Français dropdown-ico

Manuel d’utilisation Sanyo VQM-801P

34 pages 0.72 mb
Télécharger

Aller à la page of 34

Summary
  • Sanyo VQM-801P - page 1

    INSTRUCTION MANUAL VQC-801P VQM-801P Qua d Co mp ressor Engl ish GB Qua d Co mp ressor Deutsch D Compre sseur quadrupl ex Français F Co mp re sor cu ádr up le Espa ñol E Compre ssore per quadranti It ali ano I Ab out t his m anua l • Be fore inst all ing a nd us in g this unit , p lea se re ad this manu al carefull y . Be s ure to keep it hand ...

  • Sanyo VQM-801P - page 2

    PRECAUTION WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR OTHER MOISTURE. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. If the power supply cord (AC power cord) of this appliance is damaged, it must be replaced. Return to a SANYO Authorised Service Ce ...

  • Sanyo VQM-801P - page 3

    CONTENTS PARTS NAMES . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 FRONT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 REAR PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 RECORDING LIVE PICTURES IN QUAD SCREEN DISPLAY MODE ONLY CO ...

  • Sanyo VQM-801P - page 4

    PARTS NAMES FRONT PANEL This unit is not equipped with a power switch. The power is turned on/off when the supplied power cord is connected/disconnecte d at the power source. 1 POWER indicator 2 Camera select buttons and camera indicators Use these buttons to select the picture from the corresponding camera. When a camera is selected, the correspon ...

  • Sanyo VQM-801P - page 5

    PARTS NAMES REAR PANEL 1 CAMERA input terminals (1 – 8) 2 VCR IN (Video cassette recorder input) terminal 3 VCR OUT QUAD FULL (Video signal output) terminal Output in quad screen and full screen display modes. 4 VCR OUT QUAD ONLY (Video signal output) terminal Output only in quad screen display mode. However, the output display mode at this termi ...

  • Sanyo VQM-801P - page 6

    CONNECTION Before making any connection, make sure all the devices are turned off. Before making the connections, please refer to the instruction manual accompanying each device. If the devices are not connected properly, that may cause a fire and/or damages. RECORDING LIVE PICTURES IN QUAD SCREEN DISPLAY MODE ONLY CONNECTIONS NOTE: With model VQM- ...

  • Sanyo VQM-801P - page 7

    CONNECTION REMOTE CONTROLLER CIRCUIT CONNECTIONS Use the layout below to make a remote controller and make the connections to the remote input pins (RC, C) of the CONTROL terminal as indicated. This will permit remote controlled operation of this unit. (make contact LOW input) INSTALLING THE RACK MOUNTING BRACKETS (SOLD SEPARATELY) To mount this un ...

  • Sanyo VQM-801P - page 8

    BASIC OPERATIONS MODE SWITCHING When the unit is connected to a power source, the default display mode will be: live picture from the four cameras 1 – 4 in a quad screen. You can use the VCR, LIVE and MENU buttons to switch to the desired mode (see below for further information). LIVE picture mode VCR playback mode LIVE picture mode Menu mode Pow ...

  • Sanyo VQM-801P - page 9

    BASIC OPERATIONS SECURITY LOCK FUNCTION This function lets you lock the camera live picture mode or VCR playback mode, so that it cannot be switched to another mode. Security lock Press the LIVE or the VCR button for about 3 seconds. The buzzer will be heard and all the buttons will be locked. If a button is pressed by mistake, the buzzer is heard ...

  • Sanyo VQM-801P - page 10

    LIVE PICTURE MODE (VIDEO OUT QUADFULL) Operations with the monitor connected to the VIDEO OUT QUADFULL terminal. Press the LIVE button. The live pictures from the cameras connected to the CAMERA terminals (1 – 4) on the unit back panel will be displayed. Refer to the diagrams below for the buttons to press in order to select the desired operation ...

  • Sanyo VQM-801P - page 11

    QUAD SCREEN OPERATIONS (Live picture) Press the QUAD button once. The camera select indicators (1 – 4) light and quad screen A is displayed. Press the QUAD button one more time to switch to quad screen B. NOTE: The quad screen (A or B) last selected is memorised and will be selected first when switching to quad screen mode again. Sequential displ ...

  • Sanyo VQM-801P - page 12

    QUAD SCREEN OPERATIONS (Live picture) Example: To freeze the image from camera 4 1 Press the STILL button. The STILL indicator flashes and the still image display mode is selected. 2 Press the camera select 4 button. The camera 4 indicator flashes, the image from camera 4 is frozen, and “ S ” flashes on-screen. ☞ To cancel the still image dis ...

  • Sanyo VQM-801P - page 13

    QUAD SCREEN OPERATIONS (Live picture) (The zoomed in area is set by the frame position.) • c button: will move the frame to the right • l button: will move the frame down Example: To zoom in the image from camera 4 and set the zoom range You can select the portion of the image to zoom in. The default zoomed in area is the centre of the image, b ...

