Français dropdown-ico

Manuel d’utilisation Fisher & Paykel DD60S 7

23 pages 7.28 mb
Télécharger

Aller à la page of 23

Summary
  • Fisher & Paykel DD60S 7 - page 1

    NZ A U GB IE 590200C 12. 11 DD60S 7 & DD60ST 7 models INST ALLA TION INSTRUCTIONS DishDr aw er TM dish w asher ...

  • Fisher & Paykel DD60S 7 - page 2

    2 FOLL OW THE INS T ALLA TION SE QUENCE RELEV ANT T O Y OUR MODEL 1 DD60SHI7 Classic PRODUCT & CABINETRY DIMENSIONS (ST ANDARD HEIGHT) PRODUCT & CABINETRY DIMENSIONS (ST ANDARD HEIGHT) PRODUCT & CABINETRY DIMENSIONS (ST ANDARD HEIGHT) PRODUCT & CABINETRY DIMENSIONS (T ALL HEIGHT) PRODUCT & CABINETRY DIMENSIONS (T ALL HEIGHT) PRO ...

  • Fisher & Paykel DD60S 7 - page 3

    3 SAFETY AND W ARNINGS - ALL MODELS ADDITIONAL SAFETY AND W ARNINGS - INTEGRA TED MODELS ONL Y 2a 2b W ARNING! Electrical shock hazard Before installing the dish washer , remov e the house fuse or open the circuit breaker . This appliance must be earthed. In the event of a malfunction or breakdown, earthing will reduce the risk of electric shock by ...

  • Fisher & Paykel DD60S 7 - page 4

    4 P ARTS SUPPLIED - ALL MODELS 3a If the Drain hose supplied is not long enough to reach your services, y ou must use a Drain Hose Extension Kit P/N 525798 which will extend the drain hose by 3.6m. The kit is available from the nearest F isher & Paykel Authorised Service Centre or through our loc al website listed at the end of this document. C ...

  • Fisher & Paykel DD60S 7 - page 5

    5 ADDITIONAL P ARTS SUPPLIED WITH INTE GRA TED MODELS 3b External V enting kit (1) supplied with Integrated models with remote (NZ A U) only Panel mounting screws (6) Panel bracket (1) (attached to product ) Integrated rectangular badge (1) (Satin chrome supplied) supplied with Integrated models with badge (GB IE) only ...

  • Fisher & Paykel DD60S 7 - page 6

    6 4 PRODUCT DIMENSIONS A H I J K Side Plan G F B C D E Product dimensions (mm) ST ANDARD HEIGHT MODELS T ALL HEIGHT MODELS Classic Designer Integrated Remote control Integrated Badge control Classic Designer Integrated Remote control 456 mm cavity Integrated Badge control 456 mm cavity Integrated Remote control 480 mm cavity Integrated Badge contro ...

  • Fisher & Paykel DD60S 7 - page 7

    7 5 CABINETR Y DIMENSIONS min. 412mm 456mm 480mm LL L dishwasher dish washer dishwasher Standard height models T all height Classic models T all height Integrated models Compact Ove n Single Ove n T all height Designer models Plan Side L N M Cavity height options allow you to match dishw asher with your c abinetry or companion products Minimum clea ...

  • Fisher & Paykel DD60S 7 - page 8

    8 The following calculations assume the top of the panel is aligned with the top of the adjacent cabinetry: WID TH OF THE P ANEL Measure A ( the width between adjacent door/drawer fr onts) and write it in the  rst box below , then complete the equation. HEIGHT OF THE P ANEL Measure B and write it in the  rst box below , then complete the equa ...

  • Fisher & Paykel DD60S 7 - page 9

    9 The following calculations assume the top of the panel is aligned with the top of the adjacent cabinetry: WID TH OF THE P ANEL Measure A ( the width between adjacent door/drawer fr onts) and write it in the  rst box below , then complete the equation. HEIGHT OF THE P ANEL Measure B and write it in the  rst box below , then complete the equa ...

