Français dropdown-ico

Manuel d’utilisation Icom IC-A6

40 pages 0.61 mb
Télécharger

Aller à la page of 40

Summary
  • Icom IC-A6 - page 1

    INSTRUCTION MANUAL iA6 iA24 VHF AIR BAND TRANSCEIVER This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful inter- ference. IC-A24 IC-A6 ...

  • Icom IC-A6 - page 2

    i SAFETY TRAINING INFORMA TION Y our Icom radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as “Occupational Use Only”, meaning it must be used only dur- ing the course of employment by individuals aware of the haz- ards, and the ways to minimize such hazards. This radio is NOT intended fo ...

  • Icom IC-A6 - page 3

    ii FOREWORD Thank you for purchasing this Icom product. The IC-A24/A6 VHF AIR BAND TRANSCEIVER is designed and built with Icom’s state of the art technology and craftsmanship. With proper care this product should provide you with years of trouble-free operation. IMPOR T ANT READ ALL INSTRUCTIONS carefully and completely before using the transceiv ...

  • Icom IC-A6 - page 4

    iii PRECAUTION R W ARNING! NEVER hold the transceiver so that the antenna is very close to, or touching exposed parts of the body , especially the face or eyes, while transmitting. The transceiver will perform best if the microphone is 5 to 10 cm away from the lips and the transceiver is vertical. R W ARNING! NEVER operate the transceiver with a he ...

  • Icom IC-A6 - page 5

    iv SAFETY TRAINING INFORMA TION ............................................... i FOREWORD ................................................................................... ii IMPORT ANT .................................................................................... ii EXPLICIT DEFINITIONS .................................................... ...

  • Icom IC-A6 - page 6

    1 1 P ANEL DESCRIPTION ■ Panel description e rt u y i o Microphone Speaker !6 !5 !7 q w !1 !0 !2 !3 !4 WX-ALERT IC-A24 !7 WX-ALERT !7 IC-A6 ...

  • Icom IC-A6 - page 7

    2 1 q BACKLIGHT SWITCH [LIGHT] (p. 1 1) T urns the backlight for display and keypad ON or OFF . w PTT SWITCH [PTT] (p. 9) Push and hold to transmit; release to receive. •“ ” appears on the function display while transmitting. e VOLUME [VOL] (p. 9) Adjusts the audio level. r TUNING DIAL [DIAL] (pgs. 8 – 12) ➥ Rotate [DIAL] to select the de ...

  • Icom IC-A6 - page 8

    3 1 P ANEL DESCRIPTION !1 CLEAR KEY [CLR • DEL ] (pgs. 8 – 17) ➥ Push to turn to the frequency mode, when mem- ory channel, WX channel, 121.5 MHz, squelch level setting or beep tone setting is selected. ➥ Push , then push and hold [CLR • DEL ]t o delete a recall frequency data. ➥ Push to clear the entered comment of memory name while pr ...

  • Icom IC-A6 - page 9

    4 1 P ANEL DESCRIPTION 1 !7 DIGIT KEYS ➥ Input the speci fi ed digit during frequency input, memory channel selection, etc. ➥ In addition, each key has one or more secondary func- tion after pushing as follows: Push , then push [0 • BANK ] to select the mem- ory BANK number to rotate [DIAL] on the memory operation. (p. 12) Push , then push [ ...

  • Icom IC-A6 - page 10

    5 1 P ANEL DESCRIPTION ■ Function display q FUNCTION INDICA TOR (p. 2) Appears when is pushed. w TX INDICA TOR (p. 9) Appears while transmitting. e RX INDICA TOR (p. 9) Appears when receiving a signal or when the squelch opens. r DUPLEX INDICA TOR (IC-A24 only) (p. 24) ➥ “ DUP ” appears when the duplex function is activated in NA V mode. ? ...

  • Icom IC-A6 - page 11

    6 1 P ANEL DESCRIPTION 1 i T AG CHANNEL INDICA TOR (p. 17) “” appears when the memory channel is set as a T AG channel. o MEMOR Y CHANNEL INDICA TOR (pgs. 12 – 15) Shows the memory channel number . !0 MEMOR Y BANK NUMBER INDICA TOR (p. 12) Shows the selected memory bank number . !1 OVERFLOW INDICA TOR (IC-A24 only) (pgs. 18 – 22) Appears wh ...

