Français dropdown-ico

Manuel d’utilisation Hearth and Home Technologies RCOR-HVB-IPI

41 pages 2.29 mb
Télécharger

Aller à la page of 41

Summary
  • Hearth and Home Technologies RCOR-HVB-IPI - page 1

    1 Models: Pier-HVB-IPI ST -HVB-IPI LCOR-HVB-IPI RCOR-HVB-IPI Underwriters Laboratories Listed This product is covered by one or more of the following patents: (United S tates) 4,1 12,913; 4,408,594; 4,422,426; 4,424,792; 4, 520,791; 4,793,322; 4,852,548; 4,875,464; 5,000,162; 5,016,609; 5,076,254 5,191,877; 5,218,953; 5,328,356; 5,429,495; 5,452,70 ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 2

    2 These units MUST use one of the vent systems described in the Installing the Fireplace section of the Installers Guide . NO OTHER vent systems or component s MA Y BE USED . This gas fireplace and vent assembly MUST be vented directly to the outside and MUST NEVER be attached to a chimney serving a separate solid fuel burning appliance. Each gas a ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 3

    3 Safety and W arning Information .................................................. 2 Service Parts List ......................................................................... 4 Approvals and Codes ................................................................ 13 Appliance Certification ........................................................ ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 4

    4 * Part number list on following page. * La liste des numéros de pièce se trouve à la page suivante. 5 Log Assembly (NG , LP) Exploded Part s Diagram (GN, PL) Vue éclatée des pièces Service Parts List Pier-HVB-IPI Beginning Manufacturing Date: 6-03 Ending Manufacturing Date: ______ 2 1 3 4 6 7 8 9 10 ! 11 12 ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 5

    5 (NG , LP) Exploded Part s Diagram / V ue éclatée des pièces IMPORT ANT : THIS IS DA TED INFORMA TION. The most current information is located on your dealers VIP site. When ordering, supply serial and model numbers to ensure correct service part s. / IMPORT ANT : L'information fournie dans cette brochure n'est valide que pendant une ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 6

    6 (NG , LP) Exploded Parts Diagram (GN, PL) Vue éclatée des pièces Service Parts ST -HVB-IPI Beginning Manufacturing Date: 6-03 Ending Manufacturing Date: ______ * Part number list on following page. * La liste des numéros de pièce se trouve à la page suivante. 4 Log Assembly 2 3 1 6 5 7 ! 8 ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 7

    7 (NG , LP) Exploded Part s Diagram / V ue éclatée des pièces IMPORT ANT : THIS IS DA TED INFORMA TION. The most current information is located on your dealers VIP site. When ordering, supply serial and model numbers to ensure correct service part s. / IMPORT ANT : L'information fournie dans cette brochure n'est valide que pendant une ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 8

    8 * Part number list on following page. * La liste des numéros de pièce se trouve à la page suivante. 5 Log Assembly (NG , LP) Exploded Parts Diagram (GN, PL) Vue éclatée des pièces Service Parts LCOR-HVB-IPI Beginning Manufacturing Date: 6-03 Ending Manufacturing Date: ______ 6 2 3 4 7 8 1 9 10 ! 11 12 ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 9

    9 (NG , LP) Exploded Parts Diagram / V ue éclatée des pièces IMPORT ANT : THIS IS DA TED INFORMA TION. The most current information is located on your dealers VIP site. When ordering, supply serial and model numbers to ensure correct service p arts. / IMPORT ANT : L'information fournie dans cette brochure n'est valide que pendant une c ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 10

    10 * Part number list on following page. * La liste des numéros de pièce se trouve à la page suivante. 5 Log Assembly (NG , LP) Exploded Parts Diagram (GN, PL) Vue éclatée des pièces Service Parts RCOR-HVB-IPI Beginning Manufacturing Date: 6-03 Ending Manufacturing Date: ______ 1 3 2 4 7 8 6 9 10 ! 12 11 ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 11

    11 (NG , LP) Exploded Part s Diagram / V ue éclatée des pièces IMPORT ANT : THIS IS DA TED INFORMA TION. The most current information is located on your dealers VIP site. When ordering, supply serial and model numbers to ensure correct service part s. / IMPORT ANT : L'information fournie dans cette brochure n'est valide que pendant une ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 12

    12 (NG , LP) Exploded Parts Diagram (GN, PL) Vue éclatée des pièces Service Parts L&RCOR-HVB-IPI Beginning Manufacturing Date: 6-03 Ending Manufacturing Date: ______ IT E M DESCRI PTI O N SERI A L # P A RT NUMB ER 1 Flex Ball Val v e Assem bly / Fl éch i r l 'Assem blée de Sou pap e de Ball e 302-320A 2 O N / O FF W i r e As se m b l ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 13

