-
Kenwood CD-403 - page 1
INSTRUCTION MANUAL KENW OOD CORPORA TION B60-4404-01 (EN) CD PLA YER DPF-R 6030 CD-406 DPF-R 4030 CD-404 DPF-R 3030 CD-403 This instruction manual is used to describe multiple models listed above. Model availability and features (functions) may differ depending on the country and sales area. DTS disclaimer clause When playing DTS-encoded CDs, exces ...
-
Kenwood CD-403 - page 2
2 The illustration shows the CD-406/DPF-R6030. Factory fitted moulded mains plug 1. The mains plug contains a fuse. For replacement, use only a 13- Amp A ST A-appro ved (BS1 362) fuse. 2. The fuse cover must be refitted when replacing the fuse in the moulded plug. 3. Do not cut off the mains plug from this equipment. If the plug fitted is not suita ...
-
Kenwood CD-403 - page 3
3 Unpack the unit carefully and make sure that all accessories are put aside so they will not be lost. Examine the unit for any possibility of shipping damage. If your unit is damaged or fails to operate, notify your dealer immediately. If your unit was shipped to you directly, notify the shipping company without delay. Only the consignee (the pers ...
-
Kenwood CD-403 - page 4
4 SYSTEM CONTROL DIGITAL OUTPUT LINE OUTPUT VARIABLE OPTICAL R L TEXT SYSTEM CONTROL DIGITAL OUTPUT LINE OUTPUT VARIABLE COAXIAL OPTICAL R L L R CD SYSTEM CONTROL OPTICAL COAXIAL DIGITAL INPUT TEXT System connections Caution: Do not plug in the power lead until all connections are completed. If operation is not possible or erroneous display appears ...
-
Kenwood CD-403 - page 5
5 The OUTPUT level (UP/DOWN) keys of the remote control unit can adjust the output levels from the LINE/OUT and PHONES jack of the unit. Connect a stereo headphone to the PHONES jack of the CD player. Output level ÷ It is not favorable for the sound quality to decrease the output level from this unit too much. Use these keys for coordination with ...
-
Kenwood CD-403 - page 6
6 CHECK ON/STANDBY POWER CLEAR P.MODE TIME DISP. RANDOM REPEAT DISC 2 DISC 1 DISC 1 DISC SKIP DISC 2 DISC 3 DISC 4 DISC 5 OPEN/CLOSE PHONES DISC 3 DISC 4 DISC 5 ON/STANDBY AUTO PAUSE ALL 0 SINGLE TOTAL 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 REPEAT TRