Français dropdown-ico

Manuel d’utilisation Snapper NZMJ25612KH, NZMJ23522KH

40 pages 5.26 mb
Télécharger

Aller à la page of 40

Summary
  • Snapper NZMJ25612KH, NZMJ23522KH - page 1

    Safety Instructions & Operator’s Manual for MID MOUNT Z-RIDER ZERO TURNING HYDRO DRIVE SERIES 2 MODELS NZMJ23522KH NZMJ25612KH MODEL NUMBER EXPLANATION N Z MJ 23 52 2 KH MODEL DESIGNATION ENGINE TYPE DRIVE SYSTEM TYPE SERIES DESIGNATION MOWER ORIENTATION MOWER DECK SIZE ENGINE HP * POWER UNIT N – Model Designation 23 – Engine Horse Power ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 2

    2 IMPORTANT SAFETY INSTRUCTIONS WARNING: This pow erful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply w ith the follow ing SAFETY instructions could result in serious injury or death to the operator or other persons. The owner of the machine must understand these in ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 3

    3 IMPORTANT SAFETY INSTRUCTIONS PREPARATION (Continued From Previous Page) 2. Only mature, responsible persons shall operate or service the machine and only after proper instruction and training. The ow ner is responsible for training the operators. Further, the ow ner/operator can prevent and/or is responsible for accidents or injuries occurring t ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 4

    4 IMPORTANT SAFETY INSTRUCTIONS OPERATION (Continued From Previous Page) 8. Keep hands and feet aw ay from rotating blades underneath deck. DO NOT place foot on ground w hile BLADES are ON or machine is in motion. 9. DO NOT operate machine w ithout entire grass catcher or guards in place. DO NOT point discharge at people, passing cars, w indow s or ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 5

    5 TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIO NS ........................................................................ 2-4 TABLE OF CO NTENTS ..................................................................................................... 5 SECTION 1 - FAMI LIARIZATI ON ..................................................................... ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 6

    6 Section 1 - FAMILIARIZATION 1. 1 INTRODUCTION This manual has been prepared for the operator’s of the SNAPPER MID MOUNT Z-RIDER. Its purpose, aside from recommending standard operating procedures and routine service requirements, is to promote SAFETY through the use of accepted operating practices. Read, Understand and Follow the IMPORTANT SAFE ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 7

    7 Section 2 – SAFETY MESSAGES AND SYMBOLS DANGER ! ROTA TING PA RTS KEEP AWA Y FROM MO VING PA RTS MOTION CONTROL LEVER (JOYSTICK) MULTI-DIRECTIONAL PARKING BRA KE LEVER OPERA TION WARNING ! A VOID SERIOUS INJURY OR DEA TH STARTING, OPERA TION & STOPPING OF MA CHINE WEAR HEA RING PROTECTION FORWARD REVERSE ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 8

    8 Section 2 – SAFETY MESSAGES AND SYMBOLS DANGER! ROTA TING BLA DES KEEP CHILDREN AND O THERS OUT OF MOWING A REA DANGER! ROTA TING BLA DES KEYSWITCH HOUR METER PULL SWITCH “UP” TO ENGA GE BLA DES PUSH SWITCH “DOWN” TO DISENGA GE BLA DES CHOKE CONTROL ENGINE SPEED CONTROL CONTROL PANEL IDENTIFICA TION FAST SLOW RUN OFF/STOP START IGNITION ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 9

    9 WARNING DO NOT allow operation of the machine by untrained personnel. Section 3 - OPERATING INSTRUCTIONS 3.1 PRE-START CHECK LIST Make the following checks and perform the service required before each start-up. 3.1.1. Check tires and add or release air as needed to bring pressure to 12 psi in drive tires. Pressure in front caster wheels should be ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 10

    10 Section 3 - OPERATING INSTRUCTIONS ROLL RELEASE: To roll the machine without the engine running, pressure w ithin the hy draulic pumps must be released. There is a hydraulic pressure relief valve on the upper side of each pump that is used to release the pressure. Use a w rench to rotate both relief valves counter clockwise tw o full turns to op ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 11

    11 Section 3 - OPERATING INSTRUCTIONS 3.2.1. STARTING ENGINE NOTE: If after 5 seconds of cranking the engine does not start, release the key. Attempt starting again after waiting for approximately 20 seconds. 7. After engine starts, move the choke control to the “OFF” or no choke position. Allow a brief warm-up until engine runs smooth. 3.2.2. ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 12

    12 Section 3 - OPERATING INSTRUCTIONS 3.3 CUTTING HEIGHT ADJUSTMENT 1. Adjust cutting height, as desired, to any position, using deck lift lever. The release latch should be pulled up when lowering the deck. When raising the deck, the release latch does not have to be pulled up. IMPORTANT: There is a foot assist pedal located to the right front si ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 13

