-
JBL CONTROL NOW - page 1
JBL CONTROL NOW ™ JBL CONTROL NOW ™ AW JBL ® CONTROL ® SERIES OWNER’S GUIDE ® JBLP2605_CN_CNAW_PM-OM 4/23/08 12:57 PM Page 1 ...
-
JBL CONTROL NOW - page 2
2 T ABLE OF CONTENTS UNP ACKING THE SPEAKERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 W ALL SURFACE-MOUNTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 W ALL CORNER-MOUNTING . . . . . . . . . . . . . . . . . . . . ...
-
JBL CONTROL NOW - page 3
3 PLACEMENT JBL Control NOW speakers are perhaps the most flexible and versatile loud- speakers ever developed. There are numerous mounting options. The JBL Control NOW speaker can be wall-mounted or corner -mounted, sit on a shelf or be used with floor stands. T wo, three or four speakers can be joined together to create loudspeaker solutions for ...
-
JBL CONTROL NOW - page 4
4 W ALL SURF ACE-MOUNTING When deciding upon a location for the JBL Control NOW speaker , take care NOT to install the mounting bracket closer than 3" (horizontal) and 8-1/2" (vertical) to the ceiling. Any closer than the minimum measurements will not allow the room needed to position and slide the JBL Control NOW speaker into the mountin ...
-
JBL CONTROL NOW - page 5
5 4. The mounting bracket is designed to trap the flange of the JBL Control NOW speaker by securing the mounting-bracket cap with two screws through the bottom of the mounting bracket. Rest the JBL Control NOW speaker’ s rear flange in the mounting bracket, as shown. This will support the weight of the speaker . Slide the mounting-bracket cap ove ...
-
JBL CONTROL NOW - page 6
6 W ALL CORNER-MOUNTING CA UTION The customer is responsible for proper selection and use of mounting hardware (available through hardware stores), to properly and safely wall-mount the speakers. The JBL Control NOW speaker was designed to be easily installed. However , if you are unable to clearly and fully understand and follow the instructions i ...
-
JBL CONTROL NOW - page 7
7 4. The mounting bracket is designed to trap the flange of the JBL Control NOW speaker by securing the mounting-bracket cap with two screws through the bottom of the mounting bracket. Rest the JBL Control NOW speaker’ s rear flange in the mounting bracket, as shown. This will support the weight of the speaker . Now slide the mounting-bracket cap ...
-
JBL CONTROL NOW - page 8
8 3. Connect the wires to the JBL Control NOW speaker . IMPORT ANT : Make sure all equipment is turned off before making any connections. For speaker connections, use a high-quality speaker wire with polarity coding. The side of the wire with a ridge or other coding is usually considered positive polarity (i.e., +). NOTE: If desired, consult your l ...
-
JBL CONTROL NOW - page 9
9 4. The mounting bracket is designed to trap the flange of the JBL Control NOW speaker by securing the mounting-bracket cap with two screws through the side of the mounting bracket. Rest the JBL Control NOW speaker’ s flange in the mounting bracket, as shown. This will support the weight of the speaker . Now slide the mounting-bracket cap over t ...
-
JBL CONTROL NOW - page 10
10 HALF-ROUND W ALL-MOUNTING (HORIZONT AL OR VERTICAL) NOTE: Decide whether you will connect the speakers as a single channel or two separate channels, and follow the appropriate instructions on the following pages. CONNECT AS A SINGLE CHANNEL CA UTION The customer is responsible for proper selection and use of mounting hardware (available through ...
-
JBL CONTROL NOW - page 11
11 5. The mounting bracket is designed to trap the flange of the JBL Control NOW speaker by securing the mounting-bracket cap with two screws through the bottom of the mounting bracket. Run the loose end of the multiunit wiring adapter through the rear cable-management hole in the mounting bracket, and rest the JBL Control NOW speaker’ s rear fla ...
-
JBL CONTROL NOW - page 12
12 CONNECT AS TWO CHANNELS CA UTION The customer is responsible for proper selection and use of mounting hardware (available through hardware stores), to properly and safely wall-mount the speakers. The JBL Control NOW speaker was designed to be easily installed. However , if you are unable to clearly and fully understand and follow the instruction ...
-
JBL CONTROL NOW - page 13
13 4. The mounting bracket is designed to trap the flange of the JBL Control NOW speaker by securing the mounting bracket cap with two screws through the bottom of the mounting bracket. This will support the weight of the speaker . Now slide the mounting-bracket cap over the assembly . Secure the mounting- bracket cap by inserting two #10-32 x 2&qu ...
-
JBL CONTROL NOW - page 14
3/4-ROUND W ALL-MOUNTING CA UTION The customer is responsible for proper selection and use of mounting hardware (available through hardware stores), to properly and safely wall-mount the speakers. The JBL Control NOW speaker was designed to be easily installed. However , if you are unable to clearly and fully understand and follow the instructions ...
-
JBL CONTROL NOW - page 15
15 4. Connect the small end of the multiunit wiring adapter to the rear of speaker 1, as shown. 5. The mounting bracket is designed to trap the flange of the JBL Control NOW speaker by securing the mounting-bracket cap with two screws through the bottom of the mounting bracket. Run the loose end of the multiunit wiring adapter through the rear cabl ...
-
JBL CONTROL NOW - page 16
16 9. Place the large end of the multiunit wiring adapter that is already installed in speaker 2 into speaker 3 by sliding a multiunit wiring adapter into the rear of it at a slight angle and rotate clockwise. 10. Connect the terminal assembly to the back of the second multiunit wiring adapter . It will snap securely into place. The other end of th ...
