Français dropdown-ico

Manuel d’utilisation Craftsman 137.219

24 pages 4.58 mb
Télécharger

Aller à la page of 24

Summary
  • Craftsman 137.219 - page 1

    Operator's ManuaM .3 10 in. DRILL PRESS With Laser Trac ® Model No, 137,219000 CAUTION: Before using this DriJl Press, read this manual and follow all its Safety Rules and Operating Instructions o Safety Instructions o Installation ® Operation o Maintenance • Parts List Customer He_p Line 1-80@-843-1682 Sears, Roebuck and Co., Hoffman Esta ...

  • Craftsman 137.219 - page 2

    SECTmON PAGE Warranty ........................................ 2 Product Specifications ....................... 2 Power Tool Safety ............................. 3 Drill Press Safety .................................. 4 Electrical Requirements and Safety ...... 5 Accessories and Attachments .............. 6 Tools Needed For Assembly ............... ...

  • Craftsman 137.219 - page 3

    GENERAL SAFETY mNSTRUCTmONS BEFORE USING THIS DRILL PRESS Safety is a combination of common sense, stay alert and knowing how to use your dril! press. [AWARN NG I To avoid mistakes that could cause serious injury, do not plug the drill press in until you have read and understood the following. 1. READ and become familiar with the entire instruction ...

  • Craftsman 137.219 - page 4

    [AWARNING I For your own safety, do not try to use your drill press or plug it in until it is completely assembled and installed according to the instructions, and until you have read and understood this instruction manual: 1. YOUR DRILL PRESS MUST BE BOLTED securely to a workbench. In addition, if there is any tendency for your drill press to move ...

  • Craftsman 137.219 - page 5

    GROUNDING INSTRUCTIONS tNTHE EVENT OF A _,_ALFUNCTION OR BREAKDOWN, grounding provides a path of least resistance forelectric current and reduces the risk of shock. This tool is equipped with an electric cordthat has an equipment grounding conductor andgrounding plug. The plug MUST be plugged into a matching receptacle thatis properly installed and ...

  • Craftsman 137.219 - page 6

    RECOMMENDED ACCESSORmES [AWARN NG I Use only accessories recommend for this drill press. Follow instructions that accompany accessories. Use of improper accessories may cause hazards. Visit your Sears Hardware Department or see the Sears Power and hand Tool Catalog for the follow accessories: Drill bits Hold-Down Clamps Drill press Vises [ WARN NG ...

  • Craftsman 137.219 - page 7

    UNPACKING AND CHECKING CONTENTS D E H I WWWW K N O # DD Q S R ...

  • Craftsman 137.219 - page 8

    Belt spee_ Oo Quill retu Depth stop nuts Depth scale pointer - --C / Depth scale in coil / spring Rack ring Table bracket Spindle pulley Motor pulley Table bracket lock handle Bevel lock bolt Pulley cover Belt speed sight window Base Fence endstop ON/OFF Motor switch with safety key Belt tension lock knob Laser guide Chuck Head locking screw Bevel ...

  • Craftsman 137.219 - page 9

    BASE - Supports dril! press. For additional stability, holes are provided in base to bolt drill press to workbench. BACKUP MATERIAL - A piece of scrap wood placed between the workpiece and table. The backup board prevents wood in the workpiece from splintering when the drill passes through the backside of the workpiece. It also prevents drilling in ...

  • Craftsman 137.219 - page 10

    ASSEMBLY JNSTRUCTmONS [AWARNmNG 1 For your own safety, never connect plug to power source outlet until all assembly steps are complete and you have read and understood the safety and operating instructions. [AWARN NG I The drill press is a heavy power too! and should be lifted with the help of two PEOPLE OR MORE to safely assemble it. ASSEMBUNG COL ...

  • Craftsman 137.219 - page 11

    4_ Slide the table assembly withtherack onto the column. 5_ Engage the bottom of the rack (5) with the lip of the column support (6)_ Tighten thetable bracket lock handle (4) to lock the table assembly tothe column. Fig.D 7_ Instal! the table crank handle (9) ontothe worm gear shaft (11 ) on the side of the table support (12)_ 8_ Line upthe flatsid ...

  • Craftsman 137.219 - page 12

    tNSTALUNG FEED HANDLES (FIG. H) 1_ Thread each feed handle (1) into the threaded holes (2) on the hubassembly (3) andTighten_ Fig.H 4. Unlock the table support lock (4- Fig.D) andswing the table away from the bottom of the chuck. 5. Using a rubber mallet or a hammer and a block of wood, tap the chuck onto the spindle firmly (Fig.K). Fig. K tNSTALUN ...

  • Craftsman 137.219 - page 13

    FENCE ASSEMBLY (FIG. M) 1_ Align the mounting holes of the fence over the table slots. 2. Place a washer (2) on the threaded end of the knob (3). Insert the knob through the mounting hole of the fence and the table slot. 3. Place a washer and wing nut (4) on the knob from under the table. 4. Repeat for the other knob and tighten. Fig. M ADJUSTMENTS ...