    13 Appliance Certification The Heat & Glo fireplace models discussed in this Installers Guide have been tested to certification standards and listed by the applicable laboratories. Certification MODELS: PIER-HV B-IPI, S T - H V B-IPI, LCOR-HV B-IPI, RCOR-HV B-IPI LABORA TOR Y : Underwriters Laboratories TYPE: V ented Gas Fireplace Heater ST AND ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 14

    14 2 Getting St arted Introducing the Heat & Glo Gas Fireplaces Heat & Glo direct vent gas fireplaces are designed to oper- ate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. The information contained in this Installers Guide , unless noted otherwise, applies to all models and ga ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 15

    15 Figure 1. Diagram of the PIER-HVB-IPI 42-5/8 (1082mm) Ø 8 (204mm) 12 (305mm) ELECTRICAL ACCE SS GA S LI NE ACCE SS 34-3/4 (882m m ) 4-1/16 (102m m ) 4-1/2 (1 14mm) 4-3/4 (121mm) 2-5/16 (58mm) 37-7/16 (950mm) 32-5/16 (820mm) 21 (533mm) 42 (1067m m ) 17-15/16 (455mm) 24 (610mm) 21 (533mm) 5-1/4 (133mm) 1/2 (1 3mm ) (2) 12 (306mm) Ø 8 (204mm) 8- ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 16

    16 Figure 2. Diagram of the ST -HVB-IPI 5-14 (133 mm) 12 (306m m) 1/2 (13mm) (4) 46-5/ 8 (1183mm) 42 (1067 mm) 32-5/16 (820 mm) 21 (533m m) 36-3/ 16 (919 mm) 2-5/ 16 (58mm) 4-3/ 4 (121 mm) 4-1/1 6 (102 mm) 4-1/ 2 (114mm) ELECT RIC AL ACCESS GA S LIN E ACCESS 12 (305m m) 4-1/2 (114mm) 2-9/ 16 (64mm) 24 (610 mm) 8-1/ 2 (216 mm) 34-3/ 4 (882m m) Ø8 ( ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 17

    17 Figure 3. Diagram of the LCOR-HVB-IPI and RCOR-HVB-IPI 12 (305mm) Ø 8 (204 mm) 34-3/4 (882mm) 4-3/4 (121 mm) 37-7 /16 (950 mm) ELECTR ICAL ACCES S GAS L IN E ACCE SS 42-5/ 8 (10 82mm 2-5/ 16 (58mm) 21 (533mm) 24-1/ 8 (612 mm) 8-1/ 2 (216mm) 21 (533 mm) 42 (1066 mm 32-5/ 16 (820 m) 17- 15/16 (455 mm) 2-9/ 16 (64 mm) 1/2 (13 mm) (4) 5-1/4 (133 mm ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 18

    18 3 Inst alling the Fireplace Step 1. Locating the Fireplace The diagram below shows space and clearance require- ments for locating a fireplace within a room. Minimum Clearances from the Fireplace to Combustible Materials Inches mm Glass Sides or Ends .......... 3 6 .................... 9 1 4 Floor ................................... 0 .......... ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 19

    19 Framing should be constructed of 2 X 4 lumber or heavier . Model A B C D E PIER-HVB-IPI 42-1/8 42-1/2 23 35-3/4 48 ST -HVB-IPI 47-5/8 42-1/2 23 35-3/4 48 L&RCOR-HVB-IPI 42-1/8 42-1/2 28-3/4 35-3/4 48 Figure 5. Framing Dimensions NOTE: DIMENSIONS SHOWN IN INCHES Shows center of 10” x 12” vent framing holes for top and rear venting. The ce ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 20

    20 NOTE: PIPES OVERLAP 1-1/4 INCHES A T EACH JOINT . Figure 6. DVP-Series Direct V ent Component Specifications (5-inch inner pipe / 8-inch outer pipe) D V P 9 0 S T 12- 9/1 6 11 - 1 / 4 7-1 /4 1-1/4 T YP 1/2 TYP 8-9 /16 DVP36 DVP48 48 24 36 4 6 DVP4 DVP6 12 DVP12 2 MIN. DVP12A 12- 3/1 6 MAX . DVP24 9-7 /8 45.0 O 10- 1/4 DVP45 14- 1/4 ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 21

    21 Figure 7. V ent System Component s and T ermination Kit s Step 3. Inst alling the V ent System A. V ent System Approvals These models are approved to use DVP series direct vent pipe components and terminations (see Figures 6 and 7). Approved vent system components are labeled for identifi- cation. This pipe is tested and listed as an approved co ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 22

