210 - page 11

    ST/SV-3210 and ST/SV-3306 1 Printer Overview 1.0 About the Printer ST ( Table ) Model SV (Vertical ) Model The ST-3210, SV-3210, ST-3306 and SV-3306 printers, hereafter referred to as ‘the printer’, blend rugged design with state-of-the-art electronics and user-friendly features to redefine industry printer standards. This printer is equipped w ...

  • Datamax S-Class ST-3210 - page 12

    2 ST/SV-3210 and ST/SV-3306 1.0.1 Standard Features This printer offers these standard features. Printing: Ø Direct Thermal printing Ø On-Demand and Batch printing modes Ø Automatic ticket loading and top of form positioning Ø 3.375” x 11.375” Interior Fan-Fold Ticket Stock Platform ( ST Models only ) Ø Integral Tearbar Ø Lockable Side Co ...

  • Datamax S-Class ST-3210 - page 13

    ST/SV-3210 and ST/SV-3306 3 1.0.2 Optional Features This printer offers these optional features. Cutter and Tray (ST Models only) : Ø A factory-installed device that will cut stock with a maximum thickness of .008 inch (.2 mm) and a minimum thickness of .0025 inch (.06 mm). The tray attaches to the front of the printer to collect cut tickets, and ...

  • Datamax S-Class ST-3210 - page 14

    4 ST/SV-3210 and ST/SV-3306 ...

  • Datamax S-Class ST-3210 - page 15

    ST/SV-3210 and ST/SV-3306 5 Getting Started 2.0 Unpacking the Printer Inspect the shipping container(s) for damage; if evident, notify the shipping carrier to report the nature and extent of the damage before proceeding. The printer is carefully packaged to avoid any damage during transit. In order to operate the printer, you will need to remove th ...

  • Datamax S-Class ST-3210 - page 16

    6 ST/SV-3210 and ST/SV-3306 2.0.1 Inspection After removing and inspecting the printer, check the remaining contents of the container. In addition to this manual, the following items should be included: Ø Ticket Printer Ø Power cord Ø Keys ( ST Models only ) Ø Accessories CD Ø Special or additionally purchased items. 2.0.2 Additional Requireme ...

  • Datamax S-Class ST-3210 - page 17

    ST/SV-3210 and ST/SV-3306 7 Setting up the Printer This section details the connections, loading methods, memory module installation, and resident ticket formats of the printer. 3.0 AC Voltage Configuration Depending upon the configuration of the AC Selection Switch and fuse, the printer is capable of either 115 or 230 VAC single-phase operation. B ...

  • Datamax S-Class ST-3210 - page 18

    8 ST/SV-3210 and ST/SV-3306 3.1 Interfacing the Printer Interfacing the printer to the host computer can be made through either a parallel or a serial cable (see Appendix C for cable requirements). Communication port selection is automatic: the first port to receive data is set ‘active’ by the printer. To change an active port, cycle the power ...

  • Datamax S-Class ST-3210 - page 19

    ST/SV-3210 and ST/SV-3306 9 Printer power and interface connections: Follow these instructions to connect the printer. Œ Turn ‘Off’ the power to the Host Computer. • Verify that the Printer’s AC Configuration has been set; see Section 3.0. Ž Connect the interface cable securely between the Printer and Host communication ports. • Verify ...

  • Datamax S-Class ST-3210 - page 20

    10 ST/SV-3210 and ST/SV-3306 3.2 Loading Ticket Stock Both printers feature an automatic ticket loading and positioning mechanism, although the initial loading instructions differ slightly according to model and options. 3.2.1 ST Models Œ Plug in and turn ‘On’ the printer. • Insert the Key and unlock the Access Cover. Ž Raise the Access Cov ...

  • Datamax S-Class ST-3210 - page 21

    ST/SV-3210 and ST/SV-3306 11 To use roll ticket stock , the stock must be mounted on the optional Roll Hanger, as shown. (See Section 6 for stock requirements.) þ Note: To use an internal fanfold ticket source on a printer equipped with the Roll Hanger option, first remove the Roll Hanger by unscrewing it from the printer. Store the hanger in a sa ...

