Français dropdown-ico

Manuel d’utilisation Epson C82305

29 pages 0.17 mb
Télécharger

Aller à la page of 29

Summary
  • Epson C82305 - page 1

    EPSON Serial Interface Card C82305* C8230* English Deutsch Français ESpañol Italiano 4000152 C01-00 ...

  • Epson C82305 - page 2

    NOTICE All rights reserved. Reproduction of any part of this manual in any form whatsoever without Seiko Epson’s express written permission is forbidden. The contents of this manual are subject to change without notice. All efforts have been made to ensure the accuracy of this manual. However, should any error S be detected. Seiko Epson would gre ...

  • Epson C82305 - page 3

    Serial Interface C82305 * /C82306 * Schnittstellenkarte C82305 * /C82306 * Interface série C82305 * /C82306* English Deutsch Français Español Italiano Interface en serie C82305 * /C82306* Interfaccia seriale C82305* /C82306* ...

  • Epson C82305 - page 4

    TABLE OF CONTENTS INTRODUCTION About this guide SETTING THE CONDITIONS Card layout DIP switch and jumper settings DIP switches Jumpers DATA ENTRY Serial communication About data entry Handshaking protocol SPECIFICATIONS HARDWARE DESCRIPTION RECOMMENDED CIRCUIT CONNECTIONS INSTALLATION 2 3 4 4 5 5 10 13 13 13 14 17 19 21 22 ...

  • Epson C82305 - page 5

    INTRODUCTION The Serial Interface Card 032305 * /C82306 * is an interface that allows asynchronous serial data communication between a host computer and an EPSON printer. This interface card offers the following features: • Data transmission that can be set at either RS-232D or 20 mA Current Loop levels (RS-232D has been revised from the former R ...

  • Epson C82305 - page 6

    About this guide This guide is designed to give you detailed information on how to install your C82305 * /C82306 * serial interface card in a variety of EPSON printers. Installation procedures vary slightly depending upon the printer model that you have. Also included are instructions on how to adjust the settings of the C82305 * /C82306 * interfac ...

  • Epson C82305 - page 7

    SETTING THE CONDITIONS The C82305 * /C82306 * interface card has two sets of DIP (Dual In-line Package) switches, and seven jumpers. These switches and jumpers are used for selecting various interface operations. Card layout The figure below shows the layout of the C82305 * /C82306 * card, and the locations of the DIP switches and jumpers. Figure 1 ...

  • Epson C82305 - page 8

    DIP switch and jumper settings Before you install the C82305 * /C82306 * interface, you may need to adjust the DIP switch 2 and jumper settings. You can change the DIP switch 1 settings after you install the interface. When making DIP switch setting changes, it is best to use a pointed device, such as a ball-point pen or small screwdriver. Caution ...

  • Epson C82305 - page 9

    DIP switch 1 (interface operations) The table below contains information on switch functions, and the factory setting of each. Table 1. DIP switch 1 Switch Function ON OFF Factory number setting 1-1 I/F card enable/disable Disable ON (Note) Enable l-2 Word length l-3 Parity check 1 1-4 Parit y chec k 2 I 8 bit 7 bit ON OFF Se e Tabl e 4. OFF l-5 l- ...

  • Epson C82305 - page 10

    DIP switch 2 (interface operations) The table below contains information on switch functions, and the factory setting of each. Table 2. Data word structure The data word structure is also operator selectable through DIP switch settings (See Table 1). The word structure for serial data is: 1 start bit +7 or 8 data bits (selectable) + 1 parity bit (s ...

  • Epson C82305 - page 11

    The table below shows the possible word structure combinations. Table 3. Word structure You can select the parity check method by DIP switch settings. (See Table 4.) Table 4. Parity check Note Since the selection of parity check depends on your type of printer, refer to your printer’s manual for details. ...

  • Epson C82305 - page 12

    Baud rate selection In serial data communication, data is transmitted in the form of bits. These data bits go out one at a time along a single path, and in a specified order. The BPS (Bits Per Second) rate, or speed at which these bits are transmitted, can be selected using a combination of DIP switch settings. Note In the current loop mode, accura ...

  • Epson C82305 - page 13

    Note • The printer will assume a setting of 1,200 BPS for switch combinations other than those shown above. • Since the maximum transmission speed (baud rate) depends on your type of printer, refer to your printer’s manual for details. Jumpers The jumper is a small terminal used for connecting or disconnecting a circuit. The jumper is on when ...

  • Epson C82305 - page 14

    Jumper settings Table 6. shows information about the interface conditions that can be selected using jumpers. In all cases, ON denotes the connection of the jumper (covering both terminals), while OFF denotes the disconnection of the jumper. Table 6. Jumper settings Note If the host computer is not equipped with a power supply for the Current Loop ...

  • Epson C82305 - page 15

    Table 7. Flag polarity selection Jumper Function Factory setting ON: MARK (do not accept data) = JNOR Current ON ON J5 JREV ON: MARK (do not accept data)= Negative EIA level ON: MARK (do not accept data) = Current OFF ON: MARK (do not accept data)= Positive EIA level OFF Note Either the JNOR or JREV jumper must be connected. 12 ...

  • Epson C82305 - page 16

    DATA ENTRY This section gives a brief description of serial data communication conditions and handshaking protocols supported by the C82305 * /C82306 * interface card. Serial data communications The CL32305 * /C82306 * interface allows you to select either RS-232D or 20 mA Current Loop signal levels; but never both at the same time. This interface ...

