Français dropdown-ico

Manuel d’utilisation TacT Audio M2150

30 pages 0.14 mb
Télécharger

Aller à la page of 30

Summary
  • TacT Audio M2150 - page 1

    Owner ’ s Manual M2150 / S2150 T rue Digital Amplifier ...

  • TacT Audio M2150 - page 2

    Blank Page ...

  • TacT Audio M2150 - page 3

    3 T act Audio W ARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE T O RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER. NO USER-SER VICEABLE P ARTS INSIDE. REFER SERVICING T O QUALIFIED PERSONNEL. The exclamation point within an equilate ...

  • TacT Audio M2150 - page 4

    CAUTION CAUTION 4 T act Audio 1. Read these instructions entirely before installing or operating this equipment. 2. Keep these instructions. 3. Heed all warnings. 4. Do not use this equipment near water or allow it to become wet. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 6. Do not instal ...

  • TacT Audio M2150 - page 5

    5 T act Audio IMPORT ANT! Please record your serial number here for future reference. Y ou will need this for future upgrades or should you ever require service on your M/S 2150. M/S 2150 serial number: _____________________ Optional modules installed: ADC analog input : __ Registration © 2003 T act Audio Corporation. All right s reserved. No part ...

  • TacT Audio M2150 - page 6

    CAUTION CAUTION 6 T act Audio T able of content s Safety instructions 4 Acknowledgments/Registration 5 Unpacking the m/s 2150 7 Introduction 8 M/S 2150 Connections 9 Front Panel Controls 1 5 Remote Control 1 6 Front Panel Display 1 8 Main screen 1 8 MAIN menu 1 8 Saving Menu Settings 1 8 DELA Y menu 1 9 LEVEL menu 1 9 ADC menu 2 0 CRO menu 2 0 TRIG ...

  • TacT Audio M2150 - page 7

    7 T act Audio Unp acking the M/S 2150 Carefully remove the M/S2150 and accessory kit from the carton and check for shipping damage. Contact both the shipper and T acT Audio immediately if the unit shows any sign of damage from rough handling. All T acT Audio equipment is carefully inspected before leaving our factory . KEEP SHIPPING CAR TON AND P A ...

  • TacT Audio M2150 - page 8

    CAUTION CAUTION 8 T act Audio Introduction - Ultra high precision DA conversion - Upsampling to 384,000 Hz before conversion - Full resolution at -30 dB - Software upgradeable DSP section - DSP-based 48 bit internal electronic crossover (in bi-amped mode) - 192kHz/24bit AD converter - Digital pre-amplification with 24-bit resolution at a playback l ...

  • TacT Audio M2150 - page 9

    9 T act Audio M/S 2150 Connections Digital input The 2150 amplifier has 5 digital inputs: - three RCA (S/PDIF) ( D1, D2, D3) - one AES/EBU (XLR) (D4) - one T osLink (S/PDIF) (D5) All of the digital inputs support PCM audio data with sampling rates from 32kHz to 96kHz /16-24 bits, however , the AES/EBU and RCA/coaxial input s support up to 192kHz. T ...

  • TacT Audio M2150 - page 10

    CAUTION CAUTION 10 T act Audio M/S 2150 Connections Digital output The 2150 amplifier has a digital pass through. The digital input signal is passed to the digital output without processing or volume control. The sampling rate is the native sampling frequency of the input. Digital Output NOTE: that this output is not active when analog input is sel ...

  • TacT Audio M2150 - page 11

    11 T act Audio AC mains input Connect the M/S 2150 to the AC mains wall socket. CAUTION: Use the supplied IEC mains cable, or a 3-prong grounded cable only. Digital Output Speaker output (normal operation) The 2150 amplifier has one pair of high quality WBT speaker terminals. These termi- nals will accept both spade- and banana-plugs. When connecti ...