  • Datamax S-Class ST-3210 - page 22

    12 ST/SV-3210 and ST/SV-3306 3.2.2 SV Models Œ Plug in and turn ‘On’ the printer. • Place fanfold ticket stock in the bottom of the enclosure, bring the stock up to the Media Guides. (The TOF Mark should be facing away from the Printhead Latch ; see Section 4.) Ensure that the Printhead Latch is locked. Ž Loosen the Thumbscrew and adjust th ...

  • Datamax S-Class ST-3210 - page 23

    ST/SV-3210 and ST/SV-3306 13 3.3 Installing a Memory Module Optional Flash Memory Modules offer convenient, non-volatile storage of formats, fonts and graphics. Refer to the DPL Programmer’s Manual (part number 88-2051-01) for programming and use details. To install a module : Œ Turn ‘Off’ the printer. • Place the Memory Module’s ‘writ ...

  • Datamax S-Class ST-3210 - page 24

    14 ST/SV-3210 and ST/SV-3306 3.4 Using the Front Panel The Front Panel on both models is comprised of a ticket exit, darkness control, three indicator lights, and three dual-purpose buttons. ST Models SV Models (Continued next page) ...

  • Datamax S-Class ST-3210 - page 25

    ST/SV-3210 and ST/SV-3306 15 Ticket Exit The printed tickets are expelled from this opening. Darkness Control The Darkness Control will adjust the darkness of the printing on the tickets: turning the control clockwise darkens the print and turning the control counterclockwise lightens the print. This darkness function can also be controlled through ...

  • Datamax S-Class ST-3210 - page 26

    16 ST/SV-3210 and ST/SV-3306 Power-Up and Off-Line Mode Button Functions (the On-Line Indicator is ‘Off’) Ø F2: Three functions: (a) Press momentarily to advance ticket stock , or to manually load ticket stock. (b) Press and hold during power-up to print a Configuration and Test Pattern Ticket, and enter Character Dump mode. (c) Press and hold ...

  • Datamax S-Class ST-3210 - page 27

    ST/SV-3210 and ST/SV-3306 17 3.5 Resident Formats Stored within the memory are several ticket formats that provide useful setup, operational, and problem diagnosis information. Load stock that is at least 2 inches (51 mm) wide to capture all the data on these resident formats. 3.5.1 Configuration Ticket The Configuration Ticket provides memory, fir ...

  • Datamax S-Class ST-3210 - page 28

    18 ST/SV-3210 and ST/SV-3306 3.5.2 Test Pattern Tick et The Test Pattern Ticket is a resident format that can be used to determine general print quality and the condition of the printhead. Œ With stock loaded, turn the printer ‘On’. • Press the PAUSE button to put the printer in the off-line mode. Ž Simultaneously press the F1 and F2 button ...

  • Datamax S-Class ST-3210 - page 29

    ST/SV-3210 and ST/SV-3306 19 3.5.3 Internal Test Ticket The Internal Test Ticket is another resident format that is another useful indicator of print quality . This ticket features various font sizes and barcodes (the sample below was printed using the ST-3210). To print an Internal Test Ticket: Œ With stock loaded, turn the printer ‘On’. • ...

  • Datamax S-Class ST-3210 - page 30

    20 ST/SV-3210 and ST/SV-3306 3.6 Resett ing the Printer There are two different reset levels possible for the printer: 3.6.1 Warm Reset To reset the printer and return to the on-line mode: Press the PAUSE button to go off-line and then press the F1 + F3 buttons simultaneously. 3.6.2 Factory Default Reset To return the printer to default database se ...

  • Datamax S-Class ST-3210 - page 31

    ST/SV-3210 and ST/SV-3306 21 Adjusting and Maintaining the Printer This section details important adjustments, settings and periodic maintenance requirements that will ensure optimum printer performance. 4.0 TOF Sensor Adjustment The TOF Sensor in the printer has two functions: (1) sensing the presence of ticket stock and (2) when using reflective ...

  • Datamax S-Class ST-3210 - page 32

    22 ST/SV-3210 and ST/SV-3306 4.0.1 ST Model TOF Sensor Adjustment Œ Insert the Key and unlock the Access Cover. • Raise the Access Cover. (For convenience, the cover may also be removed by sliding it forward and then off.) Ž Unlock the Printhead Latch and raise the Printhead Assembly . • Grasp the Slide and move it ‘in’ or ‘out’ accor ...