    13 Section 3 - OPERATING INSTRUCTIONS 3.4.2. STOPPING MACHINE 1. Return motion control lever to the center neutral position. IMPORTANT: Operator must use hand assistance to bring the motion control lever to the neutral position FIGURE 3.12 2. Engage parking brake. 3. Push Blade Switch down to the “OFF” position to disengage or turn “OFF” th ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 14

    14 Section 4 - MAINTENANCE 4.1 INTRODUCTION To retain the quality of the SNAPPER mower, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular SNAPPER mower, always mention the model and serial number. SNAPPER recommends returning the mower to ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 15

    15 Section 4 - MAINTENANCE 4.2.3. CHECK MOWER DRIVE BELT 1. Lower deck to lowest setting. 2. Remove footrest. See Figure 4.3. 3. Removal of footrest will allow access to deck belt. 4. Check the belt tension. The idler pulleys and springs provide proper belt tension and require no adjustments. If belt is frayed, slit, severed or belt strands exposed ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 16

    16 Section 4 - MAINTENANCE 4.3.3. RIDING MO WER - LUBRICATION 1. Front Wheel Bearings Lubricate with Kendall NLGI No. 2 lithium grease or equivalent, from a grease gun. See Figure 4.5. FIGURE 4.5 2. Hydro Pumps Check the level of the fluid in both of the fluid reservoirs. Wipe away all dirt and debris from around reservoir cap before removing. Oil ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 17

    17 Section 4 - MAINTENANCE WARNING Allow engine to cool for at least ten minutes before performing service or maintenance. DO NOT smoke near fuel components w hen performing service or maintenance. DO NOT perform service and maintenance near an open flame. Wipe off any spilled fuel before starting engine. DO NOT run engine indoors. 4.5 ANNUALLY (EN ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 18

    18 Section 4 - MAINTENANCE WARNING DO NOT attempt any maintenance, adjustments or service with engine running. STOP engine. STOP blades. Set parking brake. Remove key . Remove spark plug w ires and secure aw ay from spark plugs. Engine and components are HOT. Avoid serious burns, allow sufficient time for all parts to cool. 4. 6 DE C K RE M OV AL ( ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 19

    19 Section 5 - ADJUSTMENTS & REPAIR DANGER Exercise EXTREME CAUTION w hen making this adjustment, due to close proximity of mov ing parts. 5.1 NEUTRAL POSITION ADJUSTMENTS The motion control lever controls the movement and stopping of the machine. Move the control lever to the center or neutral position to stop machine. Engage the parking brake ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 20

    20 Section 5 - ADJUSTMENTS & REPAIR 5.1 NEUTRAL POSITION ADJUSTMENTS (Continued From Previous Page) 12. Move motion control lever to the neutral position and engage the parking brake, See Fi gu r e 3. 7, hold connecting rod up to the activation assembly and check length of rod. Tie rod end bolt must align with the activation assembly. If bolt i ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 21

    21 Section 5 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any maintenance, adjustments or service with engine running. STOP engine. STOP blades. Set brake. Remove key. Remov e spark plug w ires and secure aw ay from spark plugs. Engine and components are HOT. Avoid serious burns, allow sufficient time for all parts to cool. 5.2.1. MOWER DECK A ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 22

    22 Section 5 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any maintenance, adjustments or service with engine running. STOP engine. STOP blades. Set brake. Remove key. Remov e spark plug w ires and secure aw ay from spark plugs. Engine and components are HOT. Avoid serious burns, allow sufficient time for all parts to cool. 5.3 TRACTION BELT T ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 23

    23 Section 5 - ADJUSTMENTS & REPAIR 5.6 MOWER DRIVE BELT REPLACEMENT Inspect mower drive belt. Replace belt if it shows signs of excessive wear, damage and/or is broken. 5.6.1. BELT REMOVAL 1. Remove power unit footrest. 2. The engine to deck belt must be removed before the deck belt can be removed. Remove engine to deck belt. 3. Disconnect dec ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 24

    24 Section 5 - ADJUSTMENTS & REPAIR 5.7 ENGINE ADJUSTMENTS & REPAIR Refer to the engine owner’s manual for engine adjustments and/or repairs. 5.8 MOWER BLADE REPLACEMENT 5.8.1. BLADE WEAR LIMITS 1. Inspect blade frequently for signs of excessive wear or damage. Replace blade when it reaches the wear limit. See Figure 5.13. 5.8.2. BLADE SH ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 25

    25 Section 5 - ADJUSTMENTS & REPAIR WARNING Shield the positive terminal w ith terminal cover located on battery harness. This prevents metal from touching the positive terminal, w hich could cause sparks. Cables must be connected to battery terminals in the proper position. RED (Positive) cable must go to the ( + ) terminal. BLACK (Negative) c ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 26

