Français dropdown-ico

Manuel d’utilisation Jet Tools J-7060

28 pages 0.57 mb
Télécharger

Aller à la page of 28

Summary
  • Jet Tools J-7060 - page 1

    Operating Instructions and Part s Manual 20-Inch x 20-Inch Semi Automatic Horizont al Cut-Off Band Saw Model: J-7060 WHM TOOL G ROUP , Inc. 427 New Sanford Road LaV ergne, T ennessee 30786 Part No. M-414476 Ph.: 800-274-6848 Revision A2 03/09 www .wmhtoolgroup.com Copyright © 2009 WMH T ool Group, Inc. ...

  • Jet Tools J-7060 - page 2

    W arranty and Service WMH T ool Group, Inc., warrants every product it sells. If one of our tools needs service or rep air , one of our Authorized Service Centers located throughout the United S tates can give you quick service. In most cases, any of these WMH T ool Group Authorized Service Centers can authorize warranty repair , assist you in obta ...

  • Jet Tools J-7060 - page 3

    3 T able of Content s Cover Page ..................................................................................................................... ...... 1 General Specifications ......................................................................................................... .4 Operating Precautions .................................... ...

  • Jet Tools J-7060 - page 4

    4 General Specifications The JET J-7060 Semi-Automatic Horizontal Cut-Off Band Saw incorporates a number of exclusive design features and innovations to make this saw a powerful and productive addition to machine shops, mainte- nance shops, tool rooms, and fabrication and welding shops. The exclusive swivel control panel allows the operator access ...

  • Jet Tools J-7060 - page 5

    5 - Always follow instructions in Operating Instruc- tions and Parts Manual when changing acces- sory tools or parts. - Never modify the machine without consulting JET Corporation. Y ou - the Stationary Power T ool User - Hold the Key to Safety . Read and follow these simple rules for best results and full benefits from your machine. Used properly ...

  • Jet Tools J-7060 - page 6

    6 from the work area. Make the workshop com- pletely safe by using padlocks, master switches, or by removing starter keys. Conductor Length A WG (American Wire Gauge) Number 240 V olt Lines 120 V olt Lines 0 - 50 Feet No. 14 No. 14 50 - 100 Feet No. 14 No. 12 Over 100 Feet No. 12 No. 8 Safety Instructions on Sawing Systems B C D 8. Bring adjustable ...

  • Jet Tools J-7060 - page 7

    7 0 0 9 8 7 6 5 4 3 2 1 10 Operating Instructions Controls The operating controls for the saw are provided in a control panel on the left side of the machine. The control panel is mounted on a pivoting tube. The pivoting tube allows the operator to position the control panel in a convenient location. Introduction This manual includes operating and ...

  • Jet Tools J-7060 - page 8

    8 ( F T ) 1 2 1 1 1 0 9 8 7 6 5 4 3 2 1 0 The bottom row of controls include the following: 1. Stop pushbutton is used to stop the saw blade drive motor . 2. Emergency stop pushbutton is used to quickly disconnect electrical power to the machine. 3. Coolant On/Off selector switch is used to start and stop the coolant pump motor . Other Controls Ref ...

  • Jet Tools J-7060 - page 9

    9 Evaluating Cutting Efficiency Is the blade cutting efficiently? The best way to determine this is to observe the chips formed by the cutting blade. If the chip formation is powdery , then the feed rate is much too light, or the blade is dull. If the chips formed are curled, but colored — that is, either blue or straw-colored from heat generated ...

  • Jet Tools J-7060 - page 10

    10 W ork Set-up Securing the Workpiece for Square Cuts (see figure 5) 1. Raise the saw head. 2. Slide the left vise jaw far enough to the left to allow the workpiece to be placed in the vise. 3. Place the workpiece on the work table. If the workpiece is long, provide support at the other end. It may also be necessary to provide addi- tional downwar ...

  • Jet Tools J-7060 - page 11

    11 rod. Position the stop post against the work piece and tighten the knob in the stop L-bracket. The stop post can be moved left or right as required to place the stop post against the work piece. Figure 9: Placing workpieces in the vise ff f f f Rounds Flats/strips Channels Angles Squares/rectangles I-Beams Hexagonals T ees Knock off sharp edge h ...

  • Jet Tools J-7060 - page 12

    12 Figure 10: Blade tracking and tensioning Blade Tracking Hex Adjustment Screws Center Locking Screws Single Adjustment Screw screws.) Factory or Field Procedure 1. Raise the saw head enough to allow the saw motor to operate. 2. Loosen four knobs securing the blade cover . Lift the cover and swing it backward. 3. Remove the blade guard mounted on ...

  • Jet Tools J-7060 - page 13

    13 Blade Guide Bearing Adjustment Proper adjustment of the blade guide bearings is critical to efficient operation of the cut-of f saw . The blade guide bearings are adjusted at the Factory . They should rarely require adjustment. When adjustment is required, adjust immediately . Failure to maintain proper blade adjustment may cause serious blade d ...

  • Jet Tools J-7060 - page 14

    14 T est cuts can be used to determine whether or not you have adjusted the blade accurately . Use 2-inch round bar stock to perform these test cuts, as follows: 1. With the bar stock securely clamped in the vise, make a cut through the bar stock. (See figure 14.) 2. Mark the top of the bar stock. 3. Move the bar stock about 1/4-inch past the blade ...

  • Jet Tools J-7060 - page 15

    15 Changing Blades W ARNING: SHUT OFF ALL ELECTRICAL POWER TO THE MACHINE. 1. Loosen four knobs securing the blade cover . Lift the cover and swing it backward. 2. Remove the blade guard mounted to the left blade guide support. W ARNING: AL W A YS WEAR LEA THER GLOVES WHEN HANDLING SA W BLADE TO A VOID INJURY Servicing Hydraulic Oil W ARNING: SHUT ...