  • Datamax S-Class ST-3210 - page 33

    ST/SV-3210 and ST/SV-3306 23 4.0.2 SV Model TOF Sensor Adjustment Œ Unlock and raise the Printhead Assembly . • Grasp the TOF Sensor and move it ‘in’ or ‘out’ accordingly, to position the sensor underneath the TOF Mark and within a quiet zone area of the ticket stock . Ž Lower the Printhead Assembly and lock the Printhead Latch . • Re ...

  • Datamax S-Class ST-3210 - page 34

    24 ST/SV-3210 and ST/SV-3306 4.1 Stock ID Selections The printer maintains a selection of 10 user modifiable stock setups. Each setup defaults to a specific print width, start print position and cut/tear position, where: Ø The Print Width is the print distance across the ticket. Ø The Start of Print Position is the distance, measured in inches, f ...

  • Datamax S-Class ST-3210 - page 35

    ST/SV-3210 and ST/SV-3306 25 The table below lists the default settings, according to the printer model, for each Stock ID number . Stock ID Default Settings Print Width Stock ID 3210 Models 3306 Models Start of Print Position Cut/Tear Position* 0 3.15" (80.0 mm) 3.20" (81.3 mm) .07" (1.8 mm) .05" (1.3 mm) 1 3.15" (80.0 mm) ...

  • Datamax S-Class ST-3210 - page 36

    26 ST/SV-3210 and ST/SV-3306 4.2 Start of Print & Cut/Tear Adjustment If none of the preset Stock ID parameters meet the needs of your application, then the Start of Print (SOP) and Cut/Tear (C/T) Adjustments can be used to visually set the required positions. To begin: Œ If on-line, press the PAUSE button to place the printer off-line. • Pr ...

  • Datamax S-Class ST-3210 - page 37

    ST/SV-3210 and ST/SV-3306 27 4.3 Operational Database Modification The operational database for the printer , which contains the parser mode setting and other important printer parameters, can be changed using the front panel. To change the Operational Database settings: Œ If on-line, press the PAUSE button to place the printer off-line. • Press ...

  • Datamax S-Class ST-3210 - page 38

    28 ST/SV-3210 and ST/SV-3306 Operational Database: ST/SV-3210 Models Parameter Description Settings Stock ID Stock ID number 0-9 (see Section 4.1) Label (Ticket) Width Width of the ticket stock used for printing. 1.89 inches (48.0 mm) 2.04 inches (51.8 mm) 2.20 inches (55.9 mm) 2.36 inches (59.9 mm) 2.52 inches (64.0 mm) 2.67 inches (67.8 mm) 2.83 ...

  • Datamax S-Class ST-3210 - page 39

    ST/SV-3210 and ST/SV-3306 29 Operational Database: ST/SV-3306 Models Parameter Description Settings Stock ID Stock ID number 0-9 (see Section 4.1) Label Width Width of the ticket stock used for printing. 1.81 inches (46.0 mm) 1.92 inches (48.8 mm) 2.03 inches (51.6 mm) 2.14 inches (54.4 mm) 2.24 inches (56.9 mm) 2.35 inches (59.7 mm) 2.46 inches (6 ...

  • Datamax S-Class ST-3210 - page 40

    30 ST/SV-3210 and ST/SV-3306 4.3.1 Database Modification Example This section details the modification of an Operational Database parameter. The following example increases the printing speed parameter from 6 to 8 IPS on the ST-3210; however, using the same basic procedure, any of the parameters can be changed regardless of the printer model. ΠIf ...

  • Datamax S-Class ST-3210 - page 41

    ST/SV-3210 and ST/SV-3306 31 4.4 Maintenance Routine maintenance will ensure the optimum performance of the printer. The following table outlines the recommended cleaning intervals, while the items listed below will help do the job safely and effectively: • Isopropyl alcohol • Soft-bristle brush • Cotton swabs • Soapy water/mild detergent ? ...

  • Datamax S-Class ST-3210 - page 42

    32 ST/SV-3210 and ST/SV-3306 4.4.1 Cleaning the Printhead Declining print quality (i.e., dropouts, streaking, or smudging) is usually caused by a surface build-up of dirt on the printhead; see Section 3.5.2 for an example. Left unattended, this build-up can lead to permanent printhead damage. To clean: Œ Turn ‘Off’ and unplug the printer. • ...