  • Icom IC-A6 - page 12

    7 D Antenna CAUTION: DO NOT transmit without an antenna. Other- wise the transceiver may be damaged. Insert the supplied antenna into the antenna connector and screw down the antenna as shown below . D Belt clip Conveniently attaches to your belt. Attach the belt clip with the supplied screws as below . NOTE: Use the supplied screws only . D Batter ...

  • Icom IC-A6 - page 13

    8 3 BASIC OPERA TION ■ Setting a frequency ï Using keypad q Push [PWR] for 2 sec. to turn power ON, then push [CLR • DEL ] to select the frequency mode when memory CH number or WX CH number appears on the function dis- play . w Push 5 appropriate digit keys to input the frequency . • Push [1]* as the 1st digit. • When a wrong digit is inpu ...

  • Icom IC-A6 - page 14

    9 3 BASIC OPERA TION ■ Receiving q Push [PWR] to turn the power ON. w Push [SQL • WX-ALERT ], then rotate [DIAL] counterclock- wise to select the squelch level 0. e Rotate [VOL] to adjust the audio level. r Push [SQL • WX-ALERT ], then rotate [DIAL] clockwise until the noise is muted. •“ ” indicator disappears. t Set the desired frequen ...

  • Icom IC-A6 - page 15

    10 3 BASIC OPERA TION ■ Low battery indicator Low battery indicator appears when the battery power has de- creased to a speci fi ed level. The attached battery pack requires recharging. ■ Recall function The recall function stores the last 10 frequencies used. The function stores frequencies when the frequency is pro- grammed and transmitted o ...

  • Icom IC-A6 - page 16

    11 3 BASIC OPERA TION ■ Setting weather alert function An NOAA broadcast station transmits a weather alert tone be- fore any important weather announcements. When the weather alert function is turned ON, the transceiver detects the alert, and sounds a beep tone until the transceiver is op- erated. The previously selected (used) weather channel is ...

  • Icom IC-A6 - page 17

    12 4 MEMOR Y OPERA TION ■ Memory channel selection The transceiver has 200 memory channels for storage of often-used frequencies along with 6-character notes. q Push [MR • MW ] to select memory mode. • Memory BANK number and memory CH. number appears. Using [DIAL]: w Push [0 • BANK ], then rotate [DIAL] to select the desired memory BANK num ...

  • Icom IC-A6 - page 18

    13 4 MEMORY OPERA TION ■ Programming a memory channel The transceiver has 200 (20 CH. × 10 BANK) memory chan- nels for storage of often-used frequencies. q Push [CLR • DEL ] to select the frequency mode, if neces- sary . w Select the desired frequency . • Push , then push [ENT • WX ] to select a weather channel.* • Set the desired freque ...

  • Icom IC-A6 - page 19

    14 4 MEMORY OPERA TION ■ Memory names ï Programming memory names The memory channel can display a 6-character names in- stead of the programmed frequency . q Rotate [DIAL] to select the desired frequency in the fre- quency mode. w Push , then push [MR • MW ] to program the contents into the selected memory channel. e Rotate [DIAL] to select th ...

  • Icom IC-A6 - page 20

    15 4 MEMORY OPERA TION Push Push Push Push Push Push Push Push Push Push • EXAMPLE: Programming 125.000 MHz into memory BANK 1/ memory channel 17 with “ AIR-23 ” as a comment. NOTE: Push [0 • BANK ], then rotate [DIAL] to select the BANK number , if desired. Push [CLR • DEL ] to continue memory name programming. ...

  • Icom IC-A6 - page 21

    16 5 SCAN OPERA TION ■ Scan types The U.S.A. version has 3 scan types to suit your needs. The non-U.S.A. versions have 2 scan types. ■ COM band scan q Push [CLR • DEL] to select the frequency mode. w Push [SQL • WX-ALERT ] to set the squelch level to the point where noise is just muted. e Push , then push [ANL • SCAN ] to start the scan. ...

  • Icom IC-A6 - page 22

    17 5 SCAN OPERA TION ■ W eather channel scan (U.S.A. version only) q Push , then push [ENT • WX ] to select a weather chan- nel. w Set squelch to the point where noise is just muted. e Push , then push [ANL • SCAN ] to start the scan. • When a signal is received, the scan pauses until it disappears. • T o change the scanning direction, ro ...

