Français dropdown-ico

Manuel d’utilisation Echo CS-330T

32 pages 1.3 mb
Télécharger

Aller à la page of 32

Summary
  • Echo CS-330T - page 1

    X7503242502 X750009912 1 1/09 W ARNING Read rules for safe operation and instructions carefully . ECHO provides an Instruc- tion Manual and a Safety Manual. Both must be read and understood for proper and safe operation. Chain Saw Instruction Manual MODELS : CS-330T CS-360T ...

  • Echo CS-330T - page 2

    2 R u l e s f o R s a f e o p e R a t i o n A. Kickback Safety Precautions for Chain Saw Users Copyright© 2010 By Echo, Incorporated All Rights Reserved. B. Other Safety Precautions 1. Do not operate a chain saw with one hand! Serious injury to the operator , helpers, bystanders, or any com - bination of the se persons may result from one-handed o ...

  • Echo CS-330T - page 3

    3 14. Keep the handles dry , clean, and free of oil or fuel mixture. 15. Operate the chain saw only in well-ventilated areas. 16. Do not operate a chain saw in a tree unless you have been specically trained to do so. 17. All chain saw service, other than the items listed in the Instruction Manual maintenance instructions, should be performed by ...

  • Echo CS-330T - page 4

    4 i n t e R n a t i o n a l s y m b o l s C o n t e n t s Page Rules for Safe Operation .................................................................................................. 2 T echnical Data .................................................................................................................. 5 Emission Data .............. ...

  • Echo CS-330T - page 5

    5 t e C h n i C a l D a t a * T echnical data subject to change without notice. Model CS-330T CS-360T Dimension L x W x H mm inch Weight Power head, dry kg Type Displacement 32.6 (1.989 cu.in.) 36.3 (2.215 cu.in.) Carburetor Ignition Spark Plug Starter Power transmission Mixture ratio Tank Capacity ml Oil Bar and chain Tank Capacity ml Lubrication ...

  • Echo CS-330T - page 6

    6 D e s C R i p t i o n The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restric- tions, guide bar and saw chain installation and other assembly may be necessary . After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the conte ...

  • Echo CS-330T - page 7

    7 1. Hand guard (Chain brake actuating lever) 2. Ignition/Choke Lever 3. Throttle control trigger 4. Throttle control lockout 5. Air cleaner cover 6. Pull starter 7. Front handle 8. Oil tank cap 9. Fuel tank cap 10. Saw chain 1 1. Guide bar n o m e n C l a t u R e o f p a R t s Cs-330t , Cs-360t 10 11 12 13 14 12. Sprocket guard 13. Catalytic muf? ...

  • Echo CS-330T - page 8

    8 KICK GUARD® TO BAR INSTRUCTIONS For saws with Kick Guard ® P/N 2894901 and symmetri- cal or asymmetrical low-kick type guide bars. 1. Install bolt (A) in rear hole (B) of Kick Guard ® and through front hole (C) in guide bar . 2. IMPORT ANT : Dimple in Kick Guard ® (D) must engage recess in guide bar (E). 3. T ighten nut (F) and bolt (A) until ...

  • Echo CS-330T - page 9

    9 p o 7. T urn saw over and check brake band (O) for cor- rect position around clutch drum (P). If brake band is not in place around drum, remove clutch cover , make sure brake is released, and reinstall. DANGER Never operate saw if chain brake does not function properly , otherwise saw damage and serious personal injury could result. See “T esti ...

  • Echo CS-330T - page 10

    10 NOTICE: Use of unmixed, improperly mixed, or fuel older than 90 days, (stale fuel), may cause hard starting, poor performance, or severe engine damage and void the product warranty . Read and follow instructions in the Storage section of this manual. f u e l s t a t e m e n t W ARNING Alternative fuels, such as E-15 (15% ethanol), E-85 (85% etha ...

  • Echo CS-330T - page 11

    11 o p e R a t i o n IMPORT ANT This saw features a combination ignition/choke switch that automatically sets the throttle speed to fast idle for quick starting. Do not squeeze trigger during cold starts until after unit has started, or fast idle and choke set- tings will be released, and engine may not start. CHAIN LUBRICANT Proper lubrication of ...