    22 Figure 8 NOTE: On vertical venting configurations you may want to install the flue re- strictor (385-128). See flue restrictor installation in- structions. Flue Restrictor Instructions 1. Locate the Flue Restrictor which is in the manual bag. Figure 10. Flue Restrictor BRE AK HERE Figure 9 2. Break the Flue R estrictor into two pieces. Do this b ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 23

    23 Figure 14. V enting with One 90° Elbow Figure 13. V enting with One 90° Elbow V H H V NA TURAL GAS - VENTING WITH ONE 90° ELBOW V (FT .) H (FT .) 1' MIN. (305mm) 3' MAX. (914mm) 2' MIN. (610mm) 6' MAX. (1.83m) 3' MIN. (914mm) 9' MAX. (2.7m) 4' MIN. (1.22m) 12' MAX. (3.6m) 5’ MIN. (1.5m) 15’ MAX. (4. ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 24

    24 Figure 15. V enting with T wo 90° Elbows H 1 H V V V 1 H NA TURAL GAS VENTING WITH TWO 90° ELBOWS V (FT .) H + H 1 (FT .) 90 0 Elbow on top 2.5’ MAX. (64mm) 1' MIN. (305mm) 3' MAX. (914mm) 2' MIN. (610mm) 6' MAX. (1.83m) 3' MIN. (914mm) 9' MAX. (2.7m) 4' MIN. (1.22m) 12' MAX. (3.6m) 5’ MIN. (1.5m) 15 ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 25

    25 Figure 16. V enting with T wo 90° Elbows Figure 17. V enting with T wo 90° Elbows H 1 V H V H H 1 NA TURAL GAS VENTING WITH TWO 90° ELBOWS V (FT .) H + H 1 (FT .) 1' MIN. (305mm) 3' MAX. (914mm) 2' MIN. (610mm) 6' MAX. (1.83m) 3' MIN. (914mm) 9' MAX. (2.7m) 4' MIN. (1.22m) 12' MAX. (3.6m) 5’ MIN. (1.5 ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 26

    26 Figure 18. V enting with three 90° elbows H H 1 H 2 V H V H 1 V 1 NA TURAL GAS VENTING WITH THREE 90° ELBOWS V + V 1 (FT .) H + H 1 + H 2 (FT .) 1' MIN. (305mm) 3' MAX. (914mm) 2' MIN. (610mm) 6' MAX. (1.83m) 3' MIN. (914mm) 9' MAX. (2.7m) 4' MIN. (1.22m) 12' MAX. (3.6m) 5’ MIN. (1.5m) 15’ MAX. (4.5m ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 27

    27 Figure 19. V enting with three 90° elbows V H H 1 V 1 V H H 1 V 1 NA TURAL GAS VENTING WITH THREE 90° ELBOWS V + V 1 (FT .) H + H 1 (FT .) 90 0 Elbow on top 2.5’ MAX. (64mm) 1' MIN. (305mm) 3' MAX. (914mm) 2' MIN. (610mm) 6' MAX. (1.83m) 3' MIN. (914mm) 9' MAX. (2.7m) 4' MIN. (1.22m) 12' MAX. (3.6m) 5? ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 28

    28 1. Att ach the First V ent Component to the Starting Collars T o attach the first vent component to the starting collars of the fireplace: • Slide the first vent section onto the unit and push in until they snap lock in position. • Rotate this section to the desired position. • Using the two tabs provided on the elbow cover plate, secure t ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 29

    29 4. Install Firestops For Horizontal Runs - Firestops are REQUIRED on both sides of a combustible wall through which the vent passes. NOTE: Model DVP-TRAP does not need an exterior firestop on an exterior combustible wall. The firestop is built into the cap. T o inst all firestops for horizontal runs that p ass through either interior or exterior ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 30

    30 Figure 26. Ceiling Firestop (Ceiling Side) If the area above the ceiling is NOT an attic, position and secure the ceiling firestop on the ceiling side of the previously cut and framed hole. If the area above the ceiling IS an attic, position and secure the firestop on top of the previously framed hole. NOTE: Keep insulation away from the vent pi ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 31

    31 V = VENT TERMINAL X = AIR SUPPL Y INLET = AREA WHERE TERMINAL IS NOT PERMITTED Figure 29. V ent T ermination Minimum Clearances A = 12" ....................... clearances above grade, veran- da, porch, deck or balcony B = 12" ....................... clearances to window or door that may be opened, or to per- manently closed window . D ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 32

    32 For V ertical T erminations - T o locate the vent and install the vent sections: • Locate and mark the vent centerpoint on the underside of the roof, and drive a nail through the centerpoint. • Make the outline of the roof hole around the centerpoint nail. • The size of the roof hole framing dimensions depend on the pitch of the roof. Ther ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 33