  • Fisher & Paykel DD60S 7 - page 10

    10 7a CA VITY PREP ARA TION W ater Connection Recommended COLD (Maximum 60°C ). ¾ “ BSP (GB20) to suit flat washer . W ater Pressure W ater softener models Max. 1 MPa (145 psi) Min. 0.1 MPa (14.5 psi) Models without water softener Max. 1 MPa (145 psi) Min. 0.03 MPa (4.3 psi) Impor tant! Adjacent c abinetry must not extend above c avity base Imp ...

  • Fisher & Paykel DD60S 7 - page 11

    11 7b 7c ø 60 mm ø 60 mm max. 5 mm max. 5 mm 220 mm 220 mm 100 mm 100 mm ø 60mm Ser vices can be loc ated either side of dishwasher VENT HOSE VENT HOSE & SERVICES SERVICES Ser vices can be loc ated either side of dishwasher Shelf cutouts Shelf cutouts The ø60 mm services hole should be enlarged to accomodat e the extra venting hose by cutti ...

  • Fisher & Paykel DD60S 7 - page 12

    12 8 MAXIMUM DIST ANCE OF HOSES & CORD FR OM CHASSIS EDGE Lef t ha nd side Right han d side Drain hose - 2000 mm Inlet hose - 1650 mm Venting hose - 1525 mm (Integrated wireless models only) (Integrated wireless models only) Venting hose - 1925 mm Power cord (excl . plug) - 1650 mm Drain hose - 1800 mm Inlet hose - 1250 mm Power cord (excl. pl ...

  • Fisher & Paykel DD60S 7 - page 13

    13 T ALL HEIGHT DESIGNER & INTE GRA TED MODELS FOR 480 mm CA VITY ONL Y - A T T A CH CA VITY BRA CKET 9 The enclosed cavity brack et is  tted before installation in order to conc eal the gap at the top of the cavity left after insta llation. 2 1 Ensure the cavity panel bracket is positioned so that the “F” arrow is pointing towards the f ...

  • Fisher & Paykel DD60S 7 - page 14

    14 REC OMMENDED METHOD (a) - SE CURE WITHOUT DRA WER REMOV AL (FRAMELESS CABINETRY ONL Y) 11a 10a A TT ACH SIDE MOUNTING BRA CKETS F itted Elbow Clip all four side mounting brackets into their slots using a flat-bladed screwdriv er . Ensure they ’ re securely fitted bef ore sliding product into cavity . The mounting slots are in pairs, one on eac ...

  • Fisher & Paykel DD60S 7 - page 15

    15 12a 13a PULL THROUGH HOSE S & MO VE INT O THE CA VITY SE CURE THE DRA WER As you push product in, pull through hoses and cord, ensuring they don ’t get kinked or t wisted. Impor tant! If product cannot be pushed in far enough, pull out again and rearrange hoses and cord . Do not use excessiv e force , as doing so may squash the hoses and l ...

  • Fisher & Paykel DD60S 7 - page 16

    16 11b 10b PULL THROUGH HOSE S & MO VE INT O THE CA VITY F itted Elbow Check that the fitted elbow is rotated left or right (depending on the direction of the routing), then ensure the venting hose is securely attached to it. vent either through same cabinet or adjacent cabinet as per step 7b or 7c AL TERNA TIVE METHOD (b) - SECURE B Y DRA WER ...

  • Fisher & Paykel DD60S 7 - page 17

    17 12b 13b 14b 15b REMO VE THE DRA WER SE CURE THE DRA WER TO THE CABINETR Y REFIT THE DRA WER ONTO THE RUNNER S 2 1 4 5 3 Before r efitting the drawer , ensure the hoses are not twisted and the latches at the rear of each drawer runner are facing for ward. Ensure the release tabs on both sides are reset fully . Ensure the drawer is now rotated clo ...