  • Echo CS-330T - page 12

    12 5. Lay unit on a at, clear area and keep bar and chain clear of all obstacles. Hold top handle with one hand, and depress throttle trigger lockout (C), but do not depress throttle trigger (D). 6. Pull starter handle (F) several times until engine starts, or rst starting sound is heard. (7 pulls maximum) 7. Move ignition/choke lever back to ...

  • Echo CS-330T - page 13

    13 A A E D D STOPPING 1. Release throttle trigger (D) and move lever (A) rearward to STOP ( O ) position. 2. Move chain brake lever (E) fully forward to lock chain brake. NOTE If engine does not stop, move ignition/choke lever forward to choke position ( ) to stop engine. Return the unit to your authorized ECHO dealer to check and repair stop switc ...

  • Echo CS-330T - page 14

    14 W ARNING Read the ECHO “CHAIN SA W SAFETY MANUAL” included with your chain saw for additional cutting and safety instruc- tions. Failure to obey all instructions may result in serious or fatal injuries. In all circumstances the operation of the chain saw is a one-man job. It is difcult at times to take care for your own safety , so don’ ...

  • Echo CS-330T - page 15

    15 W ARNING A falling tree can seriously damage anything it may hit - a car , a house, a fence, a power line, or another tree. There are ways to make a tree fall where you want it, so rst decide where that is! Before cutting, clear the area around the tree. Y ou will need good footing while working and you should be able to work the saw without ...

  • Echo CS-330T - page 16

    16 Don’t cut with the saw overhead or the bar in a vertical po- sition. If the saw should kick back you may not have good enough control to prevent possible injury . Bucking is the sawing of a log or fallen tree into smaller pieces. There are a few basic rules which apply to all bucking operations. Keep both hands on the handles at all times. Sup ...

  • Echo CS-330T - page 17

    17 m a i n t e n a n C e a n D C a R e W ARNING Moving parts can amputate ngers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a com- plete stop before removing obstructions, clearing debris, or servicing unit. Allow u ...

  • Echo CS-330T - page 18

    18 AIR FIL TER 1. Close choke (Cold Start Position [ ]). This prevents dirt from entering the carburetor throat when the air lter is removed. Brush accumulated dirt from air cleaner area. 2. Remove air lter cover . Brush dirt from inside cover . 3. Remove air lter and lightly brush debris from lter . Replace lter if it is damaged, fu ...

  • Echo CS-330T - page 19

    19 SP ARK PLUG • Check periodically . IMPORT ANT Use only NGK BPM-8Y spark plug (BPMR-8Y in Canada) otherwise severe engine damage may occur . 1. Remove air cleaner cover . 2. Remove spark plug lead and spark plug. 3. Gap = 0.65 mm (0.026 in) 4. Replace if electrode is worn, or if the insulator is fouled by oil or other deposits 5. T orque = 150 ...

  • Echo CS-330T - page 20

    20 MUFFLER SP ARK ARREST OR IMPORT ANT Carbon deposits in mufer will cause a drop in engine output and overheating. Spark arrestor screen must be checked periodically . 1. Remove air lter cover and remove spark plug lead. 2. Remove two guide bar nuts and remove sprocket guard. 3. Remove three mufer cover screws and remove mufer cover . ...

  • Echo CS-330T - page 21

    21 6. Use a wood or plastic scraping tool to clean deposits from cylinder exhaust ports (G). IMPORT ANT If mufer mounting studs loosened during mufer nut removal, tighten studs using two nuts (H) tightened together on end of stud. T urn outer nut clockwise, and tighten stud to 70 kgf • cm (7 N-m, 60 in • lbf). Do not exceed specication ...

  • Echo CS-330T - page 22

    22 CARBURETOR ADjUSTMENT Engine Break-In New engines must be operated a minimum duration of two tanks of fuel break-in before carburetor adjustments can be made. Dur- ing the break-in period your engine performance will increase and exhaust emissions will stabilize. Idle speed can be adjusted as required. High Altitude Operation This engine has bee ...

  • Echo CS-330T - page 23

    23 HIGH AL TITUDE ADjUSTMENT 1. Start engine and run for several minutes to reach operating temperature. 2. Stop engine. 3. Start engine and turn the HI speed needle (A) lean (CW) until the engine runs between 13,500 and 14,500 RPM. Then turn the LO speed needle lean (B) (CW) until the engine does not hesitate when accelerated. DO NOT REMOVE LIMITE ...

