Français dropdown-ico

Manuel d’utilisation Robin America EH12-2, EH17-2, EH25-2

78 pages 3.08 mb
Télécharger

Aller à la page of 78

Summary
  • Robin America EH12-2, EH17-2, EH25-2 - page 1

    ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 2

    CONTENTS Section Title 1 . 2 . 3 . 4 . 5 . 6 . 7 . 8 . Page 4-1 4-2 4-3 4-4 4-5 4-6 4-7 4-8 4-9 4-1 0 4-1 1 4-1 2 4-1 3 4-1 4 4-1 5 4-1 6 4-1 7 ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 3

    ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 4

    I. SPECIFICATIONS ~~ ~ ~~~ ~ ~ ~~ ~~ ~~~ ~~~~ ~~ ~~~ ~ ~ EH 12-2 EH12-2B EH12-2DS EHl2-2D EH12-2BS Model TY Pe Air-Cooled, 4-Cycle, Single-Cylinder, Horizontal P.T.O. Shaft, Gasoline Engine Bore X Stroke Piston Displacement 60 x 43 rnm (2.36 x 1.57 in.) 121 cm3 (7.38 cu.in.) I Max. Torque Nem (kaf*m)/rDm 15 (1 52) /1300 7.5 (0.76) /2600 Direction o ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 5

    EH17-2 EH17-2B EH17-2DS EH17-2D EH17-2BS Model TY Pe Air-Cooled, 4-Cycle, Single-Cylinder, Horizontal P.T.O. Shaft, Gasoline Engine Bore X Stroke ~~ ~~ ~~ ~~~~ ~ ~ 67 x 49 mrn (2.64 X 1.93 in.) 172 cm3 (10.50 cu.in.) . Compression Ratio 8.5 Output 2.6 (3.5) /3000 2.9 (4.0) /3600 2.6 (3.5) / 1500 2.9 (4.0) / 1800 Continuous Kw (HP)/rpm 4.4 (6.0) /40 ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 6

    ~~~~~~ ~~ ~ EH25-2 EH25-2 6 EH25-2DS EH25-2D EH25-26s Model TY Pe Air-Cooled, 4-Cycle, Single-Cylinder, Horizontal P.T.O. Shaft, Gasoline Engine Bore x Stroke Piston Displacement 75 X 57 mm (2.95 X 2.24 in.) 251 cm3 (15.31 cu.in;) Compression Ratio 8.5 output 4.0 (5.5) /3000 4.7 (6.4) /3600 4.0 (5.5) I1 500 4.7 (6.4) / 1800 Continuous Kw (HP)hm 6.3 ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 7

    2-1 MAXIMUM OUTPUT The maximum output is the output of an engine with its throttle valve fully opened under the condition that all the moving parts are properly worn in after the initial break-in period. A new engine may not produce full maximum output while its moving parts are still not broken-in. 2-2 CONTINUOUS RATED OUTPUT The continuous rated ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 8

    2-4 PERFORMANCE CURVES 8 0 EHlPD, B HP kW 4 3 + 3 l2 n + 0 3 1 0 2 1 for B type 2000 3000 (1 000) (1 500) REVOLUTION - r.p.m. 4000 (2000) -5- ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 9

    0 EH17D, 6 for B tvDe (1 000) REVOLUTION - r.p.m. N.m kgfam 3000 4000 (1 500) (2000) -6- ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 10

    EH25D, B HP 8 7 t: $4 & I- 2 1 0 r I I I I I I I I I I " "- I I 1 " MAXIMUM TORQUE AL I I I I I kW I I MAXIMUM HORSEPOWER '(NET) I -6 5 4 I RECOMMENDED I i N.m kgf-m 16.5 (33) 15.5 (31) 14.5 (29) 1.7 (3.4) 1.6 (3.2) 1.5 (3.0) 1.4 (2.8) c 2000 3000 ' 4000 (1 000) (1 500) (2000) REVOLUTION - r.p.m. -7- ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 11