  • Datamax S-Class ST-3210 - page 43

    ST/SV-3210 and ST/SV-3306 33 4.4.2 Cleaning the Platen Roller Print quality can decline if the platen roller becomes contaminated with paper dust, grit or adhesive. When this build-up is not removed, it can cause abrasive damage to the printhead. To clean the Platen Roller: Œ Turn ‘Off’ and unplug the printer. • ST Models: Raise the access c ...

  • Datamax S-Class ST-3210 - page 44

    34 ST/SV-3210 and ST/SV-3306 4.4.3 TOF Sensor Cleaning If the TOF Sensor becomes blocked with paper particles, Top of Form detection can be inconsistent or fail completely. To clean the sensor: Œ Turn ‘Off’ and unplug the printer. • ST Models: Raise the access cover ; see Section 3.2. Ž Slide the printhead latch to the unlocked position, ra ...

  • Datamax S-Class ST-3210 - page 45

    ST/SV-3210 and ST/SV-3306 35 4.4.4 Ticket Detect Sensor Cleaning The Ticket Detect Sensor initiates the auto-loading process by signaling the presence of ticket stock within the Media Guides. If the sensor becomes blocked with paper particles, ticket feeding problems can occur. To clean the sensor: Œ Turn ‘Off’ and unplug the printer. • ST M ...

  • Datamax S-Class ST-3210 - page 46

    36 ST/SV-3210 and ST/SV-3306 4.4.5 Interior Cleaning ST Models only: Ticket Compartment Cleaning During normal operation, paper particles from the ticket stock accumulate inside the printer. These particles can stick to the ticket and cause voids in the print, reducing print quality. To clean the interior of the printer: Œ Turn ‘Off’ and unplu ...

  • Datamax S-Class ST-3210 - page 47

    ST/SV-3210 and ST/SV-3306 37 Troubleshooting 5.0 Troubleshooting Tips This section addresses common problems and suggests solutions. While not all situations can be addressed, many suggestions may prove helpful; however, if a problem persists or is not covered in this text, contact Datamax Technical Support or a qualified service technician. þ Not ...

  • Datamax S-Class ST-3210 - page 48

    38 ST/SV-3210 and ST/SV-3306 If experiencing this problem… Try this solution… No Communications: Ÿ The parser mode setting between the printer and host may not match; reconfigure, see Section 4.3. Ÿ The communication parameters between the printer and host may not match; reconfigure to match, see Section 4.3. Ÿ The interface connection may b ...

  • Datamax S-Class ST-3210 - page 49

    ST/SV-3210 and ST/SV-3306 39 If experiencing this problem… Try this solution… After printing the ticket, the Fault Indicator lights: Ÿ If cutter equipped, this may indicate a cutter fault; call for service. Ÿ If not cutter equipped: a) Possible programming problem. b) Possible mechanical problem – try pressing the FEED button to clear the f ...

  • Datamax S-Class ST-3210 - page 50

    40 ST/SV-3210 and ST/SV-3306 If experiencing this problem… Try this solution… The printer does not print formats sent from the host, but the Fault Indicator remains off: • The parser mode setting between the printer and host may not match; reconfigure, see Section 4.3.1. • The communication parameters between the printer and host may not ma ...

  • Datamax S-Class ST-3210 - page 51

    ST/SV-3210 and ST/SV-3306 41 5.1 Hex Dump Mode The hex dump mode is a useful tool for diagnosing problems, including communication and programming syntax errors. This mode allows a comparison of input strings to output data. Repeatedly sending a format can uncover handshaking problems (identified by sections of missing data in the output string). T ...

  • Datamax S-Class ST-3210 - page 52

    42 ST/SV-3210 and ST/SV-3306 ...

  • Datamax S-Class ST-3210 - page 53

    ST/SV-3210 and ST/SV-3306 43 Specifications 6.0 Specifications Communications Character Set: ANSI ASCII Parallel Interface Port: Centronics  type 36-pin Serial Interface Port: RS-232c and RS-422; DB25 Baud Rates: 600, 1200, 2400, 4800, 9600, 19.2K and 38.4K Word Length and Parity: Selectable data format: 7-bit word with even parity, or 8-bit wor ...

