Français dropdown-ico

Manuel d’utilisation Chamberlain 2500D

36 pages 2.56 mb
Télécharger

Aller à la page of 36

Summary
  • Chamberlain 2500D - page 1

    Owner’s Manual ■ Please read this manual and the enclosed safety materials carefully! ■ Fasten the manual near the garage door after installation. ■ The door WILL NOT CLOSE unless The Protector System ® is connected and properly aligned. ■ Periodic checks of the opener are required to ensure safe operation. ■ The model number label is ...

  • Chamberlain 2500D - page 2

    2 Introduction 2-5 Safety symbol review and signal word review ............2 Preparing your garage door ........................................3 T ools ............................................................................3 Planning .....................................................................4 Carton inventory ...................... ...

  • Chamberlain 2500D - page 3

    3 Preparing your garage door Before you begin: • Disable locks. • Remove any ropes connected to garage door . • Complete the following test to make sure your garage door is balanced and is not sticking or binding: 1. Lift the door about halfway as shown. Release the door . If balanced, it should stay in place, supported entirely by its spring ...

  • Chamberlain 2500D - page 4

    Sa f et y R eversin g Sensor Hori z ontal and vertical rein f orcement is needed f or li g htwei g ht g ara g e doors ( f iber g lass, steel, aluminum, door with g lass panels, etc . ) . See pa g e 2 0 f or details . Header Wall Sa f et y R eversin g Sensor Support bracket & f astenin g hardware is re q uired . See pa g e 13 . FINI SHED CE I L ...

  • Chamberlain 2500D - page 5

    5 Strai g ht Door Arm Section Curved Door Arm Section Header Bracket U P C E I L IN G M O U N T O N L Y 2 - Conductor Bell Wire White & White/ R ed Sa f et y Labels and Literature R emote Control Transmitter V isor Clip Door Bracket SECU RI TY ✚ ® 3 - Button R emote Control (2) Sa f et y R eversin g Sensors (1 Sendin g E y e and 1 R eceivin ...

  • Chamberlain 2500D - page 6

    ASSEMBL Y STEP 1 Attach the Rail to the Motor Unit T o avoid installation difficulties, do not run the garage door opener until instructed to do so. • Remove the two washered bolts mounted in top of motor unit. • Align rail and styrofoam over sprocket. Cut tape from rail, belt and styrofoam. • REMOVE STYROFOAM. • Insert both washered bolts ...

  • Chamberlain 2500D - page 7

    ASSEMBL Y STEP 3 Attach the Belt Cap Retainer • Position the belt cap retainer over the opener sprocket so the two holes in cap align with the two holes in mounting plate. Attach with #8x3/8" hex screws provided. Y ou have now finished assembling your garage door opener . Please read the following warnings before proceeding to the installati ...

  • Chamberlain 2500D - page 8

    8 INST ALLA TION STEP 1 Determine the Header Bracket Location Installation procedures vary according to garage door types. Follow the instructions which apply to your door . SECTIONAL DOOR AND ONE-PIECE DOOR WITH TRACK 1. Close the door and mark the inside vertical centerline of the garage door . 2. Extend the line onto the header wall above the do ...

  • Chamberlain 2500D - page 9

    9 ONE-PIECE DOOR WITHOUT TRACK 1. Close the door and mark the inside vertical centerline of your garage door . Extend the line onto the header wall above door , as shown. If headroom clearance is minimal, you can install the header bracket on the ceiling. See page 10. If you need to install the header bracket on a 2x4 (on wall or ceiling), use lag ...

  • Chamberlain 2500D - page 10

    10 INST ALLA TION STEP 2 Install the Header Bracket Y ou can attach the header bracket either to the wall above the garage door , or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the header bracket over drywall. If installing into masonry , use concrete anchors (not provided). W ALL HE ...

  • Chamberlain 2500D - page 11

    Header Bracket Belt Pulley Bracket Opener Carton or Temporary Support Header Wall Garage Door Clevis Pin 5/16"x2-3/4" Ring Fastener Torsion Spring Rail Clevis Pin 5/16"x2-3/4" Ring Fastener Header Bracket Belt Pulley Bracket Foam Packaging Rail 11 HARDW ARE SHOWN ACTUAL SIZE INST ALLA TION STEP 3 Attach the Rail to the Header Br ...

  • Chamberlain 2500D - page 12

    12 ONE-PIECE DOOR WITHOUT TRACK A 2x4 on its side is convenient for setting an ideal door-to-rail distance. • Remove foam packaging. • Raise the opener onto a stepladder . Y ou will need help at this point if the ladder is not tall enough. • Open the door all the way and place a 2x4 on its side on the top section of the door beneath the rail. ...

  • Chamberlain 2500D - page 13

    13 INST ALLA TION STEP 5 Hang the Opener Three representative installations are shown. Y ours may be different. Hanging brackets should be angled, Figure 1, to provide rigid support. On finished ceilings, Figure 2, attach a sturdy metal bracket to structural supports before installing the opener . This bracket and fastening hardware are not provide ...