  • Epson C82305 - page 17

    Handshaking protocol DTR and X-on/X-off handshaking protocols can be performed under either RS-232D or 20mA Current Loop transmission. X-on/X-off Protocol X-on/X-off protocol is a system in which the printer transmits a code to the computer to indicate that it cannot accept more data, and a second code when it is once again ready. The C82305* /C823 ...

  • Epson C82305 - page 18

    • Transmit timing of X-on signal The X-on signal is transmitted when the power is first turned on, or when the vacant area in the buffer is greater than the specified value (typically 512 bytes; refer to your printer manual). Figure 3. X-on/X-off thing X-ON X-OFF X-ON POWER ON Buffer capacity less than specified value Buffer capacity greater than ...

  • Epson C82305 - page 19

    With the status flag set, and data reception prohibited, the vacant area of the buffer gradually increases as the printer continues to print. When the vacant area in the buffer reaches the specified value (typically 512 bytes; refer to your printer manual), the flag is reset and data entry is again enabled. Note Reverse Channel pin (No. 11) and DTR ...

  • Epson C82305 - page 20

    SPECIFICATIONS 1. Synchronization: Asynchronous 2. Baud Rate: 75, 110, 134.5, 150, 200, 300, 600, 1,200, 1,800, 2,400, 4,800, 9,600, or 19,200 BPS (selectable) 3. Word length: Start bit: 1 bit Data bit: 7 or 8 bits (selectable) Parity bit: Odd, even, none, or ignore (selectable) Stop bit: 1 bit or more 4. Input signal polarity: 1) With RS-232D: MAR ...

  • Epson C82305 - page 21

    5. Handshaking Table 8. Handshaking Using DTR protocol Using X-ON/X-OFF protocol US-232D The two signal The impedance conditions at pm No. between pin No. 17 11 and pin No. 20 are and pin No. 24 is as as follows; follows; MARK-data entry is LOW(MARK)-data disabled entry is disabled SPACE-data entry is High(SPACE)-data enabled entry is enabled Data ...

  • Epson C82305 - page 22

    HARDWARE DESCRIPTION 1. I/F board connector: EIA standard 25-pin D-SUB female connector. 2. For signal description and pin assignment, refer to the table below: Table 9. Signal Description and Pin Assignment Pin No. Signal name Direction Description 1 protective Ground — Chasis ground Transmitted 2 Data (TXD) Text Transmitted serial data 3 Receiv ...

  • Epson C82305 - page 23

    Pin No. Signal Name Direction* 17 TTY-TXD out 24 TTFTXD Return Description High impedance (‘SPACE’) between pin No. 17 and No 24 or an X-on signal sent across pin No. 17 and No. 24 indicates that the printer is ready to accept data. Low impedance (‘MARK’) or an X-off signal being sent indicates that the printer is busy. Operator can invert ...

  • Epson C82305 - page 24

    RECOMMENDED CIRCUIT CONNECTIONS Recommended line driver and line receiver for RS-232D signal level settings. (As viewed from the host computer.) Figure 4. RS-232D Line Receiver Serial Interface Card Recommended line interface circuit for 20mA Current Loop signal level settings. (As viewed from the host computer.) Figure 5. Current Loop Note The val ...

  • Epson C82305 - page 25

    INSTALLATION The C82305* /C82306* interface card is designed to be installed inside the printer. Installation or removal of the interface board is easy, and requires only a screwdriver. The following section gives you detailed information on how to install your interface card in a variety of EPSON printers. Caution • Turn off the power to the pri ...

  • Epson C82305 - page 26

    inside the compartment. 2. Fit both sides of this interface card into the guides 3. Insert this interface card until the interface pins mate with the connector inside your printer. 4. Secure the interface with the two screws. 23 ...

  • Epson C82305 - page 27

    Current-Loop Transmitter/Receiver Circuit Diagrams Set the Jumper Jl, J2, J3, and J4 referring to the following diagrams. Transmitter Circuit Diagram 121 ...

  • Epson C82305 - page 28

    Receiver Circuit Diagram 122 ...

  • Epson C82305 - page 29

    EPSON OVERSEAS MARKETING LOCATIONS EPSON AMERICA. INC. 2780 Lomita Blvd. Torrance. Cailif. 90505. U S A Phone (213) 539-9140 Fax (213) 534-5854 EPSON UK LTD. campus 100. Maylands Avenue. Hemel, Hempstead. Herts. HP2 7EZ, UK Phone: 442-61144 Telex: 5182467 EPSON AUSTRALIA PTY. LTD. Unit 3, 17 Rodborough Road. Frenchs Forest NSW 2086 Australia Phone: ...

Fabricant Epson Catégorie Network Card

Les documents que nous recevons du fabricant de l'appareilEpson C82305 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Epson
- manuels d’utilisations C82305
- fiches produit Epson
- dépliants
- ou étiquettes-énergie Epson C82305
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Epson C82305.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Epson C82305, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Epson C82305. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Epson C82305.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Epson C82305, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Epson C82305 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Epson C82305.

Le manuel d’utilisation complet Epson, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Epson C82305 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Epson C82305, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lEpson C82305 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Epson C82305 - qui devraient nous aider dans les premières étapes lors de l'utilisation Epson C82305
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Epson C82305
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Epson C82305 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Epson C82305?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Epson C82305, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Epson C82305 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)