Français dropdown-ico

Manuel d’utilisation Kathrein UFS 923si

60 pages Non applicable
Télécharger

Aller à la page of 60

Summary
  • Kathrein UFS 923si - page 1

    If you do not know the con fi guration of your satellite reception system, contact your specialist dealer for fi rst installation of the receiver. Operating manual part 1 UFS 923 Connection and start-up English Contents Safety instructions – important notes ........................................................................................ ...

  • Kathrein UFS 923si - page 2

    2 Power cable Make sure that the mains cable (power supply cable) is not damaged. Units with a damaged mains cable must be disconnected from the mains (unplug it at the socket) and repaired by an electrical specialist before setup. Only use the power pack supplied (if available). Risk of death due to electric shock. Danger! Cleaning Disconnect the ...

  • Kathrein UFS 923si - page 3

    3 Periods of extended absence, thunderstorms, mains socket accessibility In order to disconnect the unit from the mains completely , the mains plug must be unplugged from the wall socket! Therefore install the unit close to a mains socket and make sure that socket is accessible at all times, so that you can disconnect the unit from the mains if nec ...

  • Kathrein UFS 923si - page 4

    4 Product return/original packaging Make sure that the fan at the rear of the unit and the ventilation slots on the unit are not blocked or covered in any way . Otherwise the unit may overheat. Adjust the fan speed to the temperature conditions in the receiver . There is a risk of fi re! You must not disconnect the receiver from the mains while it ...

  • Kathrein UFS 923si - page 5

    5 Scope of supply ■ UFS 923 ■ Remote control RC 676 or 675 ■ HDMI cable ■ Loop-through cable ■ Power cable ■ 2 batteries AAA 1.5 V ■ Operating manuals (part 1 and part 2) ■ Safety instructions (multi-lingual) The included accessories may differ from the illustrations. Loop-through cable Power cable Remote control for 250 GB version. ...

  • Kathrein UFS 923si - page 6

    6 Front/rear view of the receiver (front fl ap open) Connection and start-up 1 3 2 4 6 7 9 8 5 100V-240V~ 50/60Hz max. 55W Elektroschock-Gefahr! Nicht öffnen! ON OFF VCR/AUX TV Video Y L Pb Pr R AUDIO KOMP O- NENTEN DIGITAL OUT DiSEqC 1.2 LNB 2 LOOP OUT LNB 1 LOOP OUT LOOP THROUGH IF INPUT 950-2150MHz 14/18V max.400mA 22kHz LNB2 IN LNB1 IN Manifa ...

  • Kathrein UFS 923si - page 7

    7 Connection and start-up * ) CA modules and smart cards are not included with this product ** ) The unit is not fully disconnected from the mains (see the sections "Safety Instructions - Important Instructions" and "Periods of extended absence, thunderstorms, mains socket accessibility") *** ) Accessories (optional) which can b ...

  • Kathrein UFS 923si - page 8

    8 Connection and start-up Remove the cover on the rear of the remote control. Insert the two batteries supplied into the remote control. Ensure correct polarity of the batteries; the + and – markings as indicated inside the battery compartment. Slide the cover back onto the housing until it locks in place. Inserting batteries into the remote cont ...

  • Kathrein UFS 923si - page 9

    9 If you do not know the con fi guration of your satellite reception system, contact your specialist dealer. Connect the Sat IF inputs on the receiver to the satellite reception system. Use coaxial cable with an F standard connector (see illustration on right). 100V-240V~ 50/60Hz max. 55W Elektroschock-Gefahr! Nicht öffnen! ON OFF VCR/AUX TV Vide ...

  • Kathrein UFS 923si - page 10

    10 There are two ways you can access the digital audio. HDMI The stereo audio is transmitted to your TV set via the HDMI interface. If your TV set also supports Dolby Digital, you can also receive the Dolby Digital audio via the HDMI interface (providing it is broadcast by the channel provider). On this issue refer to the operating manual for your ...

  • Kathrein UFS 923si - page 11

    11 If you wish to operate your UFS 923 on a single-cable system, please refer to the con- nection example for single-cable systems (see "T echnical Appendix", "Connection examples") This will only work when receiving one satellite, not in multifeed reception! (Multifeed reception: simultaneous receipt of signals from more than o ...

  • Kathrein UFS 923si - page 12

    12 Before you start to use the UFS 923, read the sections "Safety Instructions - Important Instructions", "Important Information" and "Connection and start-up" through to the item "First installation". Do not connect the unit to the mains until all installation work has been properly carried out. The guidance ...

  • Kathrein UFS 923si - page 13

    13 For this, refer to the operat- ing manual for your TV set and take care to select only those settings that your TV set can process. Press the  (green) button to move to the next menu. The following on-screen display appears: Use the  buttons here to select the basic set- tings for the video and audio output of the receiver to the TV set. V ...

  • Kathrein UFS 923si - page 14

    14 Important instruction for picture output using "YUV": The "YUV" output can be used only if "RGB" is not selected as the output signal for the TV Scart socket! In this case, select "Y/C" or "CVBS" as the output signal for the TV Scart socket the original format is to be transmitted to the TV set, ...

  • Kathrein UFS 923si - page 15

    15 Y ou should perform the tuner con fi guration/make changes yourself only if you are fully familiar with the particulars of your reception system. The settings for the tuner con- fi guration should be made by a specialist engineer for this reception system. Press the  (green) button to move to the next menu. The following on-screen display a ...

  • Kathrein UFS 923si - page 16

    16 Y ou can set up the tuner con fi guration for the following types of reception systems: - DiSEqC™1.0 - DiSEqC™1.1 - Motorised antenna (DiSEqC™1.2/DiSEqC™1.3) - Simple LNB or - One Cable If your reception system is a single-cable system, continue from the item "Single-cable system" in this chapter . Before you start con fi gur ...

  • Kathrein UFS 923si - page 17

    17 Signal con fi guration for tuner 2 (only for "Separate" connection mode) Select the signal con fi guration for tuner 2 here. The currently selected setting is shown graphically in the connection example at the top left of the screen. Either: Same as tuner 1: Both tuners are connected to the same sig- nal source. See example illustrat ...

  • Kathrein UFS 923si - page 18

    18 The following on-screen display appears: Select satellites - tuner 1 Here, you can select up to four available satellites to be included in the signal on tuner 1. Select the satellites you want and con fi rm the your selection with the  button. The selected satellites will be iden- ti fi ed with a check. When you have completed all settings ...

  • Kathrein UFS 923si - page 19

    19 The following on-screen display appears: Satellite con fi guration - tuner 1 Here perform the settings for the fi rst satel- lite for tuner 1. LNB T ype: If your reception system does not have a Universal LNB, use the  buttons to select the LNB types that are used in your reception system. Y ou can choose from the following LNB types: - ...

  • Kathrein UFS 923si - page 20

    20 Connection and start-up DiSEqC™ repeat: The setting for how often the DiSEqC™ command must be repeated depends on the con fi guration of your reception system. - Off DiSEqC™ command is not repeated - 1 DiSEqC™ command is repeated once - 2 DiSEqC™ command is repeated twice - 3 DiSEqC™ command is repeated three times 22 kHz signal: Y ...

  • Kathrein UFS 923si - page 21

    21 Press the  (green) button. The following on-screen display appears: Select satellites - tuner 1 Here select up to a maximum of 64 sat- ellites whose signals should appear at tuner 1. T o do so, select the satellites you want and con fi rm the your selection with the  button. The selected satellites will be identi fi ed with a check. When ...

  • Kathrein UFS 923si - page 22

    22 The following on-screen display appears: LNB T ype: If your reception system does not have a Universal LNB, use the  buttons to select the LNB types that are used in your reception system. Y ou can choose from the following LNB types: - Universal or - Simple or - User-de fi ned Connection and start-up Satellite con fi guration - tuner 1 ...

  • Kathrein UFS 923si - page 23

    23 Connection and start-up DiSEqC™ repeat: The setting for how often the DiSEqC™ command must be repeated depends on the con fi guration of your reception system. Refer to the documentation for your reception system or seek assistance from a specialist engineer . - Of f DiSEqC™ command is not repeated - 1 DiSEqC™ command is repeated once - ...

  • Kathrein UFS 923si - page 24

    24 Press the  (green) button. The following on-screen display appears: Select satellites - tuner 1 Here select up to max. 64 satellites whose signals should appear at tuner 1. T o do so, select the satellites you want and con fi rm the your selection with the  button. The selected satellites will be identi fi ed with a check. When you have ...

  • Kathrein UFS 923si - page 25

    25 The following on-screen display appears: Motor Control Here select the control type "DiSEqC™1.2". For this, refer to the documentation for your motorised antenna. Go to zero position Select the selection fi eld "Go to zero posi- tion". Press the  button to instruct the turntable to move to its zero position. Set borders ...

  • Kathrein UFS 923si - page 26

    26 If you subsequently wish to delete the set limits, switch to the selection fi eld "Reset limit positions" and press the  button to con fi rm deletion of the limits. Y ou can then set new values for the limits. Once you have set all the limits, press the  button. Press the  (green) button to move to the next menu. The followi ...

  • Kathrein UFS 923si - page 27

    27 Rotate antenna: Select the "Move motorised antenna" selection fi eld. Here you can control the movements of the motorised antenna, using the following buttons:  Start slow rotation to the west  Rotate to the west step by step  Stop the current movement  Rotate to the east step by step  Start slow rotation to the east Se ...

  • Kathrein UFS 923si - page 28

    28 Motor Control Here select the control type "DiSEqC™1.3". For this, refer to the documentation for your motorised antenna. My longitude Select the fi eld "My Longitude" and use the number pad here to enter your actual longitude. My latitude Select the "My Latitude" fi eld and use the number pad to enter your curr ...

  • Kathrein UFS 923si - page 29

    29  Start slow rotation to the east Once you have reached the desired east / west limit, switch to the respective fi eld "Set current position for "****" limit" and press the  button to con fi rm. If you subsequently wish to delete the set limits, switch to the selection fi eld "Reset limit positions" and pres ...

  • Kathrein UFS 923si - page 30

    30 T est transponder: Select the "T est T ransponder" selection fi eld. Here you can select a transponder for checking the signal strength bar and signal quality bar to see whether your settings are correct. When you have completed all settings for this satellite, press the  (green) button. The receiver will now save these values for ...

  • Kathrein UFS 923si - page 31

    31 Press the  (green) button. The following on-screen display appears: Select satellites - tuner 1 Select the satellite whose signal is present on tuner 1, and press the  button to con fi rm your selection. The selected satel- lite will be identi fi ed with a check. Once you have selected the required satel- lites, press the  (green) but ...

  • Kathrein UFS 923si - page 32

    32 LNB T ype: If your reception system does not have a Universal LNB, use the  buttons to select the LNB types that are used in your reception system. Y ou can choose from the following LNB types: - Universal or - Simple or - User-de fi ned LNB frequency (MHz): Y ou only need to specify this data if your LNB type is not "Universal LNB&q ...

  • Kathrein UFS 923si - page 33

    33 Use the  buttons to select "On" in the "Single-cable system used" line. Then use the  buttons to switch to the "Single-cable system" selection fi eld. The following on-screen display appears: Select the single-cable system used in your reception system: - EXR .../EXU ... For all Kathrein single-cable ma ...

  • Kathrein UFS 923si - page 34

    34 The following on-screen display appears: Select satellites - tuner 1 Here select up to max. two satellites whose signals should appear at tuner 1. Select the satellites you want and con fi rm the your selection with the  button. The selected satellites will be identi fi ed with a check. When you have completed all settings, press the  (g ...

  • Kathrein UFS 923si - page 35

    35 Refer to the documentation supplied with your system for the settings for the SCRs, frequencies and any PIN assigned to the tuner . Y ou will fi nd there a printed list showing the assignment between the various SCRs and the respective transmission frequen- cies. Y ou may not be able to freely select the PIN for protection of individual frequen ...

  • Kathrein UFS 923si - page 36

    36 The following on-screen display appears: LNB type (settings): If your reception system does not have a Universal LNB, use the  buttons to select the LNB types that are used in your reception system. Y ou can choose from the following LNB types: - Universal or - Simple or - User-de fi ned LNB frequency (MHz): Y ou only need to specify this ...

  • Kathrein UFS 923si - page 37

    37 Press the  (green) button. The following on-screen display appears: Select satellites - tuner 1 Here select the satellites whose signals appear at tuner 1. T o do so, select the sat- ellites you want and con fi rm the your selec- tion with the  button. When you have selected all the satellites you want, press the  (green) button. The f ...

  • Kathrein UFS 923si - page 38

    38 T ransmission channel for tuner 1: Select a free available transmission channel (SCR 0 - SCR 3). T ransmission channel for tuner 2: Select a free available transmission channel (SCR 0 - SCR 3). When you have completed all settings for the satellite, press the  (green) button. The following on-screen display appears: T est transponder: Select ...

  • Kathrein UFS 923si - page 39

    39 The following on-screen display appears: Select satellites - tuner 1 Here select up to max. two satellites whose signals should appear at tuner 1. T o do so, select the satellites you want and con fi rm the your selection with the  button. The selected satellites will be identi fi ed with a check. Press the  (green) button. Single-cable ...