  • Chamberlain 2500D - page 14

    T o prevent possible SERIOUS INJURY or DEA TH from electrocution: • Be sure power is not connected BEFORE installing door control. • Connect ONL Y to 24 VOL T low voltage wires. T o prevent possible SERIOUS INJURY or DEA TH from a closing garage door: • Install door control within sight of garage door , out of reach of children at a minimum h ...

  • Chamberlain 2500D - page 15

    15 INST ALLA TION STEP 7 Install the Lights and Lens Press the release tabs on both sides of lens. Gently rotate lens back and downward until the lens hinge is in the fully open position. Do not remove the lens. • Install up to a 100 watt maximum light bulb in each socket. The lights will turn ON and remain lit for approximately 4-1/2 minutes whe ...

  • Chamberlain 2500D - page 16

    INST ALLA TION STEP 9 Electrical Requirements T o avoid installation difficulties, do not run the opener at this time. T o reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug doesn't fit into the outlet you have, conta ...

  • Chamberlain 2500D - page 17

    17 Invisible Light Beam Protection Area Sensor Beam 6" (15 cm) max. above floor Sensor Beam 6" (15 cm) max. above floor Facing the door from inside the garage INST ALLA TION STEP 10 Install The Protector System ® The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direct ...

  • Chamberlain 2500D - page 18

    18 DOOR TRACK MOUNT (RIGHT SIDE) I ndicator L ig h t L ens L ip Sensor Bracket Door Track FLOOR MOUNT (RIGHT SIDE) WALL MOUNT (RIGHT SIDE) I ndicator L ig h t Sensor Bracket L ens E xtension Bracket ( See A ccessories ) I nside G arage W all ( Provided w it h E xtension Bracket ) ( Provided w it h E xtension Bracket ) Figure 1 Figure 2 Figure 3 Fig ...

  • Chamberlain 2500D - page 19

    19 I nvisi b le L ig h t Beam Protection A rea Sensor Sensor Bell Wire Bell Wire Finished Ceiling Q uick-Connect Terminals Strip w ire 7 /16" 7 /16" Sensor Connections Connect Wire to Q uick-Connect Terminals W h ite/ b lack w ire W h ite w ire Red Grey W h ite Carriage Bolt 1/4"-2 0 x1/2" L ens Wing N ut Figure 5 Figure 6 MOUNT ...

  • Chamberlain 2500D - page 20

    20 INST ALLA TION STEP 11 Fasten the Door Bracket Follow instructions which apply to your door type as illustrated below or on the following page. A horizontal reinforcement brace should be long enough to be secured to two or three vertical supports. A vertical reinforcement brace should cover the height of the top panel. Figure 1 shows one piece o ...

  • Chamberlain 2500D - page 21

    21 ONE-PIECE DOORS Please read and comply with the warnings and reinforcement instructions on the previous page. They apply to one-piece doors also. • Center the door bracket on the top of the door , in line with the header bracket as shown. Mark either the left and right, or the top and bottom holes. • Metal Doors: Drill 3/16" pilot holes ...

  • Chamberlain 2500D - page 22

    INST ALLA TION STEP 12 Connect Door Arm to T rolley Follow instructions which apply to your door type as illustrated below and on the following page. SECTIONAL DOORS ONL Y Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolley . Slide the outer trolley back (away from the door ...

  • Chamberlain 2500D - page 23

    ALL ONE-PIECE DOORS 1. Assemble the Door Arm: • Fasten the straight and curved door arm sections together to the longest possible length (with a 2 or 3 hole overlap). • Make sure the garage door is fully closed. Connect the straight door arm section to the door bracket with the 5/16"x1-1/4" clevis pin. • Secure with a ring fastener ...

  • Chamberlain 2500D - page 24

    4. Open and close the door with the remote control or door control 2 or 3 times. • If the door does not stop in the desired UP (open) position or reverses before the door stops at the DOWN (close) position, proceed to Adjustment Step 2 Setting the Force. • If the door stops in both the desired UP (open) and DOWN (close) positions, proceed to Ad ...

  • Chamberlain 2500D - page 25

    ADJUSTMENT STEP 2 Setting the Force The force setting button is located on the back panel of the motor unit. The force setting measures the amount of force required to open and close the door . 1. Locate the orange button on the back panel of unit (Figure 1) . 2. Push the orange button twice to enter unit into Force Adjustment Mode (Figure 2). The ...

  • Chamberlain 2500D - page 26

    ADJUSTMENT STEP 3 T est the Safety Reversal System TEST • With the door fully open, place a 1-1/2" board (or a 2x4 laid flat) on the floor , centered under the garage door . • Operate the door in the down direction. The door must reverse on striking the obstruction. Upon successful safety reversal test proceed to Adjustment Step 4 . ADJUST ...

  • Chamberlain 2500D - page 27

    OPERA TION 27 Using Y our Garage Door Opener Y our Security ✚ ® opener and hand-held remote control have been factory programmed to a matching code which changes with each use, randomly accessing over 100 billion new codes. Y our opener will operate with several Security ✚ ® remote controls utilizing up to 12 functions, and one Security ✚ ? ...