  • Craftsman 137.219 - page 14

    [AWARNING I To prevent persona! injury, always disconnect the plug from the power source when making any adjustments. SPINDLE / QUILL (FIG. O) Rotate the feed handles counterclockwise to lower spindle to its lowest position. Hold the chuck and move it front to back. If there is excessive play, proceed with the following adjustments: 1. Loosen the l ...

  • Craftsman 137.219 - page 15

    [AWARNING I AVOID DIRECT EYE CONTACT A Laser light is radiated when the laser guide is turned on. Avoid direct eye contact. Always un=plug the drill press from the power source before making any adjustments. A laser pointer is not a toy and should not come into hands of children. Misuse of this appliance can lead to irreparable eye injuries. Any ad ...

  • Craftsman 137.219 - page 16

    BASmC DRILL PRESS OPERATmONS NOTE: This machine incorporates view windows on the pulley cover used to observe the location of the belL [AWARN NG ! To avoid possible injury, keep guard closed and in place while tool is in operation. SPEEDS AND BELT PLACEMENT (FIG. S) J,AWARNING j ALWAYS lock the switch "OFF" when the drill press is not in ...

  • Craftsman 137.219 - page 17

    Fig.U 1 3 " USING THE FENCE (FIG. V) The fence provides a way of accurately and quickly setting up the workpiece for precision or for repitive drilling operations. 1. Using a centerpunch or sharp nail, make an indentation in the workpiece where you want to dril!. 2. Align the laser lines (x) with the indentation on the workpiece. 3. Loosen the ...

  • Craftsman 137.219 - page 18

    Fig,× 3 5 7 f [AWAR"I"G i To avoid injury from an accidental start, ALWAYS make sure the power switch is in the "OFF" position, the switch key is removed, and the plug is not connected to the power source outlet before removing or installing the chuck. BAS!C OPERATING INSTRUCTIONS To get the best results and minimize the likeli ...

  • Craftsman 137.219 - page 19

    POSITIONING THE TABLE AND WORKPtECE (FIG. AA AND BB) 1. Lock the table (1) to the column (2) at a position so the tip of the drill bit (3) is just above the top of the workpiece (4). 2. ALWAYS place a BACK-UP MATERIAL (scrap wood) on the table beneath the workpiece. This will prevent splintering or heavy burring on the underside of the workpiece. T ...

  • Craftsman 137.219 - page 20

    [AWARNING ] For your own safety, turn the switch OFF and remove the plug from the power source outlet before maintaining or lubricating your dril! press_ Frequently blow out, using an air compressor or dust vacuum, any dust that accumulates inside the motor. Wear protective safety goggles. [AWARNRNG j To avoid shock or fire hazard, Jf the power cor ...

  • Craftsman 137.219 - page 21

    [,&WARNING I To avoid injury from accidental starting, always turn switch OFF and unplug the tool before moving, replacing the blade or making adjustments. , Consult your Sears Service Center if for any reason the motor will not run. PROBLEM POSSIBLE CAUSES REMEDY Noisy operation 1. incorrect belt tension. 1. Adjust tension. See section "A ...

  • Craftsman 137.219 - page 22

    10 in. DRmLL PRESS MODEL NO. 137.219000 [AWARNING I When servicing use only CRAFTSMAN replacement parts. Use of any other parts many create a HAZARD or cause product damage. [,_WARNING I Any attempt to repair or replace electriea! parts on this Drill Press may create a HAZARD unless repair is done by a qualified service technician. Repair service i ...

  • Craftsman 137.219 - page 23

    10 in. DRILL PRESS SCHEMATIC MODEL NO. 137.219000 OJJZ 2C08 2C08 048K 04WG 0KDH 3 _0UGH OVPE 0KSQ 2 o_ 0K7K 048P 048Z OJP44 0KQY2 0L6D 06SV 0KDJ OKFF 2 OKUX 04AD 0KDJ2 04BM 0KC62 OLWC 047X 047U /- ...

  • Craftsman 137.219 - page 24

    Your Home For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and Operator's Manuals that you need to do-itoyourself. For Sears professional installation of home appliances and items like garage ...

Fabricant Craftsman Catégorie Cordless Drill

Les documents que nous recevons du fabricant de l'appareilCraftsman 137.219 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Craftsman
- manuels d’utilisations 137.219
- fiches produit Craftsman
- dépliants
- ou étiquettes-énergie Craftsman 137.219
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Craftsman 137.219.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Craftsman 137.219, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Craftsman 137.219. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Craftsman 137.219.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Craftsman 137.219, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Craftsman 137.219 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Craftsman 137.219.

Le manuel d’utilisation complet Craftsman, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Craftsman 137.219 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Craftsman 137.219, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lCraftsman 137.219 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Craftsman 137.219 - qui devraient nous aider dans les premières étapes lors de l'utilisation Craftsman 137.219
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Craftsman 137.219
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Craftsman 137.219 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Craftsman 137.219?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Craftsman 137.219, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Craftsman 137.219 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)