  • Kathrein UFS 923si - page 40

    40 Refer to the documentation supplied with your system for the settings for the SCRs, frequencies and any PIN assigned to the tuner . Y ou will fi nd there a printed list showing the assignment between the various SCRs and the respective transmission frequen- cies. Y ou may not be able to freely select the PIN for protection of individual frequen ...

  • Kathrein UFS 923si - page 41

    41 Perform the settings for the second tuner in the same way as for the fi rst tuner . When you have completed all settings, press the  (green) button. The following on-screen display appears: LNB type (settings): If your reception system does not have a Universal LNB, use the  buttons to select the LNB types that are used in your recepti ...

  • Kathrein UFS 923si - page 42

    42 If you have selected more than one satellite for tuner 1, the receiver will automatically skip to the settings for the second satellite. Now perform the settings for the second satellite in the same way as described for the fi rst satellite. Once you have completed the settings for the satellites assigned, the receiver will automatically displa ...

  • Kathrein UFS 923si - page 43

    43 If you do not wish to perform a channel search, press the  (green) button and continue with the section "Date and T ime". If you want to perform a channel search, use the  buttons to select "Y es". The following on-screen display appears: Country Select Using the  buttons you can select whether the channels fou ...

  • Kathrein UFS 923si - page 44

    44 Channel search mode Use the  buttons to select the type of channels that are to be searched for . Y ou have three options: - "free-to-air and encrypted" All channels are searched for - "only free" Only free-to-air channels are searched for - "only scrambled" Only encrypted channels are searched for T o view en ...

  • Kathrein UFS 923si - page 45

    45 Local UTC offset (time zone difference) Here you can select the local time offset to UTC (formerly GMT) (e.g. for Germany: + 1 hour). Y ou can set the offset in 30 minute steps. The maximum offset is 1 1 hours and 30 minutes (+ and -). Date and time Connection and start-up When you have made the settings, press the  (green) button, to complet ...

  • Kathrein UFS 923si - page 46

    46 Connection and start-up On completion of a successful fi rst installation (TV picture can be seen) we recommend having the receiver search for any available software update. It is a prerequisite that you have selected (included in the selection) the satellite ASTRA 19.2° East in the fi rst installation. Press the  button to switch to the m ...

  • Kathrein UFS 923si - page 47

    47 Connection and start-up Always follow the operating instructions from your Pay TV provider and the instruc- tions supplied with the smart card and the CA (conditional access) module! Smart cards and CA modules are not included with this product! The cards and modules are issued by the respective Pay TV providers, and contain the sub- scriber dat ...

  • Kathrein UFS 923si - page 48

    48 T roubleshooting In the event of a malfunction, fi rst check all the cable connections and operating states: 1. Receiver and TV set power plugs are connected to wall socket 2. Antenna cables on receiver input 3. Receiver and TV set correctly connected by a HDMI or Scart cable 4. Audio connections are made to Hi-Fi or Dolby Digital system as app ...

  • Kathrein UFS 923si - page 49

    49 Service If, despite studying this operating manual, you still have questions about getting started with the unit or using it correctly, or if unexpected problems occur, please contact your specialist dealer. ...

  • Kathrein UFS 923si - page 50

    50 T echnical Appendix Advanced connection example 100V-240V~ 50/60Hz max. 55W Elektroschock-Gefahr! Nicht öffnen! ON OFF VCR/AUX TV Video Y L Pb Pr R AUDIO KOMPO - NENTEN DIGITAL OUT DiSEqC 1.2 LNB 2 LOOP OUT LNB 1 LOOP OUT LOOP THROUGH IF INPUT 950-2150MHz 14/18V max.400mA 22kHz LNB2 IN LNB1 IN Manifactured under license from Dolby Laboratories. ...

  • Kathrein UFS 923si - page 51

    51 T echnical Appendix T echnical Speci fi cations T ype UFS 923/250 GB UFS 923/1000 GB Article no./colour 20210190/silver - 20210191/black 20210182/silver - 20210183/black RF section Sat IF band MHz 950-2150 Input level band dB μ V 44-83 Modulation, FEC, demultiplexer DVB-S-/DVB-S2 standard Video resolution CCIR 601 (720 x 576 lines), 576p, 720p ...

  • Kathrein UFS 923si - page 52

    52 T echnical Appendix Sat IF connection examples 2 x UAS 571 Sat-ZF 950-2150 MHz **) ESD../ESC.. EXR 21 Signal 1 Signal 2 Position OPTION UC1 ** ) Overvoltage protection KAZ 1 1/KAZ 12 Individual reception systems Community antenna network systems (4 x Sat IF) ...