    3. FEATURES , , 1. The overhead valve design offers a compactness, light weight and ideal combustion characteristics 2. An optimum lubrication and better tilted operation thanks to upright cylinder design. 3. A crossflow arrangement of intake and exhaust ports ensures stable performance under high ambient temperature. 4. The automatic decompressiom ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 12

    4-3 CRANKSHAFT The crankshaft is forged carbon steel, and the crank The output end of the shaft has a crankshaft gear, and balancer gear for EH25-2 which are pressed into position. W pin is induction-hardened. 44 CONNECTING ROD AND PISTON The connecting rod is an aluminum alloy diecasting, and its large and smalI ends function as bearings. The pist ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 13

    4-6 CAMSHAFT The camshaft for the D-type engine is made of special cast iron and camshaft gears are casted to- gether in one piece. Both sides of the shaft fit into the plane bearings on the crankcase and main bearing cover. The camshaft for the B-type engine is made of forged carbon steel and also functions as PTO shaft. The cam gear is press fitt ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 14

    4-9 GOVERNOR SYSTEM The governor is a centrifugal flyweight type which ensures constant operation at the selected speed against load variations. The governor gear with governor weights is installed on the main bearing cover. 4-10 COOLING SYSTEM The large fins on the flywheel provide sufficient cooling air capacity for the inlet and exhaust area and ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 15

    4-13 CARBURETOR The engines are equipped with a horizontal draft carburetor that has a float controlled fuel system and a fixed main jet. The carburetors are calibrated carefully for easy starting, good acceleration, low fuel consumption and sufficient output. 4-14 AIR CLEANER The air cleaner is a single urethane foam element system. As an option, ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 16

    4-16 DECOMPRESSION SYSTEM An automatic decompression mechanism which opens exhaust valve before the piston reaches com- pression top is assembled on the camshaft for easy starting. AUTOMATIC DECOMPRESSOR SYSTEM Fig. 4-14 - 13- ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 17

    4-1 7 SECTIONAL VIEW OF ENGINE FUEL TANK FLYWHEEL MAIN BEARING COVER - 14- ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 18

    a ROCKER ARM PUSH ROD - 15 - ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 19

    5. DISASSEMBLY AND REASSEMBLY 5-1 PREPARATIONS AND SUGGESTIONS 1) When disassembling the engine, memorize the locations of individual parts so that they can be reassembed correctly. If yor are uncertain of identifying some parts, it is suggested that tags be attached to them. 2) Have boxes ready to keep disassembed parts by group. 3) To prevent los ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 20

    5-3 DISASSEMBLY PROCEDURES Step Tool Remarks Procedures Part to remove I 1 14mm box wrench Be careful not to lose the (1) Remove oil drain plug and drain oil. Oil drain (2) To discharge oil quickly, remove oil gasket. gauge. GASKET I Fig. 5-2 DRAIN PLUG - 17 - ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 21

    Step Tool Remarks Procedures Part to remove I 2 Fuel tank 1 (1) Close fuel valve. (2) Disconnect fuel hose between fuel strainer and carburetor. (3) Remove fuel tank from cylinder head. M6X14mm bolt *.-- 4pcs. (EH12-2,17-2) M8X20mm bolt 0- 4pcs. (EH25-2) ~ ~ ~~ ~~ Wipe off spilt fuel thoroughly. 1 Omm (1 2mm) socket wrench (EH12-2, 17-2) (EH25-2) F ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 22

    Step I Part to remove I Procedures I Remarks I Tool Recoil starter (1) Remove recoil from blower housing. M6 X 8mm flange bolt - - 4pcs. 1 Omm box wrench I housing 5 Oil sensor (Option) I (1) Remove blower housing from crankcase. M6X i2mm flange bolt 4pcs. lOmm box wrench (1) Remove oil sensor probe. Be careful not to damage stick and sensor since ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 23

    )art to remove Muffler cover, Muffler and Exhaust pipe cover Procedures (1) Remove muffler cover and exhaust pipe cover. M6X lOmm flange bolt 0.. Spcs. (2) Remove muffler from crankcase and cylinder head. M8 nut 2pcs. M6 X 12mm flange bolt - 1 PC. M8X 16mm flange bolt - 1 pc. (EH25-2) (EHl2-2,17-2) I Remarks Be careful not to lose muffler gasket. T ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 24