  • Echo CS-330T - page 24

    24 W ARNING Use of replacement saw chain and/or guide bar other than that specied, or operation without the “tip guard” in place, may cause severe kickback resulting in serious injury . Only use saw chain designated as, “LOW -KICKBACK,” that meets the ANSI B175.1-2000 Standard when tested on the representative sample of chain saws below ...

  • Echo CS-330T - page 25

    25 3/8A (SPROCKET) 30° 80° 60° 0.64 mm (0.025 in.) Parallel • Properly led cutters are shown below . (T op plate angle) (Side plate angle) (T op plate cutting angle) (Depth gauge) • When setting of the chain is nished, soak it in oil and wash away lings completely before using. • When chain has been led on the bar , supply suf? ...

  • Echo CS-330T - page 26

    26 T R A H C G N I T O O H S E L B U O R T M E L B O R P E N I G N E m e l b o r Pk c e h Cs u t a t Se s u a Cy d e m e R e n i g n E - s k n a r c / d r a h s t r a t s t ' n s e o d t r a t s r o t e r u b r a c t a l e u Fr o t e r u b r a c t a l e u f o Nd e g g o l c r e n i a r t s l e u F d e g g o l c e n i l l e u F r o t e r u b r ...

  • Echo CS-330T - page 27

    27 s t o R a g e a f t e R u s e • Inspect and adjust every part of the chain saw . - Completely clean every part, and repair , if necessary . - Apply thin coating of oil on metal parts to prevent corrosion. • Drain fuel tank, pull starter slowly a few times to drain fuel from carburetor . • Pour a small amount of clean two-stroke oil into sp ...

  • Echo CS-330T - page 28

    28 TESTING THE BRAKE • Start the engine on a solid level surface and run at a fast idle until warm. • Hold the saw rmly by the handles and accelerate the en - gine to a fast idle. • Slowly operate the chain brake lever while holding the saw rmly on the ground. When the brake lever trips, the chain should stop. Immediately release the th ...

  • Echo CS-330T - page 29

    29 ECHO LIMITED W ARRANTY ST A TEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010 ECHO'S RESPONSIBILITY ECHO Incorporated ’s Limited Warranty , pro vides to the original purcha ser that this ECHO pr oduct is free from defects in material and w orkmanship . Under normal use and maintenance from date of purchase, ECHO agrees to rep ...

  • Echo CS-330T - page 30

    30 PURCHASED REP AIR P ARTS, SHORT BLOCKS AND ACCESSORIES   ...

  • Echo CS-330T - page 31

    31 ECHO INCORPORA TED EMISSION CONTROL W ARRANTY ST A TEMENT FOR ECHO AND SHINDAIW A BRANDS The Environmental Protection Agency (EP A) and the California Air Resources Board (C.A.R.B.) and ECHO Incorporated (ECHO Inc.) are pleased to explain the emission control system warranty on your 2010 and later equipment/small off-road engine (SORE). New equi ...

  • Echo CS-330T - page 32

    CONSUMER PRODUCT SUPPORT 1-800-673-1558 8:30 - 4:30 Mon - Fri C.S.T . ECHO, INCORPORA TED 400 O A k w O O D R O A D L A k E Z u R i c h , iL 60047-1564 www .echo-usa.com DEALER? Call 1-800-432-ECHO 1-800-432-3246 or www .echo-usa.com s e R v i C i n g i n f o R m a t i o n p a R t s / s e R i a l n u m b e R Genuine ECHO Parts and ECHO REPOWER™ P ...

Fabricant Echo Catégorie Chainsaw

Les documents que nous recevons du fabricant de l'appareilEcho CS-330T peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Echo
- manuels d’utilisations CS-330T
- fiches produit Echo
- dépliants
- ou étiquettes-énergie Echo CS-330T
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Echo CS-330T.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Echo CS-330T, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Echo CS-330T. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Echo CS-330T.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Echo CS-330T, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Echo CS-330T par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Echo CS-330T.

Le manuel d’utilisation complet Echo, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Echo CS-330T - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Echo CS-330T, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lEcho CS-330T qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Echo CS-330T - qui devraient nous aider dans les premières étapes lors de l'utilisation Echo CS-330T
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Echo CS-330T
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Echo CS-330T dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Echo CS-330T?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Echo CS-330T, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Echo CS-330T il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)