  • Kathrein UFS 923si - page 53

    53 T echnical Appendix ** ) Overvoltage protection KAZ 1 1/KAZ 12 Community antenna network systems (8 x Sat IF), multi-feed Community antenna network systems (16 x Sat IF), multi-feed ...

  • Kathrein UFS 923si - page 54

    54 T echnical Appendix ** ) Overvoltage protection KAZ 1 1/KAZ 12 Single cable systems ...

  • Kathrein UFS 923si - page 55

    55 T echnical Appendix ** ) Overvoltage protection KAZ 1 1/KAZ 12 ...

  • Kathrein UFS 923si - page 56

    56 T echnical Appendix Connection examples for network functionality 100V-240V~ 50/60Hz max. 55W Elektroschock-Gefahr! Nicht öffnen! ON OFF VCR/AUX TV Video Y L Pb Pr R AUDIO KOMPO - NENTEN DIGITAL OUT DiSEqC 1.2 LNB 2 LOOP OUT LNB 1 LOOP OUT LOOP THROUGH IF INPUT 950-2150MHz 14/18V max.400mA 22kHz LNB2 IN LNB1 IN Manifactured under license from D ...

  • Kathrein UFS 923si - page 57

    57 T echnical Appendix 100V-240V~ 50/60Hz max. 55W Elektroschock-Gefahr! Nicht öffnen! ON OFF VCR/AUX TV Video Y L Pb Pr R AUDIO KOMPO - NENTEN DIGITAL OUT DiSEqC 1.2 LNB 2 LOOP OUT LNB 1 LOOP OUT LOOP THROUGH IF INPUT 950-2150MHz 14/18V max.400mA 22kHz LNB2 IN LNB1 IN Manifactured under license from Dolby Laboratories. Dolby and the double-D symb ...

  • Kathrein UFS 923si - page 58

    58 T echnical Appendix 100V-240V~ 50/60Hz max. 55W Elektroschock-Gefahr! Nicht öffnen! ON OFF VCR/AUX TV Video Y L Pb Pr R AUDIO KOMPO- NENTEN DIGITAL OUT DiSEqC 1.2 LNB 2 LOOP OUT LNB 1 LOOP OUT LOOP THROUGH IF INPUT 950-2150MHz 14/18V max.400mA 22kHz LNB2 IN LNB1 IN Manifactured under license from Dolby Laboratories. Dolby and the double-D symbo ...

  • Kathrein UFS 923si - page 59

    59 T echnical Appendix 100V-240V~ 50/60Hz max. 55W Elektroschock-Gefahr! Nicht öffnen! ON OFF VCR/AUX TV Video Y L Pb Pr R AUDIO KOMPO - NENTEN DIGITAL OUT DiSEqC 1.2 LNB 2 LOOP OUT LNB 1 LOOP OUT LOOP THROUGH IF INPUT 950-2150MHz 14/18V max.400mA 22kHz LNB2 IN LNB1 IN Manifactured under license from Dolby Laboratories. Dolby and the double-D symb ...

  • Kathrein UFS 923si - page 60

    Internet: www .kathrein.de KA THREIN-Werke KG • Anton-Kathrein-Strasse 1 - 3 • Postfach 10 04 44 • 83004 Rosenheim • Germany • T el +49 8031 184-0 • Fax +49 8031 184-385 936.4046/-/ZWT/021 1/e - Subject to change. ...

Fabricant Kathrein Catégorie Receiver

Les documents que nous recevons du fabricant de l'appareilKathrein UFS 923si peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Kathrein
- manuels d’utilisations UFS 923si
- fiches produit Kathrein
- dépliants
- ou étiquettes-énergie Kathrein UFS 923si
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Kathrein UFS 923si.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Kathrein UFS 923si, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Kathrein UFS 923si. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Kathrein UFS 923si.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Kathrein UFS 923si, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Kathrein UFS 923si par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Kathrein UFS 923si.

Le manuel d’utilisation complet Kathrein, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Kathrein UFS 923si - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Kathrein UFS 923si, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lKathrein UFS 923si qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Kathrein UFS 923si - qui devraient nous aider dans les premières étapes lors de l'utilisation Kathrein UFS 923si
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Kathrein UFS 923si
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Kathrein UFS 923si dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Kathrein UFS 923si?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Kathrein UFS 923si, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Kathrein UFS 923si il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)