  • Chamberlain 2500D - page 28

    28 Using the W all-Mounted Door Control THE MOTION DETECTING DOOR CONTROL Press the push bar to open or close the door . Press again to reverse the door during the closing cycle or to stop the door while it's opening. This door control contains a motion detector that will automatically turn on the light when it detects a person entering the ga ...

  • Chamberlain 2500D - page 29

    29 CARE OF YOUR OPENER MAINTENANCE SCHEDULE Once a Month • Manually operate door . If it is unbalanced or binding, call a trained door systems technician. • Check to be sure door opens & closes fully . Adjust limits and/or force if necessary . (See pages 24 and 25) • Repeat the safety reverse test. Make any necessary adjustments. (See Adj ...

  • Chamberlain 2500D - page 30

    30 Having a Problem? (Continued) 6. The garage door opens and closes by itself: • Be sure that all remote control push buttons are off. • Remove the bell wire from the door control terminals and operate from the remote only . If this solves the problem, the door control is faulty (replace), or there is an intermittent short on the wire between ...

  • Chamberlain 2500D - page 31

    *3-Button Remotes If provided with your garage door opener , the large button is factory programmed to operate it. Additional buttons on any Security ✚ ® 3-Button remote or mini-remote can be programmed to operate other Security ✚ ® garage door openers. T o Erase All Codes From Motor Unit Memory T o deactivate any unwanted remote, first erase ...

  • Chamberlain 2500D - page 32

    1. Enter a four digit personal identification number (PIN) of your choice on the keypad. Then press and hold ENTER. 2. While holding the ENTER button, press and hold the LIGHT button on the Motion Detecting Control Panel. 3. Continue holding the ENTER and LIGHT buttons while you press the push bar on the Motion Detecting Control Panel (all three bu ...

  • Chamberlain 2500D - page 33

    7 10 11 6 5 N O TIC E U P C E I L I N G M O U N T O N L Y 8 1 4 2 3 9 12 L O C K L IG H T 2 1 5 6 3 7 8 4 Rail Assembly Parts Installation Parts 33 KEY P ART NO. NO. DESCRIPTION 1 4A1008 Master link kit 2 41A5424 Belt pulley bracket 3 41B3869-1 Complete trolley assembly 4 109B33 T rolley clip 5 183B99 One-piece T -rail 6 41A5434-1 1 Full belt assem ...

  • Chamberlain 2500D - page 34

    Motor Unit Assembly Parts 34 2 3 4 5 6 7 8 9 10 11 12 1 KEY P ART NO. NO. DESCRIPTION 1 41C76 Belt cap and sprocket 2 41B4245-1 Line cord 3 41B4375-3 T erminal block w/screws 4 41C5317-1 Wire harness (logic) 41C5839 High voltage wire harness 41B5806-1 DC motor wire harness 41C5418 Light socket wire harness 5 41D605-1 Motor 80kg/100kg KEY P ART NO. ...

  • Chamberlain 2500D - page 35

    35 LOCK LIGHT C LO SE D O P E N ACCESSORIES 974LM 970LM 995LM 2778BD 41A5281 1702LM Outside Quick Release: Required for a garage with NO access door . 8 Foot Complete Rail: T o allow an 8 foot door to open fully . Remote Light Control: Enables homeowner to turn on a lamp, television or other appliance from their car with their garage door opener re ...

  • Chamberlain 2500D - page 36

    © 2004, The Chamberlain Group, Inc. 1 14A2933B All Rights Reserved Printed in Mexico LIFTMASTER SER VICE IS ON CALL OUR LARGE SERVICE ORGANIZA TION SP ANS AMERICA INST ALLA TION AND SERVICE INFORMA TION IS AS NEAR AS YOUR TELEPHONE SEVEN DA YS A WEEK. SIMPL Y DIAL OUR TOLL FREE NUMBER: 1-800-528-2817 HOURS: (Central Standard Time) 6:00 A.M. TO 7:0 ...

Fabricant Chamberlain Catégorie Garage Door Opener

Les documents que nous recevons du fabricant de l'appareilChamberlain 2500D peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Chamberlain
- manuels d’utilisations 2500D
- fiches produit Chamberlain
- dépliants
- ou étiquettes-énergie Chamberlain 2500D
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Chamberlain 2500D.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Chamberlain 2500D, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Chamberlain 2500D. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Chamberlain 2500D.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Chamberlain 2500D, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Chamberlain 2500D par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Chamberlain 2500D.

Le manuel d’utilisation complet Chamberlain, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Chamberlain 2500D - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Chamberlain 2500D, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lChamberlain 2500D qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Chamberlain 2500D - qui devraient nous aider dans les premières étapes lors de l'utilisation Chamberlain 2500D
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Chamberlain 2500D
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Chamberlain 2500D dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Chamberlain 2500D?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Chamberlain 2500D, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Chamberlain 2500D il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)