Français dropdown-ico

Manuel d’utilisation Zenoah G455AVS

30 pages 0.36 mb
Télécharger

Aller à la page of 30

Summary
  • Zenoah G455AVS - page 1

    The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. WARNING OWNER / OPERA T OR MANUAL CHAINSA WS 2812-93112 (901) G455A VS  IMPORTANT: Before operating your RedMax product, read this manual carefully and completely. ...

  • Zenoah G455AVS - page 2

    ...

  • Zenoah G455AVS - page 3

    Thank you for choosing our RedMax® chain saw . This manual will provide you with full understanding of the necessary instructions for assembly , operation and maintenance of the equipment. Please read it carefully before starting operation. For continued safe and reliable operation, use ONL Y original RedMax parts and accessories, Adhere to all no ...

  • Zenoah G455AVS - page 4

    1. For Safe Operation 2 1. Never operate a chain saw when you are fatigued, ill, or upset, or under the influence of medication that may make you drowsy, or if you are under the influence of alcohol or drugs. 2. Use safety footwear, snug fitting clothing and eye, hearing and head protection devices. 3. Always use caution when handling fuel. Wipe up ...

  • Zenoah G455AVS - page 5

    3 1 6 . Operate the chain saw only in well ventilated areas. Never start or run the engine inside a closed room or building. Exhaust fumes contain dangerous carbon monoxide. 1 7 . Do not operate a chain saw in a tree unless specially trained to do so. 18. Guard against kickback. Kickback is the upward motion of the guide bar which occurs when the s ...

  • Zenoah G455AVS - page 6

    The saw chain has very sharp edges. Use thick protective gloves for safety. 1. Loosen the nuts and remove the chain cover. 2. Install the attached spike to the power unit. 3. Gear the chain to the sprocket and, while fitting the saw chain around the guide bar, mount the guide bar to the power unit, Then adjust the position of chain tensioner nut on ...

  • Zenoah G455AVS - page 7

    ■ FUEL The RedMax engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use. If RedMax oil is not available, use an anti-oxidant added quality oil expressly labeled for air-cooled 2-cycle engine use. RECOMMENDED MIXING RATIO GASOLINE 32 : OIL 1 Exhaust emission are controlled by the fundamental engine parameter ...

  • Zenoah G455AVS - page 8

    Starting engine 1 . Fill fuel and chain oil tanks respectively, and tighten the caps securely. 2. Tilt the switch lever upward. 3. While holding the throttle lever together with the throttle interlock, push in the side latch and release the throttle lever to hold it at the starting position. 4. Pull out the choke knob to the closed position. Note: ...

  • Zenoah G455AVS - page 9

    5 . While holding the saw unit securely on the ground, pull the starter rope vigorously. Do not start the engine while hanging the chain saw with a hand. The saw chain may touch your body. It's very dangerous. 6. When engine has ignited first, push in the choke knob and pull the starter again to start the engine. 7 . Allow the engine to warm u ...

  • Zenoah G455AVS - page 10

    1. H and L needles are restricted within the number of turn as shown below, because this engine conforms to 1995 California regulations for utility and lawn and garden equipment engines as applicable. H needle: 1 / 4 L needle: fixed 2 . Start engine and allow it to warm up in low speed for a few minutes. 3. Turn idle adjusting screw (T) countercloc ...

  • Zenoah G455AVS - page 11

    Chain brake This machine is equipped with an automatic brake to stop saw chain rotation upon occurrence of kickback while in saw cutting operation. The brake is automatically operated by inertial force which acts on the weight fitted inside the front gurd. This brake can also be operated manually with the front guard turned down to the guide bar. T ...

  • Zenoah G455AVS - page 12

    NOTE: • Before proceeding to your job, read “For Safe Operation” section. It is recommended to first practice sawing easy logs. This also helps you get accustomed to your unit. • It is not necessary to force the saw into the cut. Apply only light pressure while running the engine at full throttle. • Racing the engine with the chain seized ...

  • Zenoah G455AVS - page 13

    1. Decide the felling direction considering the wind, Iean of the tree, location of heavy branches, ease of job after felling, and other factors . 2. While clearing the area around the tree, arrange a good foothold and retreat path. 3. Make a notch cut one-third of the way into the tree on the felling side. 4. Make a felling cut from the opposite s ...

  • Zenoah G455AVS - page 14

    6. Maintenace Before cleaning, inspecting or repairing your unit, make sure that engine has stopped and is cool. Disconnect the spark plug to prevent accidental starting. A. Maintenance after each use 1. Air filter Dust on the cleaner surface can be removed by tapping a corner of the cleaner against a hard surface. To clean dirt in the meshes, spli ...

  • Zenoah G455AVS - page 15

    B. Periodical service points 1. Cylinder fins Dust clogging between the cylinder fins will cause overheating of the engine. Periodically check and clean the cylinder fins after removing the air cleaner and the cylinder cover. When installing the cylinder cover, make sure that switch wires and grommets are positioned correctly in place. 2. Fuel filt ...

  • Zenoah G455AVS - page 16

    A. Saw Chain It is very important for smooth and safe operation to keep the cutters always sharp. Your cutters need to be sharpened when: • Sawdust becomes powder-like. • You need extra force to saw in. • The cut way does not go straight. • Vibration increases. • Fuel consumption increases. Cutter setting standards: Be sure to wear safety ...

  • Zenoah G455AVS - page 17

    After every cutter has been set, check the depth gauge and file it to the proper level as illustrated. Be sure to round off the front edge to reduce the chance of kickback or tie-strap breakage. Make sure every cutter has the same length and edge angles as shown below. 15 ...