    33 Step 4. Positioning, Leveling, and Securing the Fireplace • Place the fireplace into position. • Level the fireplace from side to side and from front to back. • Shim the fireplace with non-combustible material, such as sheet metal, as necessary . • Secure the fireplace to the framing by nailing or screwing. • Holes are provided in the ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 34

    34 • Insert insulation from the outside of the fireplace and pack the insulation tightly to totally seal between the pipe and the outer casing. • At the gas line access hole the gap between the supply piping and gas access hole can be plugged with non- combustible insulation to prevent cold air infiltration. Step 6. The Gas Supply Line NOTE: Ha ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 35

    35 Step 8. Wiring the Fireplace NOTE: Electrical wiring must be installed by a licensed electrician. CAUTION: DISCONNECT REMOTE CONTROLS IF AB- SENT FOR EXTENDED TIME PERIODS. THIS WILL PRE- VENT ACCIDENT AL FIREPLACE OPERA TION. For Intermittent Pilot Ignition Wiring Appliance Requirements This appliance requires that 1 10-120 V AC be wired to the ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 36

    36 Wall Switch Position the wall switch in the desired position on a wall. Run a maximum of 25 feet (7.8 m) or less length of 18 A.W .G . minimum wire and connect it to the fireplace ON/OFF switch pigtails. CAUTION: LABEL ALL WIRES PRIOR TO DISCONNEC- TION WHEN SERVICING CONTROLS. WIRING ERRORS CAN CAUSE IMPROPER AND DANGEROUS OPERA TION. VERIFY PR ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 37

    37 Step 9. Finishing Figures 38 and 39 show the minimum vertical and corresponding maximum horizontal dimensions of fireplace mantels or other combustible projections above the top front edge of the fireplace. See Figures 4 and 5 for other fireplace clearances. Only non-combustible materials may be used to cover the black fireplace front. W ARNING: ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 38

    38 Inst alling the T rim Combustible materials may be brought up to the specified clearances on the side and top front edges of the fireplace, but MUST NEVER overlap onto the front face. The joints between the finished wall and the fireplace top and sides can only be sealed with a 300° F . (149° C) minimum sealant. W ARNING: WHEN FINISHING THE FI ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 39

    39 Placing the Ember Material Ember material is shipped with this gas fireplace. The bag labeled Glowing Ember (050-721) is standard glowing em- ber material. T o place the ember material: • Remove the wing nuts and glass clips or tension springs around the glass door . • Remove the glass door from the unit. • Remove the grate and log set by ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 40

    40 Step 1 1. Before Lighting the Fireplace Before lighting the fireplace, be sure to do the following: ! ! Step 12. Lighting the Fireplace Y ou’ve reviewed all safety warnings, you’ve checked the fireplace for gas leaks, you know the vent system is unobstructed, and you’ve checked for faulty components. Now you’re ready to light the firepla ...

  • Hearth and Home Technologies RCOR-HVB-IPI - page 41

    41 4 Maint aining and Servicing Y our Fireplace Fireplace Maintenance Although the frequency of your fireplace servicing and main- tenance will depend on use and the type of installation, you should have a qualified service technician perform an appli- ance check-up at the beginning of each heating season. See the table below for specific guideline ...

Fabricant Hearth and Home Technologies Catégorie Indoor Fireplace

Les documents que nous recevons du fabricant de l'appareilHearth and Home Technologies RCOR-HVB-IPI peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Hearth and Home Technologies
- manuels d’utilisations RCOR-HVB-IPI
- fiches produit Hearth and Home Technologies
- dépliants
- ou étiquettes-énergie Hearth and Home Technologies RCOR-HVB-IPI
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Hearth and Home Technologies RCOR-HVB-IPI.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Hearth and Home Technologies RCOR-HVB-IPI, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Hearth and Home Technologies RCOR-HVB-IPI. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Hearth and Home Technologies RCOR-HVB-IPI.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Hearth and Home Technologies RCOR-HVB-IPI, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Hearth and Home Technologies RCOR-HVB-IPI par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Hearth and Home Technologies RCOR-HVB-IPI.

Le manuel d’utilisation complet Hearth and Home Technologies, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Hearth and Home Technologies RCOR-HVB-IPI - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Hearth and Home Technologies RCOR-HVB-IPI, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lHearth and Home Technologies RCOR-HVB-IPI qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Hearth and Home Technologies RCOR-HVB-IPI - qui devraient nous aider dans les premières étapes lors de l'utilisation Hearth and Home Technologies RCOR-HVB-IPI
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Hearth and Home Technologies RCOR-HVB-IPI
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Hearth and Home Technologies RCOR-HVB-IPI dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Hearth and Home Technologies RCOR-HVB-IPI?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Hearth and Home Technologies RCOR-HVB-IPI, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Hearth and Home Technologies RCOR-HVB-IPI il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)