-
JBL CONTROL NOW - page 17
17 ST AND-MOUNTING IMPORT ANT SAFETY NOTE: CA UTION The supplied floor stand adapters facilitate installation with a variety of general- purpose floor stands available from many manufacturers. Since different stands will have different weight capacities and stability characteristics, it is the customer’ s responsibility to check with the stand ma ...
-
JBL CONTROL NOW - page 18
CA UTION The JBL Control NOW PMB Pole-Mount Bracket facilitates installation of the JBL Control NOW and JBL Control NOW A W loudspeakers with a variety of general-purpose ceiling-fan-pole assemblies available from many manufacturers. Since different fan-pole assemblies will have different weight capacities, pole diameters and mounting systems, it i ...
-
JBL CONTROL NOW - page 19
19 2A. Slide the pole-mount bracket up onto the drop tube, aligning the pinholes on the bracket with those on the drop tube. (FOR SMALLER-DIAMETER DROP TUBES) 2B. When using a smaller drop tube, use the pole bushing when running the wiring down through pole-mount-bracket cap. This will help to eliminate pole wobble. 3. Slide the clevis pin through ...
-
JBL CONTROL NOW - page 20
SPEAKER WIRING 1. Use the cable assembly provided to wire the units for a single channel. Single-channel-wiring diagram. 2. Use the multiunit wiring adapters to wire the units for two channels. NOTE: There are two options for 2-channel wiring: 2A. Even sound distribution – Use this connection for even sound distribution through both channels. Thi ...
-
JBL CONTROL NOW - page 21
21 SINGLE-CHANNEL WIRING 1. Use the cable assembly provided. Run the cable assembly down the drop tube; run the four sets of paired wires out through the wire access holes, as shown. NOTE: This procedure is applicable for both large- and small-diameter drop tubes. A large-diameter drop tube is shown here. Single-channel wiring. NOTE: This procedure ...
-
JBL CONTROL NOW - page 22
2-CHANNEL WIRING FOR EVEN SOUND DISTRIBUTION 1. Use the even sound distribution connection for even sound distribution through both channels. Run the sets of paired wires out two wire access holes through the pole-mount bracket, as shown. NOTE: This procedure is applicable for both large- and small-diameter drop tubes. A large-diameter drop tube is ...
-
JBL CONTROL NOW - page 23
23 7. Connect the wires to the terminal assembly and place the speaker on the pole-mount bracket. Repeat this process with speaker D. Return to the installation procedures and continue. IMPORT ANT : Make sure all equipment is turned off before making any connections. For speaker connections, use a high-quality speaker wire with polarity coding. The ...
-
JBL CONTROL NOW - page 24
2-CHANNEL STEREO WIRING 1. Use the stereo sound-distribution connection for a smaller home theater/stereo environment. Run the sets of paired wires out two opposite wire access holes through the pole-mount bracket, as shown. NOTE: This procedure is applicable for both large- and small-diameter drop tubes. A large-diameter drop tube is shown here. 2 ...
-
JBL CONTROL NOW - page 25
25 7. Connect the wires to the terminal assembly and place the speaker on the pole-mount bracket. Repeat this process with speaker A. Return to the installation procedures and continue. IMPORT ANT : Make sure all equipment is turned off before making any connections. For speaker connections, use a high-quality speaker wire with polarity coding. The ...
-
JBL CONTROL NOW - page 26
26 #10-32 x 2" Screws (4) Drop Tube Pole- Mount-Bracket Cap Pole- Mount Bracket Onl y t wo speakers shown here for clarity. Place the pole-mount-bracket cover over the bottom visible mounting bracket by snapping it into place. Pole- Mount Bracket Cap Drop Tube SPEAKER MOUNTING After carefully placing all four speakers in the mounting bracket, ...
-
JBL CONTROL NOW - page 27
27 MAINTENANCE AND SERVICE The enclosure may be cleaned using a soft cloth to remove fingerprints or to wipe off dust. All wiring connections should be inspected and cleaned or remade periodically . The frequency of maintenance depends on the metals involved in the connections, atmospheric conditions and other factors, but once per year is the mini ...
-
JBL CONTROL NOW - page 28
28 JBL CONTROL NOW ™ JBL CONTROL NOW ™ AW Frequency Response (–6dB) 80Hz – 30kHz Max. Recommended Amplifier Power* 150W Power Handling (Continuous/Peak) 50W/300W Sensitivity (2.83V/1m) 90dB Nominal Impedance 8 Ohms Crossover Frequencies 2000Hz – 18dB/octave; woofer 36dB/octave tweeter; Low-Frequency T ransducers Dual 4" (100mm) PolyP ...
-
JBL CONTROL NOW - page 29
Features, specifications and appearance are subject to change without notice. JBL and Bi-Radial are trademarks of Harman International Industries, Incorporated, registered in the United States and/or other countries. JBL Control NOW , PolyPlas and Pro Sound Comes Home are trademarks of Harman International Industries, Incorporated. ® PRO SOUND COM ...
Avez-vous une question à propos de JBL CONTROL NOW?
Utiliser le formulaire ci-dessous
Si vous n’avez pas résolu votre problème avec JBL CONTROL NOW, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec JBL CONTROL NOW il est probable qu’il a envie de partager la façon de le résoudre.