    Control box and Electric (Option) Procedures Tool Remarks (1) Disconnect wires. blue 1 (diode rectifier ) light blue 1 (diode rectifier ) black *** 1 (magnetic switch) (2) Remove black wires from electric starter. (3) Remove control box. 12mm socket wrench (4) Loosen two bolts and remove electric Fastened together with fuel tank. starter. M8 bolt 2 ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 25

    Head cover L Air cleaner Procedures Tool Remarks (1) Remove head cover from crankcase. 1 Omm M6 X 12mm flange bolt 1 pc. socket wrench (1) Remove cleaner cover and cleaner lOmm Fastened together with element. M6 flange nut 2pcs. socket wrench carburetor. 1 (2) Remove cleaner case. c .GASKET CLEANER CASE c c Fig. 57 - 22 - ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 26

    Step 10 - 11 12 - 13 - Part to remove I ~ Procedures Governor lever, Governor rod and Governor spring Carburetor (1) Unhook governor spring from speed control lever. (2) Remove governor lever from governor shaft. M6X30mm bolt and washer -e lpc. (3) Detach governor lever, governor rod and rod spring from carburetor. (1) Remove carburetor from intake ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 27

    14 Ignition coil l- “ ” Procedures I Remarks (1) Disconnect ignition plug cap and remove ignition coil from crankcase. M6X25mm bolt and washer ...- 2pcs. (1) Remove starter pulley from flywheel. Place socket wrench on flywheel fastening nut and strike tip of the lever with hammer. Refer to the illustration below. (See Fig. 5-9.) 14mm nut lpc. ( ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 28

    Step Too I Remarks Procedures Part to remove 16 Flywheel puller Use flywheel puller as (1) Remove flywheel from crankshaft. Flywheel (2) Remove key from crankshaft. illustrated below. (See Fig. 5-12.) (See Fig. 5-1 1.) ~ 17 (1) Remove charge coil. Charge coil I (Option) M6 X 25mm Screw 2pcs. 18 21 mrn (1) Remove spark plug from cylinder head. Spark ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 29

    step 19 20 ~~~ ~ Part to remove Rocker cover Cylinder head Procedures Remarks (I) Remove rocker cover from cyIinder head. (2) Remove gasket. (rocker cover) M6X 12mm flange bolt ..-. 4pcs. (1) Remove cylinder head from crankcase. M8x65mm flange bolt .... 4pcs. MIOX75mmflangebolt --.- 4pcs. (EH12-2, 17-2) (EH25-2) (2) Detach cylinder head gasket from ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 30

    Step 21 - Part to remove Main bearing cover Procedures (1) Remove main bearing cover fastening bolts. M6X30mm bolt and washer - 8pcs. M8X30mm bolt and washer -.-. 8pcs. (2) Remove main bearing cover using plastic (EH 12-2, 17-2) (EH25-2) hammer. (See Fig. 5-15) I ! I - - L Fig. 5-15 Remarks Be careful not to damage oil seal. MAIN M6 BOLT and WASHER ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 31

    I I Step 22 - - 23 Part to remove , Procedures 1 Cam shaft and Balancer shaft (Option for EH25-2) Tappet (1) Remove cam shaft from crankcase. (2) Remove balancer shaft. (Option for EH25-2) (1) Remove tappets from crankcase. Remarks Tool t To prevent tappets from getting damaged, put the crankcase upside down. (See Fig. 5-17.) Put a tag on tappets t ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 32

    Step I Partto remove I Procedures 24 ~~~ Connecting (1) Remove connecting rod bolt after scraping rod and off carbon from cylinder and piston. Piston M6 X 34mm flange bolt 2pcs. (EHI 2-2) M7X37mm flange bolt 2pcs. (EH17-2) M8x46mm flange bolt 2pcs. (EH25-2) (2) Remove connecting rod cap. (3) Remove connecting rod from upper side of crankcase after ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 33

