Français dropdown-ico

Manuel d’utilisation CDA EVX100

28 pages Non applicable
Télécharger

Aller à la page of 28

Summary
  • CDA EVX100 - page 1

    Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www .cda.eu evx100 / evx140 Extractor Manual for Installation, Use and Maintenance ...

  • CDA EVX100 - page 2

    2 Important The CD A Group L td cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CD A reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance or use in a commercial environment. This appliance is no ...

  • CDA EVX100 - page 3

    3 IMPORT ANT INFORMA TION FOR CORRECT DISPOSAL OF THE PRODUCT IN A CCORD ANCE WITH EC DIRECTIVE 2002/96/EC. At the end of its working life, the product must be taken to a special local authority waste collection centre or to a dealer providing appliance recycling services. Disposing of a household appliance separately avoids possible negative conse ...

  • CDA EVX100 - page 4

    4 Please note: • Under no circumstances should the extractor be connected to any gas ventilation system, flue system or hot air ducting system. • Do not vent the extractor into an attic or loft space. • Only house the extractor in rooms with adequate ventilation. R emember that the extractor is powerful and whatever air is extracted needs to ...

  • CDA EVX100 - page 5

    5 Using Y our Extractor For best performance, you should switch on the extractor 15 minutes before starting to cook and leave it to run for appro ximately 15 minutes after the end of cooking. T o switch on the extractor and set the speed level - T ouch key “ A ” or press button 1 on the remote. The appliance will switch on at the last speed lev ...

  • CDA EVX100 - page 6

    6 remote control. Whilst the intensive function is active “HI” appears on the centre of the display and the bottom right hand dot flashes once a second. - T o cancel the intensive function, touch key “D” or button 5 again and the extractor will return to the previous speed level. The extractor lights - T o switch the lights on and o , p ...

  • CDA EVX100 - page 7

    7 - T o activate the clean air function, touch key “E” when the appliance is either on or o . When the clean air function is running, “24” will show on the display and a dot will flash in the lower right hand corner of the display when the motor is running. - T o cancel the clean air function, touch any key ex cept the light key . Care ...

  • CDA EVX100 - page 8

    8 T o reset the filter alarm, press button “E” for appro ximately 3 seconds when the extractor is switched o . T o remove the grease filters follow the steps below: 1. Open the stainless steel cover panels by pulling them down and outwards on either side. They will remain located in their hinges. 2. Pull open the handle on each grease fil ...

  • CDA EVX100 - page 9

    9 should remove and replace the charcoal filters. T o attach a new charcoal filter , first open the cover panels and remove the grease filters as described above. Then oer up the charcoal filter to the side of the motor as shown in figure 3 and turn it clockwise until it locks into place. R epeat with the other charcoal filter on the othe ...

  • CDA EVX100 - page 10

    10 R emove the old bulb from the holder . Fit the new bulb, taking care not to touch the glass of the bulb. T ake care to ensure any tools used do not damage the extractor body . Do not touch bulbs or adjacent areas during or straight after prolonged use of the lights. The main extractor light is designed for use during cooking only . The ambient l ...

  • CDA EVX100 - page 11

    11 Installation Positioning the vent outlet: The motor unit can be turned to position the outlet to any of the four sides. 1. Open the decorative cover panel and remove the two grease filters (fig. 5). The decorative cover can be removed, if required, to make the installation easier . T o do this, simply remove the cover fixing screws using an a ...

  • CDA EVX100 - page 12

    12 Installation Installing the extractor: The extractor can be mounted directly into the ceiling, where space between the ceiling and joists permits, or it can be built into a false ceiling. T o install the product, proceed as follows: 1. Mark the ceiling or false ceiling, as appropriate, with centre point of the hob to start the positioning of the ...

  • CDA EVX100 - page 13

    13 4. Drill the dierent holes required for the mounting, as below , using a drill bit suitable for the ceiling material: • The 150mm diameter vent outlet when the ducting will run through the ceiling. • The mains supply chord (10mm minimum). • The four fixing holes for the  10mm nuts and bolts. 5. When the extractor is to be mounted in ...

  • CDA EVX100 - page 14

    14 ceiling, use a sleeve to prevent damage to the plasterboard when the four 10mm nuts and bolts are being tightened. When the ceiling is concrete, use eight diameter symbol 10mm steel rawl bolts. Do not use plastic rawl plugs 6. The motor body incorporates top fixing mounts that can be adjusted by up to 20mm depending on the installation, as show ...

  • CDA EVX100 - page 15

    15 Installation Into a False Ceiling: (T wo persons required) 1. Open the decorative cover panel and remove the two grease filters. 2. R emove the light panels by removing the three screws securing each panel first. Lift the panel and pull towards the centre of the extractor to expose the connections. Carefully disconnect the light connections an ...

  • CDA EVX100 - page 16

    16 fig. 15 3. The extractor is intended to be secured to the ceiling using the four adjustable spring-loaded clips; these are shown in the image below: 4. Before securing the extractor to the ceiling, prepare and connect the ducting as described in the ducting section following the installation information and ensure that the mains electrical supp ...