  • Fisher & Paykel DD60S 7 - page 18

    18 1 2 16 mm x6 2 2 1 Impor tant! Ensure the rubber seal between the drawer and panel is kept in place. REMO VE BRA CKET FROM PRODUCT A T T ACH P ANEL T O PRODUCT A T T ACH P ANEL T O P ANEL BRACKET There must be at least 3 screws used each side When refitting the door pins, ensure they are orientated as shown. Align bottom of panel with bottom of ...

  • Fisher & Paykel DD60S 7 - page 19

    19 ADJUS T P ANEL HEIGHT TO ALIGN THE CABINETR Y GAPS With the front panel fitt ed, insert an appropriately sized Philips screw driver into the hole abov e the door pin and rotate the panel up or down t o align the gaps in your cabinetry. Repeat on the other side if necessary. The panel has a maximum travel of 2 mm up or down. Impor tant! Ensure th ...

  • Fisher & Paykel DD60S 7 - page 20

    20 1 2 16 mm x6 DETERMINE BADGE CUT OUT L OCA TION ROUTE B ADGE WIRING THROUGH P ANEL A T T ACH P ANEL T O P ANEL BRACKET REMO VE BRA CKET & DISCONNE CT BADGE 16b 18b 19b 17b There must be at least 3 screws used each side Align bottom of panel with bottom of bracket 228.5 mm 228.5 mm 127 mm 255 mm 30 mm 25 mm 1 3 4 1 2 1 2 Badge zone INTE GRA T ...

  • Fisher & Paykel DD60S 7 - page 21

    21 2 2 1 A T T ACH P ANEL T O PRODUCT ADJUS T P ANEL HEIGHT TO ALIGN THE CABINETR Y GAPS 20b 22b 21b With the front panel fitt ed, insert an appropriately sized Philips screw driver into the hole abov e the door pin and rotate the panel up or down t o align the gaps in your cabinetry. Repeat on the other side if necessary. The panel has a maximum t ...

  • Fisher & Paykel DD60S 7 - page 22

    22 THERE ARE TWO DIFFERENT PL UMBING AND DRAINAGE OPTIONS. CHOOSE WHICH IS MORE SUIT ABLE. 23 1 3 2 750-882.5 mm 1 2 38 mm max. 120 mm 750-882.5 mm ** 3 4 5 If space is limited for fixing, push hose through drain hose support to required height If space is limited for fixing, push hose through drain hose support to required height Dishw asher using ...

  • Fisher & Paykel DD60S 7 - page 23

    23 27 26 FINAL CHE CKLIS T TROUBLE SHOO TING Check all par ts are installed. Ensure that all panels and parts thereof are secure and final electrical tests hav e been conducted in accordanc e with local electrical regulations. Ensure product is level , securely fastened t o the cabinetry and opens and closes freely . The draw er must be free t o fu ...

Fabricant Fisher & Paykel Catégorie Dishwasher

Les documents que nous recevons du fabricant de l'appareilFisher & Paykel DD60S 7 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Fisher & Paykel
- manuels d’utilisations DD60S 7
- fiches produit Fisher & Paykel
- dépliants
- ou étiquettes-énergie Fisher & Paykel DD60S 7
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Fisher & Paykel DD60S 7.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Fisher & Paykel DD60S 7, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Fisher & Paykel DD60S 7. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Fisher & Paykel DD60S 7.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Fisher & Paykel DD60S 7, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Fisher & Paykel DD60S 7 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Fisher & Paykel DD60S 7.

Le manuel d’utilisation complet Fisher & Paykel, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Fisher & Paykel DD60S 7 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Fisher & Paykel DD60S 7, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lFisher & Paykel DD60S 7 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Fisher & Paykel DD60S 7 - qui devraient nous aider dans les premières étapes lors de l'utilisation Fisher & Paykel DD60S 7
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Fisher & Paykel DD60S 7
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Fisher & Paykel DD60S 7 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Fisher & Paykel DD60S 7?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Fisher & Paykel DD60S 7, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Fisher & Paykel DD60S 7 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)