  • Datamax S-Class ST-3210 - page 54

    44 ST/SV-3210 and ST/SV-3306 Environmental Operating Temperature: 40°F to 100°F (4°C to 38°C) Storage Temperature: 32°F to 120°F (0°C to 49°C) Humidity: 10% to 95% non-condensing Ventilation: Free air movement Dust: Non-conducting, non-corrosive Electromagnetic Radiation: Moderate RF fields can be tolerated Fonts/Barcodes (See Appendix B fo ...

  • Datamax S-Class ST-3210 - page 55

    ST/SV-3210 and ST/SV-3306 45 Mechanical Width: ST/SV-3210 ST/SV-3306 8.14 inches (20.7 cm) 8.05 inches (20.4 cm) Depth: ST/SV-3210 ST/SV-3306 14 inches (35.6 cm) 7.65 inches (19.4 cm) Height: ST/SV-3210 ST/SV-3306 10.5 inches (26.7 cm) 10.5 inches (26.7 cm) Weight: ST Models SV Models 22 pounds (10 kg) 18.8 pounds (8.46 kg) Top Plate: SV Models onl ...

  • Datamax S-Class ST-3210 - page 56

    46 ST/SV-3210 and ST/SV-3306 Print Engine (continued) Maximum Fields and Characters Per Ticket: 600 fields with 16,000 characters per ticket Tear Bar: Tear up/down DRAM Memory: Internal Module Size: Scalable Module Size: 4 MB 512 KB (default) 256 KB (default) EPROM Memory: 1 MB Ticket Stock Requirements Type: Fan-fold and roll (if option equipped) ...

  • Datamax S-Class ST-3210 - page 57

    ST/SV-3210 and ST/SV-3306 47 6.1 Approved Ticket Stocks For optimum print quality and maximum printhead life, Datamax recommends using a ticket stock from the following table. Contact a Datamax Media Representative at (407) 523-5650 with any questions regarding your specific application. Manufacturer Material Comment Ricoh 150 TLA 190 Best quality ...

  • Datamax S-Class ST-3210 - page 58

    48 ST/SV-3210 and ST/SV-3306 ...

  • Datamax S-Class ST-3210 - page 59

    ST/SV-3210 and ST/SV-3306 49 Appendix A ASCII Control Code Chart Char Dec Hex Char Dec Hex Char Dec Hex Char Dec Hex Ctrl @ NUL 0 00 32 20 @ 64 40 ` 96 60 Ctrl A SOH 1 01 ! 33 21 A 65 41 a 97 61 Ctrl B STX 2 02 “ 34 22 B 66 42 b 98 62 Ctrl C EXT 3 03 # 35 23 C 67 43 c 99 63 Ctrl D EOT 4 04 $ 36 24 D 68 44 d 100 64 Ctrl E ENQ 5 05 % 37 25 E 69 45 ...

  • Datamax S-Class ST-3210 - page 60

    50 ST/SV-3210 and ST/SV-3306 ASCII Control Code Chart (continued) Char Dec Hex Char Dec Hex Char Dec Hex Char Dec Hex Ç 128 80 á 160 A0 192 C0 Ó 224 E0 ü 129 81 í 161 A1 193 C1 ß 225 E1 é 130 82 ó 162 A2 194 C2 Ô 226 E2 â 131 83 ú 163 A3 195 C3 Ò 227 E3 ä 132 84 ñ 164 A4 196 C4 õ 228 E4 à 133 85 Ñ 165 A5 197 C5 Õ 229 E5 å 134 86 ...

  • Datamax S-Class ST-3210 - page 61

    ST/SV-3210 and ST/SV-3306 51 Appendix B Available Fonts and Barcodes All available character fonts and barcodes are listed below. The selections will differ depending upon the parser mode setting. Accordingly, use either the DPL Programmer’s Manual or the DTPL Programmer’s Manual for detailed information. DPL Fonts Fonts 0 through 8 use the sla ...

  • Datamax S-Class ST-3210 - page 62

    52 ST/SV-3210 and ST/SV-3306 The table below lists font sizes 0 – 8; the numbers indicate the number of dots. Font Number Height Width Spacing Font 0 751 Font 1 13 7 2 Font 2 18 10 2 Font 3 27 14 2 Font 4 36 18 3 Font 5 52 18 3 Font 6 64 32 4 Font 7 32 15 5 Font 8 28 15 5 DPL Font Samples Font 0: 96 characters, alphanumeric, upper and lower case. ...