  • Jet Tools J-7060 - page 16

    16 1. Loosen the knob on the blade guide support and slide the guide left or right as required. Repeat for the other blade guide. 2. Set the blade guide supports as required to accommodate the width/diameter of the workpiece. The blade guides should be posi- tioned so the guides do not contact the workpiece as the saw head moves downward through th ...

  • Jet Tools J-7060 - page 17

    17 2. Remove the attaching screw , spring washer and washer . Remove and discard the brush (see figure 20). 3. Install replacement brush and secure with screw , spring washer and washer . 4. Close the blade cover and secure with four knobs. Replacement of Guide Bearings (see figure 19) 1. Remove the cap screw from the blade guide bearing. Separate ...

  • Jet Tools J-7060 - page 18

    18 Uncrating and S potting S pot the saw where it makes the most sense for the operations you will probably be doing. If you are going to be doing cut-off work on very long pieces of stock, allow plenty of room for the stock, and the infeed and outfeed supports. Remove the saw from the shipping skid and discard any hold-down devices that were used ...

  • Jet Tools J-7060 - page 19

    19 Wiring Diagram ...

  • Jet Tools J-7060 - page 20

    20 T roubleshooting Fault Excessive blade breakage Premature blade dulling Bad cuts (out-of-square) Bad cuts (rough) Probable cause 1. Material loose in vise. 2. Incorrect speed or feed. 3. T eeth too coarse for material. 4. Incorrect blade tension. 5. Saw blade is in contact with workpiece before the saw is started. 6. Blade rubs on the wheel flan ...

  • Jet Tools J-7060 - page 21

    21 1. Blade is binding in the cut. 2. Blade tension too high. 1. Blade guides worn 2. Blade guide bearings not adjusted. 3. Blade guide bearing bracket is loose. 1. Blade tooth pitch too coarse for workpiece. 2. Feed too slow; feed too fast. 3. Workpiece vibrating. 4. Gullets loading up with chips. 1. Blade tension too high. 2. Drive belt tension t ...

  • Jet Tools J-7060 - page 22

    22 Replacement Parts This section provides exploded view illustrations that show the replacement parts for the Model J-7060 12-Inch x 20-Inch Semi-Automatic Horizontal Cut-Of f Band Saw . Also provided are parts listings that provide p art number and description. The item numbers shown on the illustration relate to the item number in the facing par ...

  • Jet Tools J-7060 - page 23

    23 Exploded View – Saw Base - Model J-7060 Semi-Automatic Cut-Off Band Saw 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 ...

  • Jet Tools J-7060 - page 24

    24 Parts List – Saw Base - Model J-7060 Semi-Automatic Cut-Off Band Saw Re f Part No . Number Description Qty 1 5512120 Bolt, Hex Cap (M12X35) 1 2 5512121 W asher , Lock (M12) 1 3 5512122 Pin 2 4 J-5512123 Rack 1 5 J-5512124 Bracket, Slide 1 6 J-5512125 Bl o ck, Rack 1 7 5512126 Screw , Set (M6X10) 1 8 J-5512127 Ja w , V ise (Left) 1 9 5512128 W ...

  • Jet Tools J-7060 - page 25

    25 Part s List – Saw Base - Model J-7060 Semi-Automatic Cut-Off Band Saw , (Continued) Re f Part No . Number Description Qty 120 5512222 Screw , Pan Head (M6X15) 4 121 5512223 V alve, Relief 1 12 2 J-5512224 Plate, Cover 1 12 3 J-5512225 Box, S tationary 1 124 5512226 Screw (M8X16) 4 12 5 J-5512227 Plate, Sole 1 126 5512228 Screw (1/4X5/8 In.) 2 ...

  • Jet Tools J-7060 - page 26

    26 Exploded View – Saw Head - Model J-7060 Semi-Automatic Cut-Off Band Saw 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 190 191 192 194 193 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 21 1 212 213 214 215 216 ...

  • Jet Tools J-7060 - page 27

    27 Parts List – Saw Head - Model J-7060 Semi-Automatic Cut-Off Band Saw Re f Part No . Number Description Qty 146 5512248 Bearing, Thrust (51 194NJK) 1 147 5512249 Indicator , T ension 1 148 5512250 W asher , Flat 1 149 5512251 W asher , S pecial Spring 1 8 15 0 J-5512252 Bracket, Slide 1 151 5512253 W asher , Lock 3 152 5512254 Screw , Hex Cap 3 ...

  • Jet Tools J-7060 - page 28

    WMH T ool Group 427 New Sanford Road LaV ergne, T ennessee 30786 Ph: 800-274-6848 www .wmhtoolgroup.com ...

Fabricant Jet Tools Catégorie Saw

Les documents que nous recevons du fabricant de l'appareilJet Tools J-7060 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Jet Tools
- manuels d’utilisations J-7060
- fiches produit Jet Tools
- dépliants
- ou étiquettes-énergie Jet Tools J-7060
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Jet Tools J-7060.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Jet Tools J-7060, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Jet Tools J-7060. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Jet Tools J-7060.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Jet Tools J-7060, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Jet Tools J-7060 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Jet Tools J-7060.

Le manuel d’utilisation complet Jet Tools, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Jet Tools J-7060 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Jet Tools J-7060, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lJet Tools J-7060 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Jet Tools J-7060 - qui devraient nous aider dans les premières étapes lors de l'utilisation Jet Tools J-7060
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Jet Tools J-7060
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Jet Tools J-7060 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Jet Tools J-7060?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Jet Tools J-7060, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Jet Tools J-7060 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)