  • Sanyo VQM-801P - page 14

    FULL SCREEN OPERATIONS (Live picture) Press a camera select (1 – 8) button. The camera select indicator lights and the live picture from the corresponding camera is displayed full screen. NOTE: In full screen mode, still and zoomed in image display modes are not possible. Sequential display of each camera pictures at 1 second interval Press the S ...

  • Sanyo VQM-801P - page 15

    VCR PLAYBACK MODE (VIDEO OUT QUADFULL) Operations with the monitor connected to the VIDEO OUT QUADFULL terminal. Press the VCR button. The VCR playback mode is selected. When a tape is played back, the recording of the live pictures will be displayed on the monitor. Refer to the diagrams below for the buttons to press in order to select the desired ...

  • Sanyo VQM-801P - page 16

    MENU SETTING MODE MENUS DISPLAYS To display the menus, press the MENU button. Menu 1 Menu 2 Menu 3 Menu 4 Menu 5 Menu 6 (CLOCK SET) 01-01-2000 SAT 00:00:00 (SUMMER TIME SET) MODE NO USE WEEK MON TIME ON LST-SUN 03 02:00 OFF LST-SUN 10 02:00 (TITLE SET) TITLE 1 ---------1 2 ---------2 3 ---------3 4 ---------4 5 ---------5 6 ---------6 7 ---------7 ...

  • Sanyo VQM-801P - page 17

    LANGUAGE SETTING Menu 1 (LANGUAGE/LANG./SPRACHE) The default menu language is English. The available language settings are English, French and German. Setting the language 1 Press the MENU button once to display the (LANGUAGE/LANG./SPRACHE) menu. 2 Press the l button to highlight the desired language. 3 ☞ Press the MENU button to go to the next m ...

  • Sanyo VQM-801P - page 18

    CLOCK AND SUMMER TIME SETTING Menu 2 (CLOCK SET) The default setting is as indicated below. The clock will start after the actual time and date are set and the operations under (SUMMER TIME SET) are completed. Default clock settings: 01:01:2000 SAT 00:00:00 (January 1, 2000 at 00:00) 1 Press the MENU button twice to display the (CLOCK SET) menu. 2 ...

  • Sanyo VQM-801P - page 19

    CAMERA TITLE SETTING Menu 3 When a picture from a camera is displayed on-screen the camera number (1 to 8) is displayed at the bottom of the image. You can enter a camera title, such as the camera location (up to 10 characters), that will be displayed instead of the camera number. (TITLE SET) 1 Press the MENU button 3 times to display the (TITLE SE ...

  • Sanyo VQM-801P - page 20

    ALARM SETTING Menu 4 When an alarm trigger is received from sensors such as a door bell, movement sensor, etc. you can set the display mode and the recording mode for the pictures from the concerned camera. (ALARM SET) Changing the Settings 1 Press the MENU button 4 times to display the (ALARM SET) menu. 2 Press the l button to highlight the settin ...

  • Sanyo VQM-801P - page 21

    VIDEO SENSOR SETTING Menu 5 You can set an area of the image on the screen to be used as a video sensor ( ). The video sensor detects movement in the selected area of the image and sends an alarm trigger that will initiate priority recording of the images from the concerned camera. (VIDEO SENSOR SET) SETTING THE VIDEO SENSOR POSITION AND SENSITIVIT ...

  • Sanyo VQM-801P - page 22

    TIMER SETTING Menu 6 The timer can be set to record during the daytime and/or nighttime. According to the timer settings, each camera picture full screen display switching speed can be set, and the cameras to be displayed in the quad screens can be selected. (TIMER SET) 1 Press the MENU button 6 times to display the (TIMER SET) menu. 2 Set the dayt ...

  • Sanyo VQM-801P - page 23

    CLOCK, TITLE DISPLAY AND MONITOR SETTINGS Menu 7 (DISPLAY SET) The clock and the camera title settings entered in the menus (CLOCK SET) and (TITLE SET) can be displayed on-screen. SETTING THE CAMERA TITLE AND THE CLOCK DISPLAY POSITION (POSITION SET) 1 Press the MENU button 7 times to display the (DISPLAY SET) menu. 2 Using the + (or – ) button, ...

  • Sanyo VQM-801P - page 24

    CLOCK, TITLE DISPLAY AND MONITOR SETTINGS Menu 7 Display when no switching signal input is present (Table 1) (MENITOR SET) menu QUADONLY ← QUADFULL setting N (normal setting) Y Quad screen A or B display Image output at the VIDEO OUT terminal QUAD ONLY • Either setting ( Y or N ) Quad screen A or B (manual switching possible) QUAD FULL • Eith ...

  • Sanyo VQM-801P - page 25

    CLOCK, TITLE DISPLAY AND MONITOR SETTINGS Menu 7 Display when a switching signal input is present (Table 2) (MONITOR SET) menu QUADONLY ← QUADFULL setting N (normal setting) Y Quad screen A or B display Image output at the VIDEO OUT terminal QUAD ONLY • Either setting ( Y or N ) Quad screen A or B (manual switching possible) QUAD FULL • Eithe ...