  • Icom IC-A6 - page 23

    18 6 VOR NA VIGA TION (IC-A24 ONL Y) ■ VOR indicators 214 34 FROM COM BAND (118.00 136.975 MHz) NAV BAND (108.00 117.975 MHz) DVOR MODE Function display of the IC-A24 General VOR equipment To-from flag indicator CDI MODE Course indicator Course indicator Course deviation needles Overflow indicator Push [F] then [4 CDI ]. Push [F] then [1 DVOR ]. ...

  • Icom IC-A6 - page 24

    19 6 VOR NA VIGA TION (IC-A24 ONL Y) ■ VOR functions D T o select the CDI mode T o show the deviation between your fl ying course and the de- sired course, push , then push [4 • CDI ] to select the CDI mode. D T o select the DVOR mode When entering the NA V band, 108.000 – 1 17.975 MHz, the IC-A24 selects the DVOR mode automatically . T o sh ...

  • Icom IC-A6 - page 25

    20 6 VOR NA VIGA TION (IC-A24 ONL Y) ■ Flying to a VOR station The IC-A24 shows the deviation from a VOR station. q Select a VOR station on your aeronautical chart and push the keypad or rotate [DIAL] to set the frequency of the sta- tion. • The course indicator indicates where you are located on a radial from the VOR station. • The course in ...

  • Icom IC-A6 - page 26

    21 6 VOR NA VIGA TION (IC-A24 ONL Y) VOR station 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250 260 270 280 290 300 310 320 330 340 350 N Magnetic north Desired course Aircraft heading 40 123.65 VORTAC SEATTLE 116.8 Ch 115 SEA THE AIRCRAFT IS ON COURSE VOR station 0 10 20 30 40 50 60 70 80 90 100 110 12 ...

  • Icom IC-A6 - page 27

    22 6 VOR NA VIGA TION (IC-A24 ONL Y) ■ Entering a desired course The IC-A24 shows not only the deviation from the VOR sta- tion but the deviation from the desired course. q Push the keypad or rotate [DIAL] to set the frequency for the desired VOR station. • Push , then push [2 • TO ] or [3 • FROM ] to change the to-from fl ag. w Push , the ...

  • Icom IC-A6 - page 28

    23 6 VOR NA VIGA TION (IC-A24 ONL Y) EXAMPLE: Entering the desired course bearing 65 ° to a VOR station. VOR station 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250 260 270 280 290 300 310 320 330 340 350 N Magnetic north VOR station 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 2 ...

  • Icom IC-A6 - page 29

    24 6 VOR NA VIGA TION (IC-A24 ONL Y) ■ Duplex operation (U.S.A. version only) The duplex function allows you to call a fl ight service station while receiving a VOR station. The duplex function requires frequency programming for the flight service station in ad- vance. D Programming a duplex frequency q Push [CLR • DEL ] to select the frequenc ...

  • Icom IC-A6 - page 30

    25 7 BA TTER Y P ACKS ■ Battery charging Prior to using the transceiver for the first time, the battery pack must be fully charged for optimum life and operation. CAUTION: T o avoid damage to the transceiver , turn the power OFF while charging. • Recommended temperature range for charging: +10 ° C to +40 ° C (+50 ° F to +104 ° F) - The Li-I ...

  • Icom IC-A6 - page 31

    26 7 BA TTERY P ACKS D Regular charging q Attach the battery pack to the transceiver . w Be sure to turn the transceiver power OFF . e Connect the W all charger or optional cable (CP-20) as shown below . r Charging the battery pack approx. 8 hours, depending on the remaining power condition. DO NOT charge BP-210N more than 12 hours. Otherwise, BP-2 ...

  • Icom IC-A6 - page 32

    27 7 BA TTERY P ACKS ■ Optional battery chargers D Rapid charging with the BC-1 19N+AD-101 The optional BC-1 19N provides rapid charging of battery packs. The following are additionally required. • AD-101 charger adapter. • An AC adapter (may be supplied with BC-1 19N depending on ver- sions). NOTE : Attach the spacer (Spacer B / C ) to the a ...