  • Datamax S-Class ST-3210 - page 63

    ST/SV-3210 and ST/SV-3306 53 Font 4: 62 characters, alphanumeric, uppercase. Font 5: 62 characters, alphanumeric, uppercase. Font 6: 62 characters, alphanumeric, uppercase. Font 7: OCR-A, size I. Font 8: OCR-B, size III. ...

  • Datamax S-Class ST-3210 - page 64

    54 ST/SV-3210 and ST/SV-3306 Font 9: Internal CG Triumvirate  font . The point sizes are selected by the number in the bar code height. Larger point sizes can be obtained by increasing the height and width multipliers. þ Note: Point sizes 4 and 5 are only available on the ST/SV-3306. DTPL Fonts Font Number Font ID Font Size Box Size FONT 1 F1 5 ...

  • Datamax S-Class ST-3210 - page 65

    ST/SV-3210 and ST/SV-3306 55 DTPL Font Samples All fonts contain ASCII characters (32-127); they are listed below by Font ID. ...

  • Datamax S-Class ST-3210 - page 66

    56 ST/SV-3210 and ST/SV-3306 DPL Barcodes Uppercase alpha names will print barcodes with human readable interpretations; lowercase alpha names will print barcodes only. Font Barcode Type Length Checksum Valid Characters A 3 of 9 Varies No 0-9, A-Z, -. *$/+% and space char. B UPC-A 11 digits Yes 0-9 C UPC-E 6 digits Yes 0-9 D Interleaved 2 of 5 Vari ...

  • Datamax S-Class ST-3210 - page 67

    ST/SV-3210 and ST/SV-3306 57 DPL Bar Code Samples Bar Code A: Code 3 of 9 Bar Code B: UPC-A Bar Code C: UPC-E Bar Code D: Interleaved 2 of 5 Bar Code E: Code 128 Bar Code F: EAN-13 Bar Code G: EAN-8 Bar Code H: Health Industry Bar Code (HBIC) ...

  • Datamax S-Class ST-3210 - page 68

    58 ST/SV-3210 and ST/SV-3306 Bar Code I: Codabar Bar Code J: Interleaved 2 of 5 w/module 10 checksum Bar Code K: Plessey Bar Code L: Interleaved 2 of 5 w/module 10 checksum and shipping bearer bars Bar Code M: 2 Digit UPC addendum Bar Code N: 5 Digit UPC addendum Bar Code O: Code 93 Bar Code p: Postnet ...

  • Datamax S-Class ST-3210 - page 69

    ST/SV-3210 and ST/SV-3306 59 Bar Code Q: UCC/EAN Code 128 Bar Code R: UCC/EAN Code 128 KMART NON EDI Bar Code S: UCC/EAN Code 128 Random Weight Barcode T: Telepen Barcode u: UPS MaxiCode ...

  • Datamax S-Class ST-3210 - page 70

    60 ST/SV-3210 and ST/SV-3306 Barcode v: FIM Barcode z: PDF-417 DTPL Barcodes Code 39; Code 128 A, B, and C; Codabar, Interleaved 2 of 5; UPC-A; EAN-8; and EAN-13. ...

  • Datamax S-Class ST-3210 - page 71

    ST/SV-3210 and ST/SV-3306 61 Appendix C Cable Listings Parallel Cable : Connect a Centronics  type 36-pin cable. Serial Cable : Connect a cable that complies with one of the configurations listed in the table below ( the serial interface cable must have specific connections [pin-outs] for proper data exchange) . The cable part numbers and sugges ...

  • Datamax S-Class ST-3210 - page 72

    62 ST/SV-3210 and ST/SV-3306 ...

  • Datamax S-Class ST-3210 - page 73

    ST/SV-3210 and ST/SV-3306 63 Appendix D SV Model Mounting Dimensions Top Plate Dimensions : ...

  • Datamax S-Class ST-3210 - page 74

    64 ST/SV-3210 and ST/SV-3306 Side Dimensions : ...

  • Datamax S-Class ST-3210 - page 75

    ST/SV-3210 and ST/SV-3306 65 Warranty Information ST-3210, SV-3210, ST-3306, and SV-3306 Datamax Barcode Products Limited Warranty Statement Printer Datamax warrants* to Purchaser that under normal use and service, the S-Class Ticket Printers, (with the exception of the thermal printhead, belts and platen roller ) purchased hereunder shall be free ...

