Français dropdown-ico

Manuel d’utilisation GenTran ATS1001R

36 pages 2.37 mb
Télécharger

Aller à la page of 36

Summary
  • GenTran ATS1001R - page 1

    OVATION™ Series Automatic Transfer Switch Systems Installation, Operating and Maintenance Instructions For Models: • ATS1001D, ATS1001R • ATS2001D, ATS2001R • ATS2002R Model ATS1001D Model ATS1001R Model ATS 2001D Model ATS2001R Model ATS2002R NOTE TO INSTALLER: Please leave this manual with the customer for future reference. Una versión e ...

  • GenTran ATS1001R - page 2

    2 This manual is published for informational pur poses and should not be considered all inclusive. If fu rther information is requ ired, you should consult Gen/Tran Corporation. S ale of product shown in this document is subject to terms and conditions outlined in appropriate Gen/Tran selling policies or othe r contractual agreement between the par ...

  • GenTran ATS1001R - page 3

    3 TABLE OF CONTENTS SECTION 1 - INTRODUCTION ............................................................................................................................... ......... 4 1.1 General Description ............................................................................................................................... 4 1.2 Standar ...

  • GenTran ATS1001R - page 4

    4 SECTION 1 - INTRODUCTION 1.1 General Description The OVATION™ Series Automatic Transfer Sw itch (ATS) system, used in conjunction with a standby generator, provi des a convenient, economical way to maintain po wer in a home or business during a utility ou tage. The transfe r switch senses when utility power is lost, starts a permanently install ...

  • GenTran ATS1001R - page 5

    5 1.2 Standard Configurations: TABLE 1.2 Model ATS1001D ATS1001R ATS2001D ATS2001R ATS2002R # Circuits (1 Pole) 14 16 38 38 4 Enclosure Type NEMA 1 NEMA 3R NEMA 1 NEMA 3R NEMA 3R GENERATOR Main 100 A, 2 Pole 100 A, 2 Pole 125 A, 2 Pole 125 A, 2 Pole 200 A, 2 Pole UTILITY Main 100 A, 2 Pole 100 A, 2 Pole 200 A, 2 Pole 200 A, 2 Pole 200 A, 2 Pole Max ...

  • GenTran ATS1001R - page 6

    6 RETROFIT: NEW CONSTRUCTION OR RETROFIT 1.4 How the OVATION™ Series Automatic Transfer Switc h Works: 1) When the utility power fails or drops below 190 volt s or 54 Hz or exceeds 280 volts or 66 Hz, the OVATION™ Automatic Transfer Switch will begin the generator starting seque nce after a 5-second delay. 2) Once the generator is started, the ...

  • GenTran ATS1001R - page 7

    7 3) The transfer switch will automatically monitor if the generator ha s sufficient available capacity to operate any or all applian ces connected to PowerPause™ Load Management modules, starting with p riority 1 Load, based upon appliance power requirements “learned” from a setup utility a t the time of the transfer switch installati on. On ...

  • GenTran ATS1001R - page 8

    8 1.5 Key Components: (continued) * Supplied with optional PowerPau se™ Load Management Module (Model LSM) ** Not shown: ATSRK Relay Kit Control Module Generator Main 200 Am p Drive Motor Assembl y Neutral Bar Ground Bar [ Circuit Breaker Spaces - 4] To Set Generator Size To Set Exercise Schedule Model ATS2002R** Actuator Current Transformers* ( ...

  • GenTran ATS1001R - page 9

    9 1.5 Key Components: (continued) * Supplied with optional PowerPause™ Load Managem ent Module (Model LSM) ** Not shown: ATSRK Relay Kit 1.5.1 User Interface Display (UID) The User Interface Display (UID), programming set switches and LEDs provide inform ation about the transfer switch, generato r an d utility status. This UID is also used fo r p ...