    26 Section 5 - ADJUSTMENTS & REPAIR 5.9.4. BATTERY TESTING 1. Remove battery. Refer to Section “BATTERY REMOVAL”. 2. Using a voltmeter, check the battery’s state of charge by comparing the voltmeter reading with the chart below. (Remember to hook the positive (red) lead of the voltmeter to the battery’s positive terminal, and the negati ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 27

    27 Section 5 - ADJUSTMENTS & REPAIR 5 . 1 0 MOWER SPINDLES (Field Serviceable Spindles) BEARING REPLACEMENT In the event that a spindle bearing requires replacement, the SNAPPER Field Serviceable Spindles have been designed so that no special tools or presses are required. 1. Remove belt. Loosen blade nut and remove. Allow blade bolt, washer, b ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 28

    28 Section 5 - ADJUSTMENTS & REPAIR 5.11 HYDRAULIC SYSTEM, PURGING After replacing or repairing hydraulic system components, one or both of the wheel drives may not pull properly. This is likely to be caused by air entrapped in the system. If you experience a pulling issue after completing repairs, perform the following procedure to purge the a ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 29

    29 TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Starter Will Not Crank 1. Battery dead. 1. Service battery. Engine 2. Blown fuse. 2. Replace fuse. 3. Electrical connections loose or corroded. 3. Cl ean and check connections for good contact. 4. Defective ignition switch. 4. Contact authorized SNA PPER dealer. Engine Will Not Start 1. Bl ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 30

    30 TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Machine Will Not Move 1. Motion Control Lever in the neut ral “N” position. 1. Move Moti on Control to desired speed position. Loss Of Traction 2. Hydro. Pumps in roll release setting. 2. Ti gh t en r el i ef va l ve s . 3. Low transmission hy draulic oil level. 3. Bring hydraulic oil ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 31

    31 SERVICE SCHEDULE ITEM SERVICE PERFORMED REF. NUMBER EACH USE 5 HRS 25 HRS 50 HRS 100 HRS EACH SEASON Engine Oil Check Oil Level Page 9 X Initial Oil Change Page 14 X Periodic Oil Change Page 15 X* Air Cleaner Clean or Replace Engine Manual X** Spark Plug Replace Engine Manual X Fuel Filter Replace Page 17 X Engine Cooling System Clean Shroud &am ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 32

    32 2 YEAR LIMITED WARRANTY For two (2) years from purchase date for the original purchaser's use, SNAPPER , through any authorized SNAPPER dealer will replace, free of charge (except for taxes where applicable), any part or parts found upon examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both. Fo ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 33

    33 PRIMARY MAINTENANCE ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 34

    34 PRIMARY MAINTENANCE ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 35

    35 PRIMARY MAINTENANCE ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 36

    36 PRIMARY MAINTENANCE ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 37

    37 SNAPPER PRODUCT REGISTRATION FORM IMPORTANT: KEEP THIS INFORMATION FOR YOUR PERSONAL RECORDS (Complete the following informa tion on your Snapper purchase) Model Number __________________________________________________________ Serial Number __________________________________________________________ Date of Pu rchase ____________________________ ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 38

    38 NOTES ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 39

    39 NOTES ...

  • Snapper NZMJ25612KH, NZMJ23522KH - page 40

    40 Safety Instructions & Operator’s Manual for MID MOUNT Z-RIDER ZERO TURNING HYDRO DRIVE SERIES 2 IMPORTANT Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contai n very important emissions information and critical safety warnings. Read, ...

Fabricant Snapper Catégorie Lawn Mower

Les documents que nous recevons du fabricant de l'appareilSnapper NZMJ25612KH, NZMJ23522KH peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Snapper
- manuels d’utilisations NZMJ25612KH, NZMJ23522KH
- fiches produit Snapper
- dépliants
- ou étiquettes-énergie Snapper NZMJ25612KH, NZMJ23522KH
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Snapper NZMJ25612KH, NZMJ23522KH.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Snapper NZMJ25612KH, NZMJ23522KH, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Snapper NZMJ25612KH, NZMJ23522KH. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Snapper NZMJ25612KH, NZMJ23522KH.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Snapper NZMJ25612KH, NZMJ23522KH, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Snapper NZMJ25612KH, NZMJ23522KH par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Snapper NZMJ25612KH, NZMJ23522KH.

Le manuel d’utilisation complet Snapper, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Snapper NZMJ25612KH, NZMJ23522KH - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Snapper NZMJ25612KH, NZMJ23522KH, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lSnapper NZMJ25612KH, NZMJ23522KH qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Snapper NZMJ25612KH, NZMJ23522KH - qui devraient nous aider dans les premières étapes lors de l'utilisation Snapper NZMJ25612KH, NZMJ23522KH
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Snapper NZMJ25612KH, NZMJ23522KH
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Snapper NZMJ25612KH, NZMJ23522KH dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Snapper NZMJ25612KH, NZMJ23522KH?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Snapper NZMJ25612KH, NZMJ23522KH, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Snapper NZMJ25612KH, NZMJ23522KH il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)