  • Sanyo VQM-801P - page 26

    VIDEO LOSS SETTING AND COMPUTER CONTROL SETTING Menu 8 (VIDEO LOSS SET) When the live picture signal feed is interrupted, you can set the action taken, and if the video loss is recorded as alarm data. This function will only operate in quad screen display, to select it, set “ VIDEO LOSS ” to “ ON ” . Setting the Video Loss Mode 1 Press the ...

  • Sanyo VQM-801P - page 27

    ALARM DATA DISPLAY Menu 9 According to the settings entered in the (ALARM SET), (VIDEO SENSOR SET) and (VIDEO LOSS SET) menus, information about the alarms (alarm data) can be recorded. Up to 100 alarm data entries can be displayed on-screen (on up to 13 screens). (ALARM DATA) Displaying the Alarm Data 1 Press the MENU button 9 times to display the ...

  • Sanyo VQM-801P - page 28

    ALARMS OPERATIONS There are three types of alarms; the alarms set by an external alarm trigger, the alarms set by a loss of the video signal and the alarms set by the video sensor. EXTERNAL ALARMS When external inputs such as a door bell, an interphone, etc., are connected to the CONTROL terminal (pins 1 – 8), they will send alarm triggers automa ...

  • Sanyo VQM-801P - page 29

    RS232C CONTROL CONNECTION Connect a 9-pin D-SUB cable (sold separately) from the RS232C terminal on the rear panel to the computer serial connector. Setting the Data Transmission Speed After the connection is made, set the data transmission speed in the (RS232C SET) menu (see page 25 ). INTERFACE SPECIFICATIONS For the RS232C terminal specification ...

  • Sanyo VQM-801P - page 30

    RS232C CONTROL INFORMATION GATHERING COMMANDS STATUS SENSE(D7) When this command is sent from the computer, this unit will send a 5-byte response (see Table 1 ). STATUS SENSE(D7) byte assignment (Table 1) The third, fourth and fifth bytes are reserved. First byte Bit Bit state information 7 LIVE/VCR indication 0: LIVE picture mode 1: VCR playback m ...

  • Sanyo VQM-801P - page 31

    RS232C CONTROL COMMANDS AVAILABLE FROM THE QUAD COMPRESSOR ACK(0A) Response when this unit receives a command. NAK(0B) Response if this unit did not receive the command. ALARM(BF) When there is an alarm, this command is sent as header. Then, the alarm information is sent in a 1-byte transmission (see Table 3 ). ALARM information (Table 3) Bit Bit s ...

  • Sanyo VQM-801P - page 32

    RS232C CONTROL COMMAND TABLE (TABLE 4) The commands available are indicated in the table. If a function is not available on the unit, the command will not operate even if sent. 0 1 2 3 45 6 7 89 0 0 ENTER LIVE FULL 1 11 VCR PB FULL 2 2 2 (VERSION) (MULTI) FULL 3 33 ( » ) « (SHIFT) QUAD FULL 4 44 ( 1 ) O MENU (PLUS) FULL 5 55 + NEXT ZOOM FULL 6 6 ...

  • Sanyo VQM-801P - page 33

    SPECIFICATIONS Signal format : Based on PAL colour signal standard (VQC-801P) Based on PAL B/W signal standard (VQM-801P) Camera signal input synchronization : Asynchronous Camera input terminals (CAMERA) : VS/VBS, 1.0 Vp-p/75 Ω , BNC connector x 8 VCR input terminal (VCR IN) : Composite input, VS/VBS, 1.0 Vp-p/75 Ω , BNC connector x 1 VIDEO ou ...

  • Sanyo VQM-801P - page 34

    SANYO Electri c Co., Ltd. 1AC6 P1P2 09 2-- L8Q R5, L8 QS5/ XE (07 99K P-N I01 ) Pr int ed i n Japa n L8QR5/XE (VQC-801P , VQM-801P GB) 1999. 12. 2 ...

Fabricant Sanyo Catégorie Security Camera

Les documents que nous recevons du fabricant de l'appareilSanyo VQM-801P peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Sanyo
- manuels d’utilisations VQM-801P
- fiches produit Sanyo
- dépliants
- ou étiquettes-énergie Sanyo VQM-801P
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Sanyo VQM-801P.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Sanyo VQM-801P, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Sanyo VQM-801P. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Sanyo VQM-801P.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Sanyo VQM-801P, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Sanyo VQM-801P par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Sanyo VQM-801P.

Le manuel d’utilisation complet Sanyo, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Sanyo VQM-801P - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Sanyo VQM-801P, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lSanyo VQM-801P qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Sanyo VQM-801P - qui devraient nous aider dans les premières étapes lors de l'utilisation Sanyo VQM-801P
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Sanyo VQM-801P
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Sanyo VQM-801P dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Sanyo VQM-801P?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Sanyo VQM-801P, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Sanyo VQM-801P il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)