  • Icom IC-A6 - page 33

    28 8 CLONING Cloning allows you to quickly and easily transfer the programmed data from one transceiver to another transceiver , or , data from PC to a transceiver using the optional CS-A24 cloning software. D T ransceiver to transceiver cloning q Connect the OPC-474 CLONING CABLE with adapter plugs to [SP/MIC] jack of the master and slave transcei ...

  • Icom IC-A6 - page 34

    29 9 TROUBLESHOOTING If your transceiver seems to be malfunctioning, please check the following points before sending it to a service center . PROBLEM POSSIBLE CAUSE SOLUTION REF . No power comes on. • The battery is exhausted. • Recharge the battery pack. pgs. 7, • Bad connection for the battery pack. • Check the connection to the transcei ...

  • Icom IC-A6 - page 35

    30 10 SPECIFICA TIONS D General • Frequency coverage (MHz): TX 1 18.000 to 136.975 RX 108.000 to 136.975* 1 WX 161.650 to 163.275* 2 * 1 : IC-A24 only , IC-A6; 1 18.000 to 136.975 MHz * 2 : U.S.A. version only . • Mode : 6K00A3E 16K0G3E (161.65 to 163.275 MHz) • Channel spacing : 2 5 k H z • Number of memory channels : 200 (20 CH. × 10 BAN ...

  • Icom IC-A6 - page 36

    31 11 OPTIONS D BA TTERY CASE AND P ACKS • BP-208N BA TTERY CASE Battery case for 6 × AA (R6) Alkaline cells. • BP-209N Ni-Cd BA TTERY P ACK 7.2 V/1 100 mAh Ni-Cd battery pack. • BP-210N Ni-MH BA TTERY P ACK 7.2 V/1650 mAh Ni-MH battery pack. • BP-21 1N Li-Ion BA TTERY P ACK 7.4 V/1800 mAh Li-Ion battery pack. D CHARGERS • BC-1 10AR/DR W ...

  • Icom IC-A6 - page 37

    OPERA TION GUIDE iA24/A6 VOR NA VIGA TION (p. 20) VOR NA VIGA TION (p. 22) Flying to a VOR station Entering a desired course. q w e q w Push keypad or rotate [DIAL] to set the frequency for the de- sired VOR station. Push , then push [2 TO ] or [3 FROM ] to change the to- from flag. Push , then push [4 CDI ] to select CDI mode. ' Ω ' or ...

  • Icom IC-A6 - page 38

    33 12 QUICK REFERENCE T ransferring memory contents MEMOR Y OPERA TION (p. 13) MEMOR Y OPERA TION (p. 12) q w e r t Push [CLR DEL ] to select the fre- quency mode or push , then push [ENT WX ] to select WX CH* mode. Select the desired frequency or WX CH.* Push , then push [MR MW ] to enter memory programming mode. “ M ” , BANK and memory number ...

  • Icom IC-A6 - page 39

    34 13 OPTIONAL HEADSET CONNECTION D OPC-499 ( HEADSET ADAPTER) connection When using a headset, such as those from the David Clark Co. via the OPC-499 HEADSET ADAPTOR adapter , the transceiver out- puts your transmitted voice to the headset for monitoring. See “ ■ Side tone function “ (p. 1 1) when setting the side tone level. PTT OPC-499 IC- ...

  • Icom IC-A6 - page 40

    1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan A-6403D-1EX Printed in Japan © 2004 Icom Inc. ...

Fabricant Icom Catégorie Marine Radio

Les documents que nous recevons du fabricant de l'appareilIcom IC-A6 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Icom
- manuels d’utilisations IC-A6
- fiches produit Icom
- dépliants
- ou étiquettes-énergie Icom IC-A6
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Icom IC-A6.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Icom IC-A6, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Icom IC-A6. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Icom IC-A6.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Icom IC-A6, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Icom IC-A6 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Icom IC-A6.

Le manuel d’utilisation complet Icom, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Icom IC-A6 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Icom IC-A6, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lIcom IC-A6 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Icom IC-A6 - qui devraient nous aider dans les premières étapes lors de l'utilisation Icom IC-A6
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Icom IC-A6
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Icom IC-A6 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Icom IC-A6?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Icom IC-A6, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Icom IC-A6 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)