  • GenTran ATS1001R - page 10

    10 1.5.5 Remote PowerPause™ Relay Box (Optional) The PowerPause ™ Relay Box can control up to two 2-Pole (2 40VAC) 30A or 50A loads by interrupting power to the load when commanded by the Po werPause ™ Load Management Module, thereby preventing overloading the standby generator. Pack aged in a NEMA 3R enclosure, the PowerPause ™ Relay Box c ...

  • GenTran ATS1001R - page 11

    11 SECTION 2 – COMPATIBLE EQUIPMENT 2.1 Compatible Generators In order for the OVATION™ Series ATS to function as designed, it must be connected t o a permanently installed, automatic s tarting generator, with a continuous supply of fuel, suc h as gasoline, diesel, LPG or natural gas. Additionally, gasoline or diesel-pow ered generators must be ...

  • GenTran ATS1001R - page 12

    12 SECTION 3 – PREPARING FOR INSTALLATION ALL Gen/Tran OVATION™ Series ATS systems shoul d be installed by a professional licensed electrician familiar with electrical wi ring and codes, and experienced in working with generators. Gen/Tran accepts no responsibility for a ccidents caused by incorrect and/or improper installation. OVATION™ Seri ...

  • GenTran ATS1001R - page 13

    13 2) Your Installer will determine if all of the desired back-up loads can be operate d by the generator at the same time. If not, y ou will need to purchase/install PowerPause™ Load Management modules to manage pre-determined loads so as to not exceed the generator capacity. 3) If PowerPause™ Load Management modules are required, de term ine ...

  • GenTran ATS1001R - page 14

    14 Examples of critical loads that are NOT recomme nded (NOT OK) to be connected to the Po werPause ™ Load Management Module and Relay Box are: • Refrigerators and freezers • Aquariums • Central heating systems (gas, oil, electric) • Furnace fan (air handler) • Sump pumps • Septic lift pumps • Pool and spa anti-freeze pumps • Medi ...

  • GenTran ATS1001R - page 15

    15 SECTION 4 – INSTALLATION AND WIRING Extreme care should be taken to protect the transfer sw itch from drill chips, fillings, and ot her contaminants when making the cable entry holes and m ounting the enclosure to prevent com ponent damage or a future malfunction. This device should be installed in accordance with all loca l codes, standards a ...

  • GenTran ATS1001R - page 16

    16 INTERNAL WIRING DIAGRAMS MODELS ATS2001D/R: Diagram 4.2 ...

  • GenTran ATS1001R - page 17

    17 INTERNAL WIRING DIAGRAMS MODEL ATS2002R: Diagram 4.3 ...

  • GenTran ATS1001R - page 18

    18 4.1 Standard Mounting Proced ures 4 .1.1. As Service Equipment and/or primary Load Cent er Panel: Models ATS1001D/R, ATS20 01D/R or ATS2002R: When using the transfer switch as Service Entrance Equipment, m ount the OVATION™ Series ATS as close as possible to the utility meter. NOTE on Models ATS1001R, ATS2001R and ATS2002R only (NEMA Type 3R e ...

  • GenTran ATS1001R - page 19

    19 4.1.2. As a Generator subpanel: Models ATS1001D/R : If using the Ovation™ Series ATS as a generator sub panel, mount th e transfer switch as close to the load center as possible. The OVATION™ ATS can be installed on either the left or right side of the load center. If flush-m ounting is desired, the OVATION™ A TS can be mounted in the adja ...

  • GenTran ATS1001R - page 20

    20 4.2 Mounting Procedure for Two Load Centers When the main service is 400A or more and/or 2 or more load centers will be installed, dedicate one load center to non-emergenc y loads (not connected to generator po wer) and the 2 nd load center as an OVATION™ Model 1001 or 2001D/R load center/transfer switch for generator back-up circuits. Follow ...

  • GenTran ATS1001R - page 21

    21 NOTE: Not all generators require four co ntrol wires to operate. Some may combine the CRANK and ON function in which case the CRANK wire is not required. Additionally, select generators ar e controlled by a 240VAC signal fro m the transfer switch. If you need assistance with your particular generator-trans fer switch contro l connection, contact ...

