Français dropdown-ico

Manuel d’utilisation Stanley Black & Decker CS05

26 pages 2.94 mb
Télécharger

Aller à la page of 26

Summary
  • Stanley Black & Decker CS05 - page 1

    © 2014 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 66864 7/2014 V er . 8 USER MANUAL Safety , Operation and Maintenance CS05/CS06 HYDRAULIC CHAIN SA W ...

  • Stanley Black & Decker CS05 - page 2

    ...

  • Stanley Black & Decker CS05 - page 3

    CS05/CS06 User Manual ◄ 3 WARNING SERIOUS INJUR Y OR DEA TH COULD RESUL T FROM THE IMPROPER REP AIR OR SERVICE OF THIS T OOL. REP AIRS AND / OR SERVICE T O THIS TOOL MUST ONL Y BE DONE BY AN AUTHORIZED AND CERTIFIED DEALER. SERVICING: This manual contains safety , operation, and routine maintenance instructions. Stanley Hy- draulic T ools recomme ...

  • Stanley Black & Decker CS05 - page 4

    4 ► CS05/CS06 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte - nance personnel. Safety symbols and signal words, as shown below , are used to ...

  • Stanley Black & Decker CS05 - page 5

    CS05/CS06 User Manual ◄ 5 T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety . Re - view them carefully before operating the tool and before performing general maintenance or rep ...

  • Stanley Black & Decker CS05 - page 6

    6 ► CS05/CS06 User Manual – maintenance instructions for the saw chain. – Only use replacement bars and chains specied by Stanley Hydraulic T ools. Chains must meet the requirements of ANSI B175.1 for low kick - back performance. • Always be well rested and mentally alert before op - erating the chain saw . • Do not allow other persons ...

  • Stanley Black & Decker CS05 - page 7

    CS05/CS06 User Manual ◄ 7 The following guidelines must be followed to prevent accidental contact with overhead electrical conductors and/or communication wires and cables. (ref. ANSI Z133.1-2000) Working in Proximity to Electrical Hazards: An inspection shall be made by a qualied arborist to determine whether an electrical hazard exists befor ...

  • Stanley Black & Decker CS05 - page 8

    8 ► CS05/CS06 User Manual T able 2 – Minimum approach distances to energized conductors for persons other than qualied line-clearance arborists and qualied line-clearance ar - borist trainees. Nominal V oltage kV phase-to-phase 1 Distance ft-in m 0.0 to 1.0 10–00 3.05 1.1 to 15.0 10–00 3.05 15.1 to 36.0 10–00 3.05 36.1 to 50.0 10– ...

  • Stanley Black & Decker CS05 - page 9

    CS05/CS06 User Manual ◄ 9 28323 CE Decal (CE Models Only) 28409 Composite Decal (CE Models Only) D 30 LPM @ 138 BA R EHTMA CA TEGORY 1 1207 Circuit T ype D Decal (CE Models Only) Fa ilure to use hydraulic hose labeled and certified as non-conductive when using hydraulic tool so n or near electric lines ma yr esul ti n deat ho r Fo rp roper and sa ...

  • Stanley Black & Decker CS05 - page 10

    10 ► CS05/CS06 User Manual The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy - draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools. They are: Certied non-conductive — constructed of thermop ...

  • Stanley Black & Decker CS05 - page 11

    CS05/CS06 User Manual ◄ 1 1 Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Utility Bucket T rucks 4-9 15-34 up to 10 up to 3 3/8 10 Both 2250 155 Conductive Hose - Wire Braid or Fiber Braid -DO NOT USE NEAR ELECTRICAL CONDUCT OR ...

  • Stanley Black & Decker CS05 - page 12

    12 ► CS05/CS06 User Manual Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min. operating temperature) T emperature: Sufcient heat rejection capacity to limit max. uid ...

  • Stanley Black & Decker CS05 - page 13

    CS05/CS06 User Manual ◄ 13 OPERA TING PROCEDURES The following are general wood cut ting procedures and techniques. Dif ferences in the terrain, vegetation, and type of wood will make this infor mation more or less val - id for particu lar areas. For advice on specic woodcut - ting problems or techniques for your area, consult your local Stanl ...

  • Stanley Black & Decker CS05 - page 14

    14 ► CS05/CS06 User Manual FELLING OR BACK CUT 4. The felling or back cut is made on the side opposite and at least 2 inches above the hori zontal undercut (the felling cut is made higher as the size of the tree increases). Place the saw so the hand guard is close to the tree trunk and the bucking cleat is dug in. 5. Start the cut horizontally . ...

  • Stanley Black & Decker CS05 - page 15

    CS05/CS06 User Manual ◄ 15 Figure 4. Crosscutting Logs Larger than Bar Length With Pressure on T op LOGS WITH PRESSURE ON TOP (FIGURE 3) 1. Observe all safety precautions. 2. Begin with an upper cut, down from the top. Do not cut too deeply . A cut of about 1/3 of the log diameter is enough. 3. Finish with a bottom cut. They should meet. Figure 3 ...