  • Zenoah G455AVS - page 18

    B. Guide Bar • Reverse the bar occasionally to prevent partial wear. • The bar rail should always be a square. Check for wear of the bar rail. Apply a ruler to the bar and the outside of a cutter. If a gap is observed between them, the rail is normal. Otherwise, the bar rail is worn. Such a bar needs to be corrected or replaced. 16 WARNING: Thi ...

  • Zenoah G455AVS - page 19

    Check fuel for water or incorrect mixture. Replace with proper fuel. Check engine for flooding. Remove and dry the spark plug. Repeat pulling starter with no choke. Remove spark plug and check for correct sparking. Replace with a new plug. 8. T roubleshooting Guide 17 Case 1. Starting failure: Check fuel for water or incorrect mixture. Replace with ...

  • Zenoah G455AVS - page 20

    9. Specifications Model G455AVS Power unit: Dis placement cc (cu. in.) 45.0 (2. 75) Fuel Mixture (Gasoline 32: Two-cycle oil 1) Fuel tank capacity cc (pints) 550 (1.17) Chain oil Motor oil SAE#10W-30 Oil tank capacity cc (pints) 260 (0.55) Carburetor Diaphragm type (Walbro WT) Ignition system C.D.I. with timing advance function Spark plug Champion ...

  • Zenoah G455AVS - page 21

    10. Parts List NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/or replacement. 2. KOMATSU ZENOAH does not warrant the machines, which have been damaged by the use of any parts other than those specified by the company. 3. When placing parts orders for repair and/or replacement, check if the model name and th ...

  • Zenoah G455AVS - page 22

    10. Parts List : G455A VS 20 ...

  • Zenoah G455AVS - page 23

    21 ...

  • Zenoah G455AVS - page 24

    Key# Part Number Description Q'ty NOTE 1 2670-12112 CYLINDER 1 2 2810-14110 INLET PIPE 1 3 2817-14121 GASKET 1 ✻ 1 4 2670-14130 SCREW 2 5 2880-14150 GUIDE 1 6 2670-14311 BRACKET 1 7 2670-14320 SCREW 2 8 2880-14350 SPACER 1 9 2880-14360 GASKET 1 10 2670-14211 GASKET 1 ✻ 1 11 2850-14220 BOLT 4 12 2810-15220 BOLT 2 13 2850-15230 NUT 2 14 2812 ...

  • Zenoah G455AVS - page 25

    Key# Part Number Description Q'ty NOTE 107 2880-35211 DAMPER 2 108 3350-35170 BOLT 2 109 2880-35250 CAP 2 110 2810-31115 CYLINDER COVER 1 111 2670-14320 SCREW 5 112 3359-83340 LABEL 1 113 2810-83305 CLEANER COVER COMP. 1 114 3356-83322 KNOB 1 115 3388-83340 GASKET 1 116 2810-83500 CLEANER COMP. 1 117 2810-83520 SEAL 1 118 1600-33130 SCREW 1 11 ...

  • Zenoah G455AVS - page 26

    10. Parts List : G455A VS 24 ...

  • Zenoah G455AVS - page 27

    25 ✻ 1 Special tools (Opt. Part) Key# Part Number Description Q'ty NOTE 1 2812-81000 CARBURETOR ASS’Y – 2 3306-81380 SCREEN 1 3 2810-81120 COVER 1 4 3310-81130 SCREW 1 5 ––––––––– ––––––– – 6 2812-06020 GASKET KIT 1 7 ––––––––– ––––––– – 8 ––––––––– – ...

  • Zenoah G455AVS - page 28

    THE CALIFORNIA AIR RESOURCES BOARD AND KOMATSU ZENOAH Co. ARE PLEASED TO EXPLAIN THE EMISSION CONTROL SYSTEM WARRANTY ON YOUR 1995 AND LATER LAWN AND GARDEN EQUIPMENT ENGINE. IN CALIFORNIA, NEW UTILITY AND LAWN AND GARDEN EQUIPMENT ENGINES MUST BE DESIGNED, BUILT AND EQUIPPED TO MEET THE STATE'S STRINGENT ANTI-SMOG STANDARDS. KOMATSU ZENOAH Co ...

  • Zenoah G455AVS - page 29

    RedMax CHAIN SAW MODELS G455AVS 1-YEAR LIMITED WARRANTY KOMATSU ZENOAH AMERICA INC. 1505 Pavilion Place Suite A Norcross, Georgia 30093  EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY OF THE MODEL G455AVS UNIT, KOMATSU ZENOAH AMERICA INC. (THE COMPANY), THROUGH ANY RedMax DEALER, WILL REPAIR OR REPLACE, FREE OF CHAR ...

  • Zenoah G455AVS - page 30

    KOMATSU ZENOAH AMERICA INC. 1505 Pavilion Place Suite A Norcross, Georgia 30093  Printed in Japan ...

Fabricant Zenoah Catégorie Chainsaw

Les documents que nous recevons du fabricant de l'appareilZenoah G455AVS peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Zenoah
- manuels d’utilisations G455AVS
- fiches produit Zenoah
- dépliants
- ou étiquettes-énergie Zenoah G455AVS
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Zenoah G455AVS.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Zenoah G455AVS, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Zenoah G455AVS. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Zenoah G455AVS.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Zenoah G455AVS, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Zenoah G455AVS par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Zenoah G455AVS.

Le manuel d’utilisation complet Zenoah, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Zenoah G455AVS - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Zenoah G455AVS, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lZenoah G455AVS qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Zenoah G455AVS - qui devraient nous aider dans les premières étapes lors de l'utilisation Zenoah G455AVS
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Zenoah G455AVS
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Zenoah G455AVS dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Zenoah G455AVS?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Zenoah G455AVS, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Zenoah G455AVS il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)