  • GenTran ATS1001R - page 22

    22 7. Re-plug cables to Control Module remove in step 2 and PowerPause connec tor to PowerPause Modules. 8. Re-install Control Module into transfer switch. a. Line up Control Module to breaker bus stabs from where rem oved in step 1. b. Hold at 30° angle, push onto bus stabs c. Lower outside end flush with enclosure. d. Slide Control Module ½” ...

  • GenTran ATS1001R - page 23

    23 SECTION 5 – PROGRAMMING THE SYSTEM 5.1 Setting Generator Size If PowerPause™ Load Manag ement Modules are not in stalled, dial should be set t o 25Kw. (Factory default setting is 25Kw). NOTE: Setting dial to 25Kw disab les all power management fun ctions even if PowerPause™ L oad Management Modules are installed. If any PowerPause™ Load ...

  • GenTran ATS1001R - page 24

    24 5.4 User Interface Display/Control Module Functions Each OVATION™ ATS User Interface Display has five (5) buttons th at program and control t he automatic transfer switch and contro l certain generator functions. NOTE: The gener ator may also have c ontrols that program certai n generator features that are N OT programmable from the OVATION™ ...

  • GenTran ATS1001R - page 25

    25 SECTION 6 –STARTUP AND TES TING Voltages within the transfer switch en closure present a shock hazard that can cause severe personal inj ury or death. Use extreme caution to avoid touching elect rical contacts when the cabinet door is open or r emoved. Do not wear jewelry or loo se clothing. Stand on a dry, non-conductive su rface such as a ru ...

  • GenTran ATS1001R - page 26

    26 (i.e. air conditioning compressor and air handle r fan), turn ON all branch circui t breakers for managed load. For installer safety, 1 lighting circuit may be left ON to illuminate the tra nsfer switch installation and/or egress areas. c. Turn ON all appliances managed by a PowerPause™ Load Managem ent Module. For air conditioning systems, se ...

  • GenTran ATS1001R - page 27

    27 SECTION 7 – TROUBLESHOOTI NG Use the following troubleshooting guide t o help diagnose transfer switch problems. Thorough ly inspection transfer switch wirin g and cable connections. Correct wiring problems before per forming any tests or replacing any components. 7.1 Basic T roubleshoo ting In case of generator failure, check the following BE ...

  • GenTran ATS1001R - page 28

    28 E. Ge nset d oes not exercise, or exercises, but does not transfer loads 1. Exercise programming incorrect 2.Genset exercise not frequent enough 3. Genset is in MANUAL mode 4. Genset cranks but does not start 5. Genset does not crank 6. No start signal from transfer switch 7. Controller module may be def ective 8. TRANSFER during exercise set to ...

  • GenTran ATS1001R - page 29

    29 SECTION 8 – MAINTENANCE AND SERVICE 8.1 Maintenance To ensure that the generator will always be rea dy when required, it is important to start and exercise the gener ator regularly and keep the fuel tank filled with fresh fuel IF GASOLINE OR DIESEL. From the factory, the OVATION™ transfer switch will automatically perform the exercise progra ...

  • GenTran ATS1001R - page 30

    30 Model ATS1001D, -22 MODEL ATS1001D, -22 If your model ends in -22, order replaceme nt ITEM ending in -22 if shown. ITEM QTY PART# DESCRIPTION TYPE 2 2 17729 End pad, polystyren e, 7/18/1.375, not shown A 3 2 32403 Screw, 8-32x.3/8, Hex, Type F, steel, zinc C 4 1 37012 Nut, Nylock, 8 -32, zinc plated C 5 1 50104 Clip, interlock B 6 1 50131 Interl ...

  • GenTran ATS1001R - page 31

    31 Model ATS1001R, -22 MODEL ATS1001R, -22 If your model ends in -22, order replaceme nt ITEM ending in -22 if shown. ITEM QTY PART# DESCRIP TION TYPE 1 4 17728 Corner pad, polystyrene, 5.75x5.75x6.875, not shown A 2 1 50508 Screwdriver, Mini, .100 straight blade, GT logo, not shown A 3 2 S7956W Label, Date code, .4375x.75, white, no t shown A 5 1 ...

