Français dropdown-ico

Manuel d’utilisation Delta 22-610

24 pages 3.07 mb
Télécharger

Aller à la page of 24

Summary
  • Delta 22-610 - page 1

    INSTRUCTION MANUAL P ART NO. 428-08-651-0001 06-1 5 -05 Copyright © 2005 Delta Machinery 24 3 / 4 " Planer (Model 22-610, Thr ee Phase) T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). ...

  • Delta 22-610 - page 2

    2 T ABLE OF CONTENTS Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to r educe the risk of personal injury . Improper operation, maintenance or modification of tools or equipment could r esult in serious injury and prop ...

  • Delta 22-610 - page 3

    3 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury . Used without the saf ...

  • Delta 22-610 - page 4

    4 GENERAL SAFETY RULES READ AND UNDERST AND ALL W ARNINGS AND OPERA TING INSTRUCTIONS BEFORE USING THIS EQUIPMENT . Failure to follow all instructions listed below , may result in electric shock, fire, and/or serious personal injury or pr operty damage. IMPORT ANT SAFETY INSTRUCTIONS 1. FOR YOUR OWN SAFETY , READ THE INSTRUCTION MANUAL BEFORE OPERA ...

  • Delta 22-610 - page 5

    5 ADDITIONAL SPECIFIC SAFETY RULES SA VE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. 1. DO NOT OPERA TE THIS MACHINE until it is completely assembled and installed according to the instructions. A machine incorrectly assembled can cause serious injury . 2. OBT AIN ADVICE fr om your supervisor , instructor , or another q ...

  • Delta 22-610 - page 6

    6 A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cor ds which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s plug. Before connec ...

  • Delta 22-610 - page 7

    7 UNP ACKING AND CLEANING Carefully unpack the machine and all loose items fr om the shipping container(s). Remove the protective coating fr om all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gaso- line or lacquer thinner for this purpose). After cleaning, cover the unpainted surfac ...

  • Delta 22-610 - page 8

    8 ASSEMBL Y ASSEMBL Y TOOLS REQUIRED ASSEMBL Y TIME ESTIMA TE - 2-3 hours * Open end wrenches (supplied) * Hex wrenches (supplied) * Flat screwdriver (not supplied) UNLOADING AND POSITIONING MACHINE This machine should be unloaded using a crane and slings around and under the table on both sides, as shown in Fig. 2. Lift the machine slowly , making ...

  • Delta 22-610 - page 9

    9 T o connect power to your machine, proceed as follows for either 200-230/460 volts, three phase operation. 1. Remove the four screws, one of which is shown at (A) Fig. 4, and remove cover (B). 2. Insert power line through entrance hole (E) and con- nect the three power lines to terminals L1, L2 and L3 (shown at C). The green gr ound wire should b ...

  • Delta 22-610 - page 10

    10 OPERA TION OPERA TIONAL CONTROLS AND ADJUSTMENTS ST ARTING AND STOPPING THE PLANER The machine is started by pressing the gr een (shroud- ed) "ON" button (A) and stopped by pressing the r ed (mushroom type) "OFF" button (B), as shown in Fig. 8. Fig. 8 T ABLE RAISING AND LOWERING CONTROLS DISCONNECT MACHINE FROM POWER SOURCE F ...

  • Delta 22-610 - page 11

    11 Fig. 12 T o change feed roll speeds, make sure the feed r oll engagement lever (A) Fig. 12, is disengaged (in the down position) and open the left side door of the machine. When the belt (C) is on the smallest step of the motor pulley (D) and the lar gest step of the gearbox pulley (E), the feed roll speed will be 25 feet per minute. When the be ...

  • Delta 22-610 - page 12

    12 Fig. 16 Fig. 17 Fig. 18 CHECKING AND ADJUSTING BEL T TENSION DRIVE BEL T TENSION: Proper drive belt tension is obtained when there is zer o deflection, using light finger pressur e, on drive belts (A) Fig. 16, midway between pul- leys. If an adjustment is necessary , push down on lever (B) Fig. 16, to disenguage feed roller . Loosen jam nut (C) ...

  • Delta 22-610 - page 13

    13 CHECKING, ADJUSTING AND REPLACING KNIVES 1. When checking, adjusting or replacing the cutter- head knives on the planer , proceed as follows: A. DISCONNECT MACHINE FROM POWER SOURCE B. Remove the top cover of the planer exposing the cutterhead. C. Check all four knives for pr oper setting using the knife guage (A), as shown in Fig. 20. When the ...