  • CDA EVX100 - page 17

    17 the adjustment screw to secure the extractor firmly in position Note: When fixing to an 18mm MDF false ceiling, four 2mm spacers have been provided to make the mounts 20mm thick (minimum). If the extractor needs to be removed after installation for any reason, the fixing clips should be slackened and then can be accessed by removing the foil ...

  • CDA EVX100 - page 18

    18 Ducting: The extractor can be used as a recirculation device or as a extraction device, depending on your installation. The hood is more eective when used in the extraction mode (ducted to the outside). When the cooker hood is ducted to the outside, charcoal filters are not required. The ducting used must be 150mm (6 Inches), rigid circular ...

  • CDA EVX100 - page 19

    19 R e-Circulation: An internal air vent is required, as shown below . This ensures that the air is placed back in the kitchen after it has been filtered Fit the charcoal filters to the body of the motor as shown in the maintenance section of the manual. Extraction: The extractor is provided with a non-return butterfly valve which should be fit ...

  • CDA EVX100 - page 20

    20 Adjusting the P osition of the Decorative Cover P anel: The decorative panel can be finely adjusted by moving the positions of the cover hinges, as shown here. Use a suitable allen key or small hex driver (3mm) to slacken the cover adjusting screws before sliding the cover into the correct position. When done, re-tighten the fixing screws. fi ...

  • CDA EVX100 - page 21

    21 T ypical Installation Examples: ...

  • CDA EVX100 - page 22

    22 Changing the Light IMPORT ANT : DO NO T PERFORM MAINTENANCE OR A TTEMPT T O CLEAN THE EXTRA CTOR WITHOUT FIRS T SWITCHING OFF THE ELECTRICITY SUPPL Y . DO NO T CHANGE THE LIGHT BULB IMMEDIA TEL Y AFTER USE AS THE BULB WILL BE HO T . ALL OW T O COOL BEFORE REMOVING. 1. Unfasten the sliding brackets on either side of the cover panel and the cover ...

  • CDA EVX100 - page 23

    23 Synchronising the remote control with the extractor When the extractor is o , press and hold button “B” , and then switch the extractor on. After five seconds release button “B” and the display will light up in sections. Then press button “E” . “T C” will flash twice to confirm the remote is synchronised. “T C” will fl ...

  • CDA EVX100 - page 24

    24 Mains Electricity Connection THIS APPLIANCE MUST BE CONNECTED T O THE MAINS SUPPL Y BY A COMPETENT PERSON, USING FIXED WIRING VIA A DOUBLE POLE SWIT CHED FUSE SPUR OUTLET AND PRO TECTED BY A 3A FUSE. W arning! This appliance must be earthed W e recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E. ...

  • CDA EVX100 - page 25

    25 • The wire which is coloured brown must be connected to the terminal marked L (Live), or coloured red. Note: Use a 3A Fuse Assembly and electrical connection should be carried out by specialised personnel. When installing this product we recommend you seek the help of another individual. The mains isolation switch should be readily accessible ...

  • CDA EVX100 - page 26

    26 Electrical Information Mains electrical voltage: 230 – 240V ac. T otal rated power consumption evx100 / evx140: 410W . T roubleshooting Please note: Y our extractor is equipped with a motor protection device that will switch o the motor to prevent damage from overheating. This may happen during cooking when most or all of the zones/ burners ...

  • CDA EVX100 - page 27

    27 Attribute Symbol Value Units Model Identification evx100/140 Annual Energy Consumption AEC Hood 201.7 kWh Time increase factor f 1.0 Fluid Dynamic Efficiency FDE Hood 18.8 (C) Energy Efficiency Index EEI Hood 98.1 Measured airflow at Best Efficiency Point Q BEP 394.0 m 3 /h Measured Pressure at Best Efficiency Point P BEP 254.0 Pa Maximum airflo ...

  • CDA EVX100 - page 28

    Please contact our Customer Care Department for Service on the details below . Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer .care@cda.eu W : www. cda.eu ...

Fabricant CDA Catégorie Exhaust hood

Les documents que nous recevons du fabricant de l'appareilCDA EVX100 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques CDA
- manuels d’utilisations EVX100
- fiches produit CDA
- dépliants
- ou étiquettes-énergie CDA EVX100
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation CDA EVX100.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation CDA EVX100, manuels d’entretien, brefs manuels ou manuels de l’utilisateur CDA EVX100. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit CDA EVX100.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil CDA EVX100, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser CDA EVX100 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs CDA EVX100.

Le manuel d’utilisation complet CDA, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel CDA EVX100 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières CDA EVX100, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lCDA EVX100 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil CDA EVX100 - qui devraient nous aider dans les premières étapes lors de l'utilisation CDA EVX100
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de CDA EVX100
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service CDA EVX100 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de CDA EVX100?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec CDA EVX100, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec CDA EVX100 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)