  • GenTran ATS1001R - page 32

    32 Model ATS2001D ITEM QTY PART. DESCRIPTION SOURCE 1 1 17727 Carton, 18.25x7.125x42.687, 5PF-FOL, not shown A 2 4 27484 Hollow Corner pad, polystyrene, 5.75x5.75x6.8, not sh own A 3 2 32400 Screw, 6-32x.5, Hex, Type F, steel, zinc C 4 2 32403 Screw, 8-32x.3/8, Hex, Type F, steel, zinc C 5 1 50232 Circuit breaker 200A, 2 pole, MBK, 10K AIC B 6 1 50 ...

  • GenTran ATS1001R - page 33

    33 Model ATS2001R ITEM QTY PART NO. DESCRIPTION SOURCE 1 1 17727 Carton, 18.25x7.125x42.687, 5PF-FOL, not shown A 2 4 17728 Corner pad, polystyren e, 5.75x5.75x6.875, not shown A 3 1 17729 End pad, polystyren e,7/18/1.375, not shown A 4 1 50232 Circuit breaker 200A, 2 pole, MBK, 22K AIC B 5 1 50478 Label, carton, ATS Ovation™, 2001R, not shown A ...

  • GenTran ATS1001R - page 34

    34 Model ATS2002R, -22 ITEM QTY PART DESCRIPTION SOURCE 1 4 17728 Corner pad, polystyren e, 5.75x5.75x6.87, not shown A 2 2 29880 Screw, 10-32x.5, RHPS, steel, zinc C 3 1 32390 Screw, 8-32x.75, Hex, thread cutting, steel, zi nc C 4 8 32403 Screw, 8-32x.3/8, Hex, Type F, steel, zinc C 5 4 32438 Screw, 10-32x.375, Type 23, Hex, steel, zinc C 6 1 5051 ...

  • GenTran ATS1001R - page 35

    35 OPTIONAL ITEMS FOR YOUR OVATION™ ATS – AVAILABLE FROM GENTRAN CORPORATION: PART NUMBER DESCRIPTION LSM PowerPause™ Load Management Mod ule Kit with Current sense cable For up to 2 x 240V circuits up to 50 amps (or 4 x 120V circuits) PP30-1 PowerPause™ Relay Box, 30 Amp, 1 circuit, 240 VAC. Includes 1 relay PP30-2 PowerPause™ Relay Box, ...

  • GenTran ATS1001R - page 36

    36 Gen/Tran Corporation P.O. Box 1001 Alpharetta, GA 30009 Toll free: 1-888-GEN-TRAN Fax: 770-552-7756 www.gen-tran.com Customer Service Hours: 8:00 a.m. until 5:00 p.m. Eastern Time, Monday – Friday 07/16/10 PN 530001 Rev D © Copyright 2008-2010 Gen-Tran Corporation. All rights rese rved. GenTran and the Gen Tran Logo are register ed trademarks ...

Fabricant GenTran Catégorie Switch

Les documents que nous recevons du fabricant de l'appareilGenTran ATS1001R peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques GenTran
- manuels d’utilisations ATS1001R
- fiches produit GenTran
- dépliants
- ou étiquettes-énergie GenTran ATS1001R
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation GenTran ATS1001R.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation GenTran ATS1001R, manuels d’entretien, brefs manuels ou manuels de l’utilisateur GenTran ATS1001R. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit GenTran ATS1001R.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil GenTran ATS1001R, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser GenTran ATS1001R par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs GenTran ATS1001R.

Le manuel d’utilisation complet GenTran, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel GenTran ATS1001R - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières GenTran ATS1001R, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lGenTran ATS1001R qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil GenTran ATS1001R - qui devraient nous aider dans les premières étapes lors de l'utilisation GenTran ATS1001R
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de GenTran ATS1001R
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service GenTran ATS1001R dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de GenTran ATS1001R?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec GenTran ATS1001R, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec GenTran ATS1001R il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)