    Step Too! Remarks Procedures Part to remove 26 Be careful not to damage (1) Remove crankshaft tapping at the Crankshaft flywheel end. oil seal. c Fig. 5-20 c CRANKSHAIT (D type) c fig. 5-21 - 30 - ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 34

    Step 27 'art to remove Intake valve and Exhaust valve Procedures (1) Loosen nut and remove bolt (pivot). (2) Remove rocker arms. (3) Press down spring retainer, take out collet valve, and then remove spring retainer and valve spring (4) Remove intake and exhaust valve. .(See Fig. 5-23.) Remarks Inspect valves, valve seats and guide. Do not rem ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 35

    5-4 REASSEMBLY PROCEDURES 0 PRECAUTIONS FOR REASSEMBLY 1) Clean parts throughly before reassembly. Pay most attention to cleanliness of piston, cylinde :r, crankshaft, connectin g rod and bearings. Scrape off all carbon deposits from cylinder head, piston top and piston ring grooves. Check lip of oil seals. Replace oil seal if the lip is damaged. A ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 36

    Fig. 5-28 5-4-3 PISTON AND CONNECTING, ROD (1) When installing the piston on the connecting rod, place the valve rcess of the piston crown as shown in the illustration to the "MAG" side of the connecting rod. Apply oil to the small end of the connecting rod, piston and piston pin before installation. Be sure to use clips on the both end o ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 37

    (2) Install the piston and connecting rod assembly into the cylinder. Use a piston ring compressor to hold the piston rings. Place “MAG” side of the connecting rod on the magneto side of the crankcase. [NOTES] (1) Apply enough oil to piston rings, connecting rod bearings and cylinder bore before assembly. (2) Set gaps of the piston rings 90 deg ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 38

    5-4-5 BALANCER SHAFT (Option for EH25) Install balancer shaft aligning the timing mark on the balancer shaft gear and the balancer gear on the crank shaft as shown in the illustration. Incorrect timing of the gears will cause matfunction of the engine and may result in damage due to interference of the parts. 5-4-6 TAPPET AND CAMSHAFT (1) Oil the t ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 39

    5-4-7-1 CRANKSHAFT END PLAY (For D type and B type) (1) Measure the depth “Al” (From the mating surface to the inner race of the ball bearing.) (2) Measure the height “Bl” (From the mating surface to the crank gear.) (Al+ 0.3) - Bl=SIDE CLEARANCE (mm) (SIDE CLEARANCE) - 0.2=THICKNESS OF CRANKSHAFT SHIM (mm) (A+ 0.012”) - Bl=SIDE CLEARANCE ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 40

    MAIN Fig. 5-36 (2) Lubricate the oil seal and bearing surfaces. Add a light film of oil on the main bearing cover face to hold the gasket in place. Place spacers chosen at procedure (1) on crankshaft and camshaft. Use an oil seal guide when installing the main bearing cover to avoid damaging the seal. Tap the cover into place with a soft hammer. Ma ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 41

    5-4-8 CYLINDER HEAD (1) Clean carbon and gum deposits from the valves, seats, ports and guides. Inspect the valves, valve (2) Replace valves that are badly burned, pitted or warped. (3) When installing the valves in the cylinder head, oil the valve stems and insert them into the valve guide. Then place the cylinder head on a flat table, install the ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 42

    (2) Loosen the nut under the rocker arm and turn the bolt (pivot) to adjust the clearance between the rocker arm and the valve stem end. Tighten the nut under the rocker arm. I Valve clearance I I 0.08-0.1 2 mm 0.0031 -0.0047 in. I Check operation of valves by turning crankshaft. Recheck valve clearance. (3) Install rocker cover and gasket. Rocker ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 43

    1 Tightening torque I I 59-63 N-m I 600-650 kgocm I 43-47 ft*lb I 54-13 IGNITION COIL Install the ignition coil to the crankcase. Adjust the air gap between the ignition coil and the flywheel using a thickness gauge (filler gauge) and tighten the bolts. Tightening torque 8.8-10.8 Nom I 90-1 10 kgecrn 6.5-8.0 ft4b A Fig. 5-40 5-4-14 INTAKE PIPE, lNS ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 44

    (3) Connect the speed control lever and the governor lever with the governor spring. The governor spring ’ (4) Turn the speed control lever all the way toward the high speed position and make sure that the throttle (5) Turn the governor shaft clockwise all the way using a screw driver, and tighten the lock bolt and nut. should be hooked to the nu ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 45

    54-17 AIR CLEANER Install the air cleaner gasket and the cleaner case and tighten them with 2-M6 flange nuts. Then install the element and the cleaner cover. 5-4-1 8 HEAD COVER Install the head cover to the cylinder head. M6 X 12mm flange bolt ..a- 1 PC. 54-19 MUFFLER, MUFFLER COVER and EXHAUST PIPE COVER Install the muffler to the cylinder head. M ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 46

    5-5 BREAK-IN OPERATION B An engine that has been completely overhauled by being fitted with a new piston, rings, valves and connecting rod should be throughly RUN- IN before being put back into service. Good bearing surfaces and running clearances between the various parts can only be established by operating the engine under reduced speed and load ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 47

    2) At the higher engine speed Rotation of the flywheel generates the current I1 as this current flows through the base terminal of the power transistor, it is activated and the current IZ starts of flow. As the engine reaches the ignition timing, the ignition timing control circuit for the higher engine speed is activated and provides the base curr ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 48

    6-3 WIRING DIAGRAM STANDARD Stop switch Connector Black Black > Spark Plug Ignition Coil Flywheel ElNGlNE WITH ELECTRIC STARTER DIODE RECTIFIER I """"_"""" I L 12VOLT BATTERY MtNIMUM 24 AMP.HR. Fig. 6-3 - 45 - ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 49

    7. AUTOMATIC DECOMPRESSION SYSTEM EH12-2, 17-2, 25-2 engines are employing the automatic decompression system as a standard feature. This enables easy and light start of the engine. The automatic decompression system releases the compression of the engine by lifting up the exhaust valve at the cranking. Following are the explanation using type “D ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 50

    8. CARBURETOR B 8-1 OPERATION AND CONSTRUCTION 8-1 -1 FLOAT SYSTEM The float chamber is located below the carburetor body and, with a float and a needle valve, maintains a constant fuel level during the engine operation. The fuel flows from the fuel tank into the float chamber through the needle valve. When the fuel rises to a specific level, the f ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 51

    8-1-2 PILOT SYSTEM The pilot system feeds the fuel to the engine during idling and low-speed operation. /"l The .fuel is fed through the main jet to the pilot jet, where it is metered, and mixed with the air metered by the pilot air jet. The fuel-air mixture is fed to the engine through the pilot outlet and the by-pass. At the idling speed, th ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 52

    8-2-4 MAIN SYSTEM (1) Remove the bolt(l2)and take out float chamber body(l3). B (2) From the body (14) remove the main nozzle (15), and then remove the main jet (16) and guide holder (17) from the main nozzle (15). (3) Reassembly a)Fasten the main jet securely to the body. Otherwise, the fuel may become too rich and cause engine b)The bolt tighteni ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 53

    9. STARTING SYSTEM 9-1 RECOIL STARTER Equipments to be prepared : Driver, Pinchers (Pliers) and Protective Glasses WARNING starting the disassembly; make sure to wear the protective glasses. 9-1-1 Disassembly Steps I / (1) Setting off the spring power -1 : Hold the starter knob and extract the starter 1 rope. -2 : Extract the rope fully and hold th ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 54

    WARNING Before starting the assembly, make sure to wear the protective glasses. 9-1-2 Assembly Steps GREASE PASTING (1) Setting the reel into the case. -1 :Paste grease on the case. (Fig. 9-3) -2 : Adjust the position of the inner end of the spring, which is set in the reel. (Fig. 9-4) -3 :Hold the reel so that the shafthook part and the inner end ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 55

    -1 i Push the latchet-guide lightly by hand so that the latchet guide won’t move and tighten the set-screw. (4) Storing the spring-power. -1 :Hold the case tight and using both hands, wind up the reel counter-clockwise 6 times. -2: Set the ree to keep the position, whereby the rope hole of the reel and the rope guide make a direct line. (Fig. 9-7 ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 56

    (6) Test the operation of the recoil starter to see if the rope recoils satisfactorily and the ratchets project and retract properly. Mount the recoil starter to the engine. (7) If the spring escapes from the reel when disassembling the recoil, hook the outer end of the spring onto the notch of the reel and rewind the spring into the housing. (8) L ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 57

    IO. TROUBLESHOOTING The following three conditionts must be fulfilled for satisfactory engine start. 1. The cylinder filled with a proper fuel-air mixture. 2. Good compression in the cylinder. 3. Good spark, properly timed, to ignite the mixture. The engine cannot be started unless these three conditions are met. There are also other factors which ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 58

    10-1-3 IGNITION SYSTEM Check the followings for lack of sparks. (1) Wires of the ignition coil, spark plug or contact breaker disconnected. B (2) Ignition coil damaged and shorted. (3) Spark plug cable wet or soaked with oil. (4) Spark plug dirty or wet. (5) Spark plug electrode gap incorrect. (6) Spark plug electrodes are connected or bridged. (7) ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 59

    10-5 ENGINE KNOCKS (1) Poor quality gasoline. (2) Engine operating under heavy load at low speed. (3) Carbon or lead deposits in the cylinder head. (4) Spark timing incorrect. (5) Loose connecting rod bearing due to wear. (6) Loose piston pin due to wear. (7) Cuases of engine overheat. 10-6 ENGINE BACKFIRES THROUGH CARBURETOR (1) Water or dirt in g ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 60

    11. INSTALLATION Engine life, ease of maintenance and inspection, frequency of checks and repairs, and operating cost all I) depend on the way in which the engine is installed. Review the following instructions carefully for installing the engine. 11-1 INSTALLING When mounting the engine, carefully examine its position, the method of connecting it ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 61

    12. SERVICE DATA “STD” in the following table is the parts dimension from the brand new engine or the spare parts. Whereas, “Limit” shows the maximum allowance for the parts to be used on the engine. If the measurement exceeds beyond the “Limit”, the part needs to be replaced and/or repaired. 12- 1 CLEARANCE DATA AND LIMITS r Flatness 1 ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 62

    Unit: mm (in) EH 1 2-2 EH 1 7-2 I ITEM Lmit STD STD Lm it To be rebored when the lifference letween ma. snd min. of jiameter .cached to 0.1 :0.004). -0 be rebored vhen the lifference letween ma. nd rnin. of jiameter eached to 0.1 0.004). CYLINDER Inside dia. 57.000 - 67.01 9 2.6378 - 2.6385) 60.000 - 60.01 9 (2.3622 - 2.3630) STD 60.250 - 60.269 (2 ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 63

    Unit: mm (in) ITEM 2Y LIN DER inside dia. B Roundiness after reboring. Cyiindricity after reboring. PI STON 0 Piston size (At skirt in thrust direction) STD 1 st reboring 2nd reboring STD 1 st 01s 2nd OJS r EH25-2 STD 75.000 - 75.01 9 2.9528 - 2.9535) 75.250 - 75.269 2.9626 - 2.9633) 75.500 - 75.51 9 2.9724 - 2.9732) LESS THAN 0.01 (0.004) LESS THA ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 64

    Uni : rnm (in) T EH17-2 ITEM STD Limit STD Limit 0 Ring groove side clearance 0.030 - 0.075 (0.001 2 - 0.0030) 0.1 5 (0.006) 0.15 (0.006) 0.035 - 0.080 :0.0014 - 0.0031) 0.030 - 0.075 (0.001 2 - 0.0030) 0.1 5 (0.006) 0.025 - 0.070 (0.0010 - 0.0028) 0.1 5 (0.006) t 2nd 0.020 - 0.075 (0.0008 - 0.0030) 0.1 5 (0.006) 0.01 0 - 0.065 (0.0004 - 0.0026) 0. ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 65

    Unit: mrn (in) 1 Ring groove side clearance I Piston pin hole ~rn Piston pin outside dia. Clearance between piston and cylinder at skirt area. I Piston ring end gap 2nd Oil ring TOP 2nd oil ring EH25-2 STD 0.050 - 0.090 1.0020 - 0.0035) ~ ~ ~ ~~~~~ 0.030 - 0.070 ).0012 - 0.0028) 0.010 - 0.065 1.0004 - 0.0026) 17.991 - 18.002 1.7083 - 0.7087) 17.992 ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 66

    Unit: mm (in) ITEM EH 1 2-2 STD Limit ZONNECTING ROD D Big end inside dia. 26.000 - 26.01 3 (1 -0236 - 1.0241) 26.1 (1.0276) Clearance between big end and crankpin 0.020 - 0.046 (0.0008 - 0.001 8) 0.2 (0.008) I 0 Small end inside dia. 13.08 (0.51 50) 13.01 0 - 13.021 (0.51 22 - 0.51 26) 0 Clearance between small end and piston pin 0 Big end side cl ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 67

    m- ITEM - EH 1 7-2 STD CONNECTING ROD 0 Big end inside dia. Clearance between big end and crankpin Small end inside dia. Clearance between big end and crankpin Small end inside dia. 0 Clearance between small end and piston pin Big end side clearance I CRANKSHAFT 0 Journal dia. Unit: mm (in) 30.000 - 30.01 6 (1.1811 -1.1817) 0,020 - 0.049 (0.0008 - ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 68

    lTEM F EH25-2 ~ STD 0 Clearance between big end and crankpin 0 Small end inside dia. t I 0 Clearance between small end and piston pin 0 Big end side clearance I CRANKSHAFT 0 Journal dia. - I 34.000 - 34.01 6 (1.3386 - 1.3392) 0.025 - 0.057 (0.0010 - 0.0022) 18.01 0 - 18.021 (0.7091 - 0.7095) 0.01 0 - 0.029 (0.0004 - 0.001 1) 0.1 - 0.7 (0.004 - 0.02 ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 69

    Unit : mrn (in) EH12-2 / EH17-2 ITEM STD Limit CAMSHAFT 0 Cam height 29.6 - 29.8 (1.165 - 1.173) 29.45 (1.1 59) IN.=. CAMS I Journal outside dia. "D" type 16.973 - 16.984 (0.6682 - 0.6687) 16.95 (0.6673) Dl Dl 14.973 - 14.984 (0.5895 - 0.5899) 14.95 (0.5886) D2 VALVE Valve stem outside dia. 5.440 - 5.455 (0.21 42 - 0.21 48) 5.35 (0.21 06) ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 70

    Unit: mm (in) ZAMSHAFT Cam height a Journal outside dia. 'D" type ITEM IN.=. CAMS Dl VALVE Valve stem outside dia. Clearance between valve stem dia. and valve guide "P 1 .. .. .. .. .. .. .. .. Valve clearance D2 IN. Ex. IN. EX. IN ./EX. (cold) EH25-2 I Limit 30.6 - 30.8 (1.205 - 1.213) 30.45 (1.199) 24.967 - 24.980 (0.9823) (0.9830 ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 71

    ITEM TAPPET 0 Stem outside dia. 0 Guide inside dia. 0 Tappet guide clearance VALVE SPRING FREE LENGTH Unit: rnrn (in) 1 STD 7.960 - 7.975 (0.31 34 - 0.31 40) 8.000 - 8.01 5 (0.31 50 - 0.31 56) 0.025 - 0.055 (0.001 0 - 0.0022) Limit - 68 - ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 72