  • Datamax S-Class ST-3210 - page 76

    66 ST/SV-3210 and ST/SV-3306 Warranty Service Procedures If a defect should occur during the warranty period, the defective unit shall be returned, freight and insurance prepaid, in the original shipping containers, to one of the following locations: Datamax Corporate Headquarters 4501 Parkway Commerce Boulevard Orlando, Florida 32808 USA Datamax I ...

  • Datamax S-Class ST-3210 - page 77

    ST/SV-3210 and ST/SV-3306 67 Limitation of Liability In no event shall Datamax be liable to the purchaser for any indirect, special or consequential damages or lost profits arising out of or relating to Datamax’s products, or the performance or a breach thereof, even if Datamax has been advised of the possibility thereof. Datamax’s liability, i ...

  • Datamax S-Class ST-3210 - page 78

    68 ST/SV-3210 and ST/SV-3306 ...

  • Datamax S-Class ST-3210 - page 79

    ST/SV-3210 and ST/SV-3306 69 Glossary alphanumeric Consisting of alphabetic, numeric, punctuation and other symbols. backup speed The speed at which the ticket stock is moved backward under the printhead following tear-off or cutting to position the next ticket at the start of print position. barcode A representation of alphanumeric information in ...

  • Datamax S-Class ST-3210 - page 80

    70 ST/SV-3210 and ST/SV-3306 DPI (dots per inch) A measurement of resolution, rated in the number of thermal elements contained in one inch of the printhead. Also referred to as print density. DPL ™ (Datamax Programming Language) Programming commands used specifically for formatting and production in Datamax printers. DTPL (Datamax Ticket Program ...

  • Datamax S-Class ST-3210 - page 81

    ST/SV-3210 and ST/SV-3306 71 reflective (TOF) mark A black strip on the underside of the ticket stock used to signal the top of form. roll hanger A device in the printer used to support rolled tickets . rolled tickets Ticket stock that is wound upon cardboard cores. slew speed The speed at which the ticket stock is moved under the printhead in non- ...

  • Datamax S-Class ST-3210 - page 82

    72 ST/SV-3210 and ST/SV-3306 ...

  • Datamax S-Class ST-3210 - page 83

    ST/SV-3210 and ST/SV-3306 73 Index A AC voltage configuration, 7, 37 access cover, 10 alphanumeric, 69 ASCII, 41, 49 B backup speed, 20, 28, 29, 69 barcodes , 44, 56 - 60, 69 baud rate, 8, 28, 29, 43 buttons, 14, 15, 43 C character set, 20, 43, 69 checksum, 56 , 69 cleaning, 31 - 36, configuration ticket, 17, 20, core diameter, 46, 69 cut/tear posi ...

  • Datamax S-Class ST-3210 - page 84

    74 ST/SV-3210 and ST/SV-3306 operational database, 15, 16, 24, 27 - 30 P parallel cable, 61 parallel interface port, 8, 43 parity, 8, 28, 29, 43 parser mode setting, 17, 20, 27, 40, 51 perforation, 26, 70 platen roller, 31, 33 print quality, 18, 19, 32, 33, 36, 38, 47 print speed, 20, 28 - 30, 38, 45, 47, 70 print width, 20, 24, 25, 45 printhead as ...

Fabricant Datamax Catégorie Printer

Les documents que nous recevons du fabricant de l'appareilDatamax S-Class ST-3210 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Datamax
- manuels d’utilisations S-Class ST-3210
- fiches produit Datamax
- dépliants
- ou étiquettes-énergie Datamax S-Class ST-3210
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Datamax S-Class ST-3210.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Datamax S-Class ST-3210, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Datamax S-Class ST-3210. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Datamax S-Class ST-3210.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Datamax S-Class ST-3210, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Datamax S-Class ST-3210 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Datamax S-Class ST-3210.

Le manuel d’utilisation complet Datamax, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Datamax S-Class ST-3210 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Datamax S-Class ST-3210, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lDatamax S-Class ST-3210 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Datamax S-Class ST-3210 - qui devraient nous aider dans les premières étapes lors de l'utilisation Datamax S-Class ST-3210
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Datamax S-Class ST-3210
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Datamax S-Class ST-3210 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Datamax S-Class ST-3210?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Datamax S-Class ST-3210, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Datamax S-Class ST-3210 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)