  • Stanley Black & Decker CS05 - page 16

    16 ► CS05/CS06 User Manual Figure 6. Crosscutting Thick Logs with Pressure on Bottom LOGS/LIMBS WITH PRESSURE ON BOTTOM (FIGURE 5) 1. Observe all safety precautions. 2. Begin with a bottom cut. The depth of the cut should be about 1/3 of the log diameter . 3. Finish with an upper cut, down from the top. The saw cuts should meet. Figure 5. Crosscu ...

  • Stanley Black & Decker CS05 - page 17

    CS05/CS06 User Manual ◄ 17 PRUNING AND DEBRANCHING 1. Observe all safety precautions. 2. Use both hands. Keep a rm grip. 3. Be alert for kickback. Do not allow the tip of the bar to touch anything while the chain is in motion. 4. Do not cut overhead. Keep the saw below chest lev - el. The chain is too close to your face in this position. COLD ...

  • Stanley Black & Decker CS05 - page 18

    18 ► CS05/CS06 User Manual • Make sure all couplers are wiped clean before con - nection. • The hydraulic circuit control valve must be in the “OFF” position when coupling or uncoupling hydrau - lic tools. Failure to do so may result in damage to the quick couplers and cause overheating of the hy - draulic system. • Always store the too ...

  • Stanley Black & Decker CS05 - page 19

    CS05/CS06 User Manual ◄ 19 If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem. When diagnosing faults in operation of the saw , always make sure the hydraulic power source is supplying the correct hydraulic ow and pressure to the saw as listed in the table. Use a owmeter known to be ac ...

  • Stanley Black & Decker CS05 - page 20

    20 ► CS05/CS06 User Manual Capacity CS05 ..................................................................................................... 12 and 15 inch/30 and 38 cm Cut Lengths CS06 ......................................................................................... 12, 15 and 20 inch/30, 38 and 51 cm Cut Lengths Weight (w/o bar) ..... ...

  • Stanley Black & Decker CS05 - page 21

    CS05/CS06 User Manual ◄ 21 CS05/CS06 P ARTS ILLUSTRA TION ...

  • Stanley Black & Decker CS05 - page 22

    22 ► CS05/CS06 User Manual ITEM NO. P ART NO. QTY DESCRIPTION 1 00753 09622 8 CAPSCREW CAPSCREW U/W MODEL 2 07636 08202 1 NAME T AG—CS06 NAME T AG—CS05 3 28323 1 CE DECAL (CE ONL Y) 4 07652 1 REAR GEAR HSG ASSY (7–9 GPM) 07834 1 REAR GEAR HSG ASSY (4–6 GPM) 5 00289 2 DOWEL PIN 6 04041 4 BUSHING 7 00020 1 O-RING 8 07612 1 IDLER SHAFT 9 041 ...

  • Stanley Black & Decker CS05 - page 23

    CS05/CS06 User Manual ◄ 23 ITEM NO. P ART NO. QTY DESCRIPTION 71 07610 1 SPRING 72 00190 1 ROLL PIN 73 10537 1 KEEPER 74 07625 1 PLUG BUTTON 75 03786 1 GPM STICKER (7–9 GPM) 03782 1 GPM STICKER (4–6 GPM) 76 05144 1 BAR & CHAIN GUARD 77 00767 1 GREASE FITTING U/W MODEL ONL Y 00936 2 ADAPTER (NOT SHOWN) 26414 1 LOCK OUT KIT , SHIPPED INST A ...

  • Stanley Black & Decker CS05 - page 24

    24 ► CS05/06 User Manual For underwater hydraulic tools the applications are broken down into four quadrants depending on type of tool and method of operation. The types of tools are percussive and rotational, each with different characteristics allowing for dif - ferent depth operation. With percussive tools, the nitrogen accumulator PSI must co ...

  • Stanley Black & Decker CS05 - page 25

    CS05/06 User Manual ◄ 25 NOTES ...

  • Stanley Black & Decker CS05 - page 26

    Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulics.com ...

Fabricant Stanley Black & Decker Catégorie Chainsaw

Les documents que nous recevons du fabricant de l'appareilStanley Black & Decker CS05 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Stanley Black & Decker
- manuels d’utilisations CS05
- fiches produit Stanley Black & Decker
- dépliants
- ou étiquettes-énergie Stanley Black & Decker CS05
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Stanley Black & Decker CS05.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Stanley Black & Decker CS05, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Stanley Black & Decker CS05. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Stanley Black & Decker CS05.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Stanley Black & Decker CS05, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Stanley Black & Decker CS05 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Stanley Black & Decker CS05.

Le manuel d’utilisation complet Stanley Black & Decker, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Stanley Black & Decker CS05 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Stanley Black & Decker CS05, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lStanley Black & Decker CS05 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Stanley Black & Decker CS05 - qui devraient nous aider dans les premières étapes lors de l'utilisation Stanley Black & Decker CS05
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Stanley Black & Decker CS05
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Stanley Black & Decker CS05 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Stanley Black & Decker CS05?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Stanley Black & Decker CS05, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Stanley Black & Decker CS05 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)