    Unit: mrn (in) ITEM TAPPET Stem outside dia. Guide inside dia. 8 0 Tappet guide clearance VALVE SPRING FREE LENGTH ~~ ~ ~~~ I ITEM VALVE SEAT ANGLE(IN. EX.) 0 Valve cutter angle(a) 0 Valve contact width(b) a EH25-2 STD Limit 7.960 - 7.975 (0.31 34 - 0.31 40) 8.000 - 8.01 5 (0.31 50 - 0.31 56) 0.025 - 0.055 (0.001 0 - 0.0022) 35.5 (1.4) 1 ~ Unit: rn ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 73

    12-2 TORQUE SPECIFICATIONS EH12-2 / 17-2 type TIGHTENING TORQUE N*m ft- Ib kg cm DESCRIPTION Cylinder head bolts 5.7 - 7.2 80 - 100 7.8 - 9.8 Main bearing cover bolts 43 - 47 600 - 650 58.8 - 63.7 Flywheel nut Connecting rod cap bolts 16.6 - 19.5 230 - 270 22.5 - 26.5 EH12-2 12.2-14.4 6.5-8.3 170-200 90-115 .16.6-19.6 8.8-11.2 EH17-2 EH12-2 EH17-2 ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 74

    12-3 OIL GRADE CHART Specified Lubrican Quality T- Single grade Multi- grade Comparison between oil viscosity and temparature I I I I I 1 I I I - 20 - 10 0 10 20 30 40 "C -4 14 32 50 68 86 104 "F Use oil classified as SE or higher. Multi-grade oil tends to increase its consumption at high ambient temperature. - 71 - ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 75

    13. MAINTENANCE AND STORAGE The following maintenance jobs apply when the engine is operated correctly under normal conditions. The indicated maintenance intervals are by no means guarantees for maintenance free operations during these intervals. For example, if the engine is operated in extremely dusty conditions, the air cleaner should be cleaned ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 76

    13-4 EVERY 100-200 HRS. (MONTHLY) MAINTENANCE I MAINTENANCE I REMARKS I ~ 1) Clean fuel filter and fuel tank. 2) Inspect cooling system and remove dirt and Remove blower housing and clean up between fins and housing. chaff. 13-5 EVERY 500-600 HRS. MAINTENANCE I MAINTENANCE I REMARKS I I 1) Remove carbon from cylinder head. ~ ~~~ I Carbon deposits i ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 77

    ...

  • Robin America EH12-2, EH17-2, EH25-2 - page 78

    SU6ARU ~bin America, Inc. 940 Lively Blvd. l Wood Dale, IL 60191 l Phone: 630-350~8200 l Fax: 630-350-8212 e-mail: sale.s@robinamerica.com l www.robinamerica.com PRINTED IN THE USA I ...

Fabricant Robin America Catégorie Portable Generator

Les documents que nous recevons du fabricant de l'appareilRobin America EH12-2, EH17-2, EH25-2 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Robin America
- manuels d’utilisations EH12-2, EH17-2, EH25-2
- fiches produit Robin America
- dépliants
- ou étiquettes-énergie Robin America EH12-2, EH17-2, EH25-2
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Robin America EH12-2, EH17-2, EH25-2.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Robin America EH12-2, EH17-2, EH25-2, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Robin America EH12-2, EH17-2, EH25-2. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Robin America EH12-2, EH17-2, EH25-2.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Robin America EH12-2, EH17-2, EH25-2, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Robin America EH12-2, EH17-2, EH25-2 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Robin America EH12-2, EH17-2, EH25-2.

Le manuel d’utilisation complet Robin America, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Robin America EH12-2, EH17-2, EH25-2 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Robin America EH12-2, EH17-2, EH25-2, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lRobin America EH12-2, EH17-2, EH25-2 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Robin America EH12-2, EH17-2, EH25-2 - qui devraient nous aider dans les premières étapes lors de l'utilisation Robin America EH12-2, EH17-2, EH25-2
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Robin America EH12-2, EH17-2, EH25-2
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Robin America EH12-2, EH17-2, EH25-2 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Robin America EH12-2, EH17-2, EH25-2?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Robin America EH12-2, EH17-2, EH25-2, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Robin America EH12-2, EH17-2, EH25-2 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)