  • Delta 22-610 - page 14

    14 Fig. 21 Fig. 22 Fig. 22A LEVELING THE T ABLE The table must be parallel to the cutterhead knives. T o check and adjust, proceed as follows: 1. DISCONNECT MACHINE FROM POWER SOURCE 2. Remove the four screws that attach the top cover to the planer and carefully r emove the top cover . 3. Place a straight edge (A) Fig. 21, on the ground sur- faces ...

  • Delta 22-610 - page 15

    15 Fig. 23A Fig. 23B Fig. 23D Fig. 23C CHECKING AND ADJUSTING BED ROLL HEIGHT The height of the bed rolls (A) and (E) Fig. 23A, should be set between .002" and .004" above the table surface, with the bed rolls at their lowest position. T o check the infeed bed roller height setting, pr oceed as follows: 1. DISCONNECT MACHINE FROM POWER SO ...

  • Delta 22-610 - page 16

    16 Fig. 24B Fig. 25 Fig. 26 ADJUSTING PRESSURE BAR IMPORT ANT : TH E PRESSURE BAR IS SET A T THE F ACTOR Y AND SHOULD NOT NEED ASJUSTMENT . BUT WHEN KNIVES ARE SHARPENED OR REPLACED THE PRESSURE BAR SETTING SHOULD BE CHECKED AND ADJUSTED IF NECESSAR Y . The pressur e bar is located directly behind the cutter- head and rides on the planed surface of ...

  • Delta 22-610 - page 17

    17 ADJUSTING THE CHIPBREAKER The chipbreaker is located on the top of the planer and extends down around the fr ont of the cutterhead. The chip-breaker segments raise as stock is fed thr ough and "break or curl" the chips the same as the plane ir on cap on a hand plane. The bottom of the chipbreaker must be parallel to the knives and set ...

  • Delta 22-610 - page 18

    18 ADJUSTING SPRING TENSION ON FEED ROLLERS The outfeed roll (A) Fig. 33, and infeed r oll (not visible) are those parts of your planer that feed the stock while it is being planed. The feed rolls ar e under spring tension and this tension must be sufficient to feed the stock uni- formly through the planer without slipping but should not be too tig ...

  • Delta 22-610 - page 19

    19 Fig. 38 Fig. 39 Fig. 40 ADJUSTING CHIP DEFLECTOR 1. DISCONNECT MACHINE FROM POWER SOURCE 2. Remove the cutterhead guard. 3. The edge (C) of the chip deflector (A) Fig. 38, should be adjusted so it is a minimum of .040" and a maximum of .080" away from the cutting cir cle. Place a feeler gauge between the knife and the edge of the chip ...

  • Delta 22-610 - page 20

    20 When using your machine, follow these few simple steps for achieving the best results. 1. T rue Up One Face – Feed one face of the board over a jointer , making thin cuts with each pass, until the entire surface is flat. 2. Plane to Thickness – Place the side you planed in STEP 1 face down and feed the board thr ough the planer . Plane until ...

  • Delta 22-610 - page 21

    21 P ARTS, SERVICE OR W ARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standards and ar e serviced by a network of Porter -Cable • Delta Factory Service Centers and Delta Authorized Service Stations. T o obtain additional information regar ding your Delta quality product or to obtain parts, service, warra ...

  • Delta 22-610 - page 22

    22 NOTES ...

  • Delta 22-610 - page 23

    23 NOTES ...

  • Delta 22-610 - page 24

    The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas registradas de POR TER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T ...

Fabricant Delta Catégorie Planer

Les documents que nous recevons du fabricant de l'appareilDelta 22-610 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Delta
- manuels d’utilisations 22-610
- fiches produit Delta
- dépliants
- ou étiquettes-énergie Delta 22-610
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Delta 22-610.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Delta 22-610, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Delta 22-610. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Delta 22-610.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Delta 22-610, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Delta 22-610 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Delta 22-610.

Le manuel d’utilisation complet Delta, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Delta 22-610 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Delta 22-610, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lDelta 22-610 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Delta 22-610 - qui devraient nous aider dans les premières étapes lors de l'utilisation Delta 22-610
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Delta 22-610
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Delta 22-610 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Delta 22-610?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Delta 22-610, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Delta 22-610 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)