  • TacT Audio M2150 - page 12

    CAUTION CAUTION 12 T act Audio LOW HIGH RIGHT SPEAKER LEFT SPEAKER + - LOW + - + - HIGH + - Speaker output (Biamped operation) If you are using two or more 2150 amplifiers, and your speakers allow for multi- amping, you can configure the system to run in biamped or even tri-amped mode etc. This type of setup allows for one amplifier channel to driv ...

  • TacT Audio M2150 - page 13

    13 T act Audio LOW HIGH + - LOW + - + - HIGH + - RIGHT SPEAKER LEFT SPEAKER V ertical Biamping HIGH LOW LOW HIGH LEFT SPEAKER RIGHT SPEAKER M/S 2150 Connections ...

  • TacT Audio M2150 - page 14

    CAUTION CAUTION 14 T act Audio Biamping - continued When two or more 2150 amplifiers are configured in a bi-/tri-amped setup, both the signal and the RS232 T acT System Bus must be daisy chained between the amplifi- ers. The same signal flow is applicable for both horizontal and vertical bi-amping. From RCS2.0S, RCS2.2X or TCS mkII *Optional From s ...

  • TacT Audio M2150 - page 15

    15 T act Audio Front Panel Controls ON/OFF Use the “ON/OFF” switch to toggle between ON and OFF operation. (S tandby mode can be only selected only through the remote control) Master volume The master volume is controlled by turning the large volume wheel. The green num- bers on the left side of the wheel will change as you turn the wheel - thi ...

  • TacT Audio M2150 - page 16

    CAUTION CAUTION 16 T act Audio The remote control is used to access the front panel display controls and menus. Remote Control 4 11 2 9 1 3 5 6 7 10 8 12 ...

  • TacT Audio M2150 - page 17

    17 T act Audio 1 - ST ANDBY The ST ANDBY button will turn the M/S 2150 “ ON ” or it will place it into “ ST ANDBY ” mode. When in standby mode, the unit is placed into a low power “idiling” state. The standby button is also used to save changes that were made in the menu editing parameters. By placing the unit into standby the current s ...

  • TacT Audio M2150 - page 18

    CAUTION CAUTION 18 T act Audio Front Panel Display Main screen When the 2150 amplifier is turned ON and the system loading sequence has com- pleted, the amplifier will display the normal operating main screen. INPUT: CD/Transport -17.9 dB Fs= 44.1 3 2 1 1 - Name for input selection 2 - Master level in dB 3 - Input sampling frequency indicator . Mai ...

  • TacT Audio M2150 - page 19

    19 T act Audio . The Delay menu controls the system’s time alignment. The system’s time align- ment can be adjusted by changing the delay time for the left and right outputs inde- pendently . DELA Y menu LEFT RIGHT 0.00 0.00 msec 1 1 - Left and Right channel independent delay time settings. Delay Menu : LEVEL menu LEFT RIGHT 0.0 0.0 dB 1 The Le ...

  • TacT Audio M2150 - page 20

    CAUTION CAUTION 20 T act Audio Front Panel Display CRO menu The M/S 2150 can apply user selectable crossovers to the outputs. The default setting is set to “ OFF ” with no crossovers applied. For your convenience there are a total of 10 default crossover selections pre-loaded for use with most biamped systems. If a different crossover is desire ...

  • TacT Audio M2150 - page 21

    21 T act Audio Front Panel Display TRIG menu The trigger menu is used to control the behavior of the 2150 amplifier when a trigger signal is detected. When the input trigger is set to “ ON ” and a trigger signal is de- tected the amplifier will turn ON. The amplifier will st ay in or switch to “ ST ANDBY ” mode if there is no trigger signal ...

  • TacT Audio M2150 - page 22

    CAUTION CAUTION 22 T act Audio - Max Level controls the system’s maximum signal level. For example: if this option is set to -3.0 dB, the volume control and output can not go above -3.0 dB. - Detection sets the signal detection threshold. If the absolute value of the Left or the Right channel signal goes above this threshold the red signaling dot ...

  • TacT Audio M2150 - page 23

    23 T act Audio INOUT menu This InOut menu is used to set the channel output configuration for the M/S 2150. POL menu (Polarity) OUTPUT: L R SOURCE: L R * InOut Menu : 1 - Source selections for output. 2 - Fixed output speaker posts. 3 - Active source setting. 2 1 3 NOTE: For vertical Biamping, the source menu option should be set to “L”+”L” ...

  • TacT Audio M2150 - page 24

    CAUTION CAUTION 24 T act Audio COMM menu (Communication) REM menu (Remote) The remote menu allows for disabling or enabling the remote control. Once the re- mote control is disabled the unit can only be controlled from the front panel of the unit. An alternate way to enable or disable the remote control is to press the front panel “ ANALOG ” an ...

  • TacT Audio M2150 - page 25

    25 T act Audio ADDR menu (Address) 1 - Address settings. 2 - Active address setting. Address Menu : The address menu allows for the setting of the “address” for the unit. The default address setting is “001”. If multiple amplifiers are used together , different addresses will allow individual control of each amplifier . Use the “ UP ” a ...

  • TacT Audio M2150 - page 26

    CAUTION CAUTION 26 T act Audio The gain menu allows for an increase in the overall volume level of the amplifier . There are four gain settings that are available: 0dB, 6dB, 12dB, and 18dB. 1 - Active gain setting. Gain Menu : 1 Gain 12 dB GAIN menu The amplifier will increase its overall gain by the amount set in the “ Gain ” setting. For exam ...

  • TacT Audio M2150 - page 27

    27 T act Audio The M/S2150 is more than just an amplifier . With powerful features such as level balancing, time alignment, and assignable electronic crossovers, you can custom- ize and build the amplifier system that you need, whether your system is biamped, triamped or more. Each of T act’s amplifiers employ an RS232 in and out connec- tion for ...

  • TacT Audio M2150 - page 28

    CAUTION CAUTION 28 T act Audio Connect your M/S2150 to your Computer Y our M/S2150 must be connected to your computers serial port in order for it to communicate with your computer when you run the M/S2150 software. Please fol- low the steps below to connect your M/S2150 to your computer . 1 - Connect the RS 232 “ Input ” jack on the back of th ...

  • TacT Audio M2150 - page 29

    29 T act Audio Power (RMS. per channel) 8 ohm 2 x 150W Power (RMS. per channel) 4 ohm 2 x 300W Output current (peak, per channel) >50 A Signal-to-noise ratio ( A-weighted) >1 10dB Dynamic range (20 Hz - 20 kHz) >130dB THD+N (all power levels 20Hz-20kHz) <0.01% Digital resolution 16-24 bit Linearity (-120dB) +- 0,2dB Dimensions (WxHxD) 4 ...

  • TacT Audio M2150 - page 30

    T acT Audio, Inc. 201 Gates Road Unit G , Little Ferry – New Jersey 07643, USA Phone: +1 201 440 9300 – Fax: +1 201 440 5580 – Email: info@tactaudio.com www .tactaudio.com ...

Fabricant TacT Audio Catégorie Stereo Amplifier

Les documents que nous recevons du fabricant de l'appareilTacT Audio M2150 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques TacT Audio
- manuels d’utilisations M2150
- fiches produit TacT Audio
- dépliants
- ou étiquettes-énergie TacT Audio M2150
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation TacT Audio M2150.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation TacT Audio M2150, manuels d’entretien, brefs manuels ou manuels de l’utilisateur TacT Audio M2150. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit TacT Audio M2150.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil TacT Audio M2150, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser TacT Audio M2150 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs TacT Audio M2150.

Le manuel d’utilisation complet TacT Audio, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel TacT Audio M2150 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières TacT Audio M2150, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lTacT Audio M2150 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil TacT Audio M2150 - qui devraient nous aider dans les premières étapes lors de l'utilisation TacT Audio M2150
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de TacT Audio M2150
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service TacT Audio M2150 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de TacT Audio M2150?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec TacT Audio M2150, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec TacT Audio M2150 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)