Manuel d’utilisation Diamond Audio Technology D3 400.2

12 pages 3.02 mb
Télécharger

Aller à la page of 12

Summary
  • Diamond Audio Technology D3 400.2 - page 1

    D3 400.2 | D3 500.4 | D3 600.1 | D3 1000.1 AMPLIFIER INST ALL A TION MANUAL ...

  • Diamond Audio Technology D3 400.2 - page 2

    2 Congratulations! Thank you for choosing a Diamond Audio T echnologies D3 Series amplier . We sincerely believe that DAT products offer you outstanding per- formance and value. DA T products ar e engineer ed and produced with the highest quality materials and incorporate the latest technology . We think you will nd your new DA T amplier m ...

  • Diamond Audio Technology D3 400.2 - page 3

    3 Fr equency Response: 20Hz to 20KHz +/-3 dB Signal to Noise Ratio: > 95dBA (20 to 20kHz) Channel Separation 50dB THD+N(T otal Harmonic Distortion + Noise) < 0.2% (Output-1W 4 Ohms) RCA Input Sensitivity: 150mV to 4V RCA Input Impedance: > 20K Ohms Min to Max V oltage requir ements 10.2V to 15.5V DC High/Low Pass Cr ossover: 12dB/Oct, 30-5 ...

  • Diamond Audio Technology D3 400.2 - page 4

    4 Connections and Contr ols This section describes how all of the terminals and adjustments of DA T D3 Series ampliers function. D3 400.2 2-Channel Amplifier 218 x 57.5mm D3.400.2 D3.600.1 D3.500.4 D3.1000.1 25A 25A 30A 30A 25A 25A 25A 30A 30A 30A 30A 0dB +12dB 0dB +12dB L R L R GAIN MIN MAX BASS BOOST 0dB +12dB HPF 30Hz BASS BOOST 0dB +12dB PH ...

  • Diamond Audio Technology D3 400.2 - page 5

    5 RCA Input and Pass-Thru Output - These RCA jacks allow for a normal Left and Right channel signal input. Simply connect to the source unit using RCA type audio cables, keeping them away from power wiring wherever possible. On the 4 channel amplifiers (D 3 500.4) “F ront” and “Rear” input jacks are present as well as a “Pass-Thru” out ...

  • Diamond Audio Technology D3 400.2 - page 6

    6 Installation Guidelines T ools and Supplies Listed bel ow ar e the tools and supplies needed to compl ete this installation: • V olt/Ohm Meter • Wir e strippers and wir e cutters • #2 Phillips scr ewdriver • Battery post wr ench • Hand held drill w/assorted bits • High quality electric al tape or heatshrink tubing • Soldering ir on ...

  • Diamond Audio Technology D3 400.2 - page 7

    7 Mounting Locations Engine Compartment Never mount this unit in the engine c ompartment. Mounting the unit in the engine compartment will void your warranty . T runk Mounting Mounting the amplier v ertically will pr ovide adequate cooling of the amplier . If you will be mounting it t o an existing panel, be sur e it’ s not prone to e xces ...

  • Diamond Audio Technology D3 400.2 - page 8

    8 3) T rim the power cable within 18 inches (45.7mm) of the positive battery post and splice in a in-line fuse holder . DO NOT install the fuse at this time. 4) Strip 1/2 inch (12.7mm) from the battery end of the power cable and crimp a large ring terminal to the cabl e. Connect the ring terminal to the positive (+) battery post. 5) Pr epar e the g ...

  • Diamond Audio Technology D3 400.2 - page 9

    9 25A 25A 25A FUSE REM GND +12V BRIDGE L R – – + + + – Connecting Multiple Speak ers If you must connect more than one speaker per channel, there are two methods in which to do so: Series or Parallel. Parall el connections are harder on the amplier than series connections, as the total impedance is lower compared to driving a single speake ...

  • Diamond Audio Technology D3 400.2 - page 10

    10 Installing the Remote Le vel Controll er The D3 600.1 and the D3 1000.1 come packaged with a r emote level contr ol. This allo ws you t o control the le vel by attenuating the amplitude or increasing (up to the maximum set-point) of the amplier’ s input gain control. This contr ol does not add additional bass boost, it simpl y allows y ou t ...

  • Diamond Audio Technology D3 400.2 - page 11

    11 Adjustment of Built-In Crosso ver (All Models) Placing the switch in the HP position sets the amplier to the High P ass mode, enabling fr equencies above the cutoff point t o pass. Placing the switch in the LP position sets the amplier to the Low Pass mode, enabling frequencies below the cut off point to pass. Placing the switch in the OFF ...

  • Diamond Audio Technology D3 400.2 - page 12

    041807 Diamond Audio W arranty Diamond Audio T echnologies, LLC (DA T) warrant s this product to be free fr om defect s in mate- rial and workmanship f or a period of one (1) year from the original date of pur chase pr ovided it was pur chased from an authorized DA T ret ailer within the United States. Ho wever, if this pr oduct was install ed by a ...

Fabricant Diamond Audio Technology Catégorie Stereo Amplifier

Les documents que nous recevons du fabricant de l'appareilDiamond Audio Technology D3 400.2 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Diamond Audio Technology
- manuels d’utilisations D3 400.2
- fiches produit Diamond Audio Technology
- dépliants
- ou étiquettes-énergie Diamond Audio Technology D3 400.2
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Diamond Audio Technology D3 400.2.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Diamond Audio Technology D3 400.2, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Diamond Audio Technology D3 400.2. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Diamond Audio Technology D3 400.2.

Manuel d’utilisation complet de l’appareil Diamond Audio Technology D3 400.2, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Diamond Audio Technology D3 400.2 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Diamond Audio Technology D3 400.2.

Le manuel d’utilisation complet Diamond Audio Technology, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Diamond Audio Technology D3 400.2 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Diamond Audio Technology D3 400.2, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lDiamond Audio Technology D3 400.2 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Diamond Audio Technology D3 400.2 - qui devraient nous aider dans les premières étapes lors de l'utilisation Diamond Audio Technology D3 400.2
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Diamond Audio Technology D3 400.2
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Diamond Audio Technology D3 400.2 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Diamond Audio Technology D3 400.2?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Diamond Audio Technology D3 400.2, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Diamond Audio Technology D3 400.2 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (0)