-
Profile 100SX - page 1
100SX 200SX 400SX 600SX 800SX 1200SX 440SX 640SX MOSFET POWER AMPLIFIERS Installation Instructions / Owner's Man ual ...
-
Profile 100SX - page 2
I NTRODUCTION Congratulations on your purchase of a California state-of-the-art power amplifier. Your selection of a California car audio product indicates a true appreciation of fine musical reproduction. Whether adding to an exi sting system or including your California amplifier in a new system, you are certain to notice immediate performance be ...
-
Profile 100SX - page 3
S AFETY PRECAUTIONS Fuse amplifier’s power wire at the battery . Be sure to fuse the power wire within 12” of the car's battery. This will protect the car's battery in case of a short circuit between the power amplifier and battery. THIS IS A MUST, the amplifier's built-in fuse will only protect the power amplifier not the car&ap ...
-
Profile 100SX - page 4
F EATURES AND BENEFITS DC Offset Protection This circuit protects the output of the amplifier against DC voltage. If for some reason DC voltage is detected at the output stage, the amplifier will shut down protecting the speakers from direct current. Short Circuit Protection The circuit protects the amplifier from damage due to a short found in the ...
-
Profile 100SX - page 5
Bass Boost For added low frequency performance the two channel amplifiers are equipped with 12dB bass boost. Power Fusing This protects the amplifier against short circuits and excessive current. Remote Turn-on Automatically turns amplifier on when connected to the head unit's remote output. The amplifier will turn on and off with the head uni ...
-
Profile 100SX - page 6
M OUNTING LOCATION Before you start the installation, it will be necessary to find a mounting location for the amplifier. Find a location in which the amplifier will receive adequate ventilation in order to dissipate the heat it develops during operation. Two popular mounting locations are in the trunk or under the seat. Select the location in whic ...
-
Profile 100SX - page 7
Connect the amplifier to the car's battery. At times, the amplifier will need to draw large levels of current that cannot be provided by any circuit in the car's fuse box. We recommended using an 8 to 10 gauge power wire for your connections depending on the amplifier and length of the wire. Strip one end of the wire to connect to the ter ...
-
Profile 100SX - page 8
7 INPUT CH1 CH2 CH4 CH3 X-OVER 40Hz 130Hz X-OVER 40Hz 130Hz BASS BOOST 0dB 12dB BASS BOOST 0dB 12dB FILTER LOW HI OFF FILTER LOW HI OFF MIN MIN MAX MAX LEVEL LEVEL 85Hz 85Hz R R Connect 2 sets of RCA “Y” adaptors to split the two RCA’s from the radio into 4 outputs (Not Provided) L L INPUT FILTER X-OVER BASS BOOST LEFT RIGHT MIN MAX 40Hz 130H ...
-
Profile 100SX - page 9
8 If a low level RCA signal source is not available, you may still wire the models 100SX, 200SX, and 400SX with high-level or speaker level outputs from your head unit. However, only speaker leads from a "floating ground" system may be used (see diagram below). Use the strip connector located on the end of the amplifier to make this conne ...
-
Profile 100SX - page 10
B + REM GND FUSE L - R + R - L + BRIDGED L - R + R - L + BRIDGED CH1, 2 CH3, 4 Make the speaker connections using speaker wire that is at least 16 gauge or heavier. As with any audio component, proper phasing of the amplifier and speakers is essential for strong bass response. When connecting, make sure that positive (+) from the amplifier is conne ...
-
Profile 100SX - page 11
B + REM GND FUSE L - R + R - L + BRIDGED L - R + R - L + BRIDGED CH1, 2 CH3, 4 + + - - + + - - 4 Ohm Speaker 4 Ohm Speaker 4 Ohm Speaker 4 Ohm Speaker L - R + R - B + REM GND FUSE L + BRIDGED + + - - 4 Ohm Speaker 4 Ohm Speaker TWO CHANNEL BRIDGED SPEAKER CONNECTIONS FOUR CHANNEL BRIDGED SPEAKER CONNECTIONS S PEAKER CONNECTIONS (BRIDGED) The Califo ...
-
Profile 100SX - page 12
CAUTION! In Tri- mode operation, the amplifier must see a 2 Ohm load or higher for the stereo satellites and no lower than 4 Ohms for the subwoofer(s). Any lower than the above mentioned impedance will cause the amplifier to overheat and possibly cause permanent damage to the amplifier. S PEAKER CONNECTIONS (TRI-MODE) L - R + R - B + REM GND FUSE L ...
-
Profile 100SX - page 13
MIN MAX LEVEL FIL TER X-OVER BASS BOOST 40Hz 130Hz 0dB 12dB LOW HI OFF Select your crossover type and frequency. . (Please note: If you intend to u se the amplifier in the Tri-mode configuration, it is necessary to set the crossover control to the “Flat” setting in order to receive full range output) The California amplifiers are equipped with ...
-
Profile 100SX - page 14
T ROUBLE SHOOTING THE SYSTEM We have put together this trouble-shooting guide if you experience problems after installing the amplifier. Please keep in mind that the majority of problems incurred are caused by improper installation and not the equipment itself. In addition, there are many components in the system that could cause various signal pro ...
-
Profile 100SX - page 15
S PECIFICATIONS 100SX O u t p u t P o w e r @ 4 O h m..................................................2 x 7 0 W A T T S R M S ....................................................2 x 3 5 W A T T S R M S ....................................................2 x 5 0 W A T T S B r i d g e d R M S @ 4 O h m................................................ ...
-
Profile 100SX - page 16
15 600SX ....................................................2 x 1 5 0 W A T T S R M S ...................................................2 x 2 2 5 W A T T S B r i d g e d R M S @ 4 O h m..................................................1 x 4 5 0 W A T T S T H D @ R M S P o w e r ..................................................................... ...
-
Profile 100SX - page 17
440SX ....................................................4 x 5 0 W A T T S R M S ....................................................4 x 7 5 W A T T S B r i d g e d R M S @ 4 O h m..................................................2 x 1 5 0 W A T T S T H D @ R M S P o w e r ........................................................................< ...
-
Profile 100SX - page 18
LIMITED WARRANTY Profile Consumer Electronics, Inc. warrants this product to be free from defects in material and workmanship for a period of One (1) Year from the date of sale to the original consumer purchaser. If this product is proven to be defective within this one year period, Profile will repair it when said product is returned, with a copy ...
-
Profile 100SX - page 19
WARRANTY REPAIR POLICY In the unlikely event of product failure, the following procedures should be followed 1) The unit must be under the 1-year warranty period. 2) The unit must have no physical damage. 3) A copy of the original proof of purchase must be sent with the unit. 4) Include a brief description of the problem or failure with the unit. 5 ...
-
Profile 100SX - page 20
PROFILE CONSUMER ELECTRONICS, INC. 15060 SHOEMAKER AVE SANTA FE SPRINGS, CA 90670 TEL: (562) 404-9393 FAX: (562) 404-9433 WWW.PROFILEUSA.COM By ...
Avez-vous une question à propos de Profile 100SX?
Utiliser le formulaire ci-dessous
Si vous n’avez pas résolu votre problème avec Profile 100SX, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Profile 100SX il est probable qu’il a envie de partager la façon de le résoudre.