-
Hoover U4001 - page 1
Hoover,® Convertible Cleaner Model U4001 Owners Manual ...
-
Hoover U4001 - page 2
HOW TO ASSEMBLE YOUR NEW HOOVER CLEANER ASSEMBLE HANDLE PIECES Remove cardboard from end of handle pieces. Slide the two handle pieces together. Check to see that cord clips are on the same side of the handle. Insert bolt through small holes and secure with nut. Tighten nut with screwdriver. If the nut and bolt are not assembled as shown in the ill ...
-
Hoover U4001 - page 3
HOW TO ATTACH OUTER JACKET TO CLEANER Place the two projections at the bottom of the outer bag assembly inside the wire loops at the back of the cleaner. Pull the bag clip to tile left and fit bag against opening. When you release the bag clip, make sure that it fits completely over the bag lock. Attach the spring to the support hook, which is loca ...
-
Hoover U4001 - page 4
To turn d.p,, cleaner on, _ push switch down. To turn cleaner off, pull the| switch up. ._ HANDLE ADJUSTMENTS The handle on your cleaner has three positions storage, operating, and low (for reaching under low furniture). The handle can be lowered by stepping on pedal at the left rear of cleaner. The handle stiould always be in storage posit ...
-
Hoover U4001 - page 5
DELUXE CLEANING SET: Vinyl Hose and Converter, Telescoping Extension Wand, Crevice Tool, Upholstery Nozzle, Dusting Brush, and Bare Floor Brush. STANDARD CLEANING SET: Vinyl Hose and Converter, Extension Wand, Crevice Tool, and Upholstery Brush. USING YOUR ATTACHMENTS NOTE; When using tools, select SHAG RUG POSITION on cleaner. You can convert your ...
-
Hoover U4001 - page 6
TO CONNECT CONVERTER TO CLEANER Tilt the cleaner so the underside is visible. Insert the converter in the track on the underside of the cleaner. Push converter all the way in to the red line. It is not necessary to remove the belt. TELESCOPING WAND* When you require extra length for cleaning bare floors or hard to reach places, attach the telescopi ...
-
Hoover U4001 - page 7
MANY USES FOR CLEANING ATTACHMENTS Vinyl Hose Hose has vinyl jacket for long, trouble-free life. Floor Brush* All hard floors and carpeted stairs. Upholstery Nozzle or Upholstery Brush Upholstered furniture, draperies, tapestries, mattresses, clothing, automobile interiors, carpeted stairs. Dusting Brush* Carved furniture, table tops, books, lamps, ...
-
Hoover U4001 - page 8
HELPFUL INSTRUCTIONS ON USING YOUR CLEANER EASY TO CARRY. Your cleaner has a convenient carrying handle located underneath the handle bail. DON'T PICK UP HARD, SHARP OBJECTS. with the cleaner. They may damage the belt, the moving parts, and the bag. TAKE CARE OF THE CORD 1. Wind it loosely on cord hooks to avoid unnecessary strain. 2. Grasp th ...
-
Hoover U4001 - page 9
NOTE: Disconnect cord before replacing parts. THE BAG Your Hoover cleaner has a durable outer jacket which covers the throw-away bag. A light wiping with a damp cloth will keep this outer jacket clean. To assure that your Hoover cleaner operates at peak performance it is imperative that you use only genuine Hoover throw-away filter bags made by The ...
-
Hoover U4001 - page 10
THE BELT The belt of your Hoover cleaner controls the speed of the rug agitator and is important for the efficient operation of your cleaner. Be- cause of this, it is important when buying a new belt that you always insist on a genuine Hoover belt. Some other belts on the market, not manufactured under Hoover design and quality controls, do not ope ...
-
Hoover U4001 - page 11
4 Lift out rug agitator, remove old belt and place new belt in groove of rug agitator. 5 Replace agita- tor. On one end of the agitator roll there is a raised metal platb. Make sure that this end is placed in groove on side of cleaner. 6 Place belt on pulley. Side of belt nearest cleaner should be in line with arrow on bottom of cleaner. 7 Replace ...
-
Hoover U4001 - page 12
THE BRUSHES When brushes are worn and bristles do not touch the edge of a card held across the nozzle, they should be replaced. Always replace both brushes at the same time to maintain cleaning efficiency. TO REPLACE THE BRUSHES 1 (Disconnect the Cleaner from Electrical Outlet) before re- placing brushes. To replace worn brushes, remove bottom plat ...
-
Hoover U4001 - page 13
SERVICE Service and genuine Hoover replacement parts may be obtained from Hoover Factory Service Stations, or Authorized Warranty Service Dealers, as listed on white insert. For service in Warranty, follow instructions set forth in Guarantee. When ordering new parts, make sure that you always mention the model number of the product. Lubrication: Th ...
-
Hoover U4001 - page 14
UPRIGHT VACUUM CLEANER WARNING: ELECTRIC SHOCK COULD OCCUR IF USED OUTDOORS OR ON WET SURFACES. • Avoid picking up hard, sharp objects with the cleaner. They may damage the belt, moving parts, and the bag. • Do not use cleaner to pick up matches or cig- arette butts. • Change bag frequently when picking up very fine materials such as powder. ...
-
Hoover U4001 - page 15
INDEX ADJUSTING CLEANER TO RUG ........................ 4 ASSEMBLING CLEANER ............................. 2-3 ATTACHMENTS .................................... 5-7 BELT ............................................ 10-11 BRUSHES .......................................... 12 HANDLE ADJUSTMENTS .............................. 4 HELPFUL HINTS .......... ...
Avez-vous une question à propos de Hoover U4001?
Utiliser le formulaire ci-dessous
Si vous n’avez pas résolu votre problème avec Hoover U4001, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Hoover U4001 il est probable qu’il a envie de partager la façon de le résoudre.