Manuel d’utilisation Genelec 8250A

16 pages 0.84 mb
Télécharger

Aller à la page of 16

Summary
  • Genelec 8250A - page 1

    d s p Operating Manual 8240A and 8250A DSP Loudspeakers ...

  • Genelec 8250A - page 2

    2 ...

  • Genelec 8250A - page 3

    3 INTRODUCTION Congratulations and a thank-you for the purchase of this Genelec 8200 Series DSP Loudspeaker . These systems are designed to integrate easily into the digital production environment. There are several ways to configure and operate the DSP loudspeakers for a wide variety of high quality audio applications. The loudspeakers also have a ...

  • Genelec 8250A - page 4

    4 harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However , there is no guarantee that interference will not occur in a particular installation. If this ...

  • Genelec 8250A - page 5

    5 USING THE 8240A AND 8250A IN ST AND -AL ONE MODE The 8240A and 8250A accept both analogue line level input signals and AES/EBU formatted digital input signals. When the 8240A and 8250A are not connected to Genelec loudspeaker control network, they operate in the stand-alone mode. However , settings made with the Genelec Loudspeaker Manager softwa ...

  • Genelec 8250A - page 6

    6 “DIGIT AL IN AES/EBU” connector Use this female XLR connector for AES/EBU formatted digital audio input signals. This input is selected automatically when a valid digital audio signal is present, and overrides the analogue input. Depending on the digital hardware, transmission of a 192 kHz sample rate is achieved using a double speed, single ...

  • Genelec 8250A - page 7

    7 The overload light (red) is activated by several events, • exceeding the maximum input range of the analog input • exceeding the maximum input range of the digital input with large probability • exceeding the output capacity of the power amplifier (clipping in the power amplifier) and thermal overload of the power amplifier or loudspeaker d ...

  • Genelec 8250A - page 8

    8 Mounting options The vibration insulating Isolation Positioner/Decoupler™ (Iso-P od™) table stand allows tilting of the loudspeaker for correct alignment of the acoustic axis. The stand can be attached to three mounting points allowing vertical and symmetrical horizontal positioning. Genelec 8240A and 8250A can be fitted to König & Meyer ...

  • Genelec 8250A - page 9

    9 This feature is designed to compensate for the boost often occurring at this frequency range when the loudspeaker is placed upon a meter bridge, table or similar reflective surface. T reble Tilt control T reble Tilt control (switches 6 and 7) allows adjusting the treble response above 5 kHz by +2 dB, -2 dB or -4 dB, which can be used for correcti ...

  • Genelec 8250A - page 10

    10 F unctions on Switch Group 2 Stored / Manual Ctrl This allows the selection between two basic methods of controlling the loudspeaker in the stand-alone mode. “MANUAL CTRL ” refers to controlling the loudspeaker using the controls on the loudspeaker’s back panel. The “STORED” refers to using settings stored inside the memory of the loud ...

  • Genelec 8250A - page 11

    11 • Connect the GLM Control Network to the main loudspeakers. • Make a System Setup in GLM. It will consist of main loudspeakers as this is all the network can see, so suitable Rapid Cabling Presets are “Stereo Pair (Analog)” and “5.0 Surround System (Analog)”. • Run AutoCal and review and the results to check for large dips at or ab ...

  • Genelec 8250A - page 12

    12 Guarantee Genelec 8240A and 8250A are supplied with one year guarantee against manufacturing faults or defects that might alter the performance of the loudspeakers. Refer to supplier for full sales and guarantee terms. 8240A Accessories Order code Description 8000-408 Floor stand (K&M 26740-000-58) 8000-401B Wall mount, black (K&M 24180- ...

  • Genelec 8250A - page 13

    13 SPECIFICA TIONS 8240A 8250A Lower cut-off frequency , -3 dB Upper cut-off frequency , -3 dB ≤ 45 Hz ≥ 21 kHz ≤ 35 Hz ≥ 21 kHz F ree field frequency response of system (± 1.0 dB) 48 Hz - 20 kHz 38 Hz - 20 kHz Maximum short term sine wave acoustic output on axis in half space, averaged from 100 Hz to 3 kHz @ 1 m @0.5 m ≥ 105 dB SPL ≥ ...

  • Genelec 8250A - page 14

    14 8240A 8250A Analog audio input connector XLR female, pin 1 gnd, pin 2 +, pin 3 - Analog audio input impedance 10 kOhm balanced Input level for maximum short term output of 100 dB SPL @ 1m Adjustable from +6 to -6 dBu Crossover frequency , Bass/T reble 3.0 kHz 1.8 kHz T reble Tilt control operating range in 2 dB steps +2 to -4 dB & MUTE @ 15 ...

  • Genelec 8250A - page 15

    15 The curves above show the effect of the “Bass Tilt”, “T reble Tilt”, “Desktop Low F requency” and “Bass Roll-Off ” controls on the free field response of the 8240A. The upper curve group shows the horizontal directivity characteristics of the 8240A measured at 1 m. The lower curve shows the system's power response. The upper ...

  • Genelec 8250A - page 16

    Genelec Document D0048R001a. Copyright Genelec Oy 3.2006. All data subject to change ...

Fabricant Genelec Catégorie Portable Speaker

Les documents que nous recevons du fabricant de l'appareilGenelec 8250A peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Genelec
- manuels d’utilisations 8250A
- fiches produit Genelec
- dépliants
- ou étiquettes-énergie Genelec 8250A
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Genelec 8250A.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Genelec 8250A, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Genelec 8250A. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Genelec 8250A.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Genelec 8250A, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Genelec 8250A par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Genelec 8250A.

Le manuel d’utilisation complet Genelec, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Genelec 8250A - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Genelec 8250A, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lGenelec 8250A qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Genelec 8250A - qui devraient nous aider dans les premières étapes lors de l'utilisation Genelec 8250A
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Genelec 8250A
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Genelec 8250A dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Genelec 8250A?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Genelec 8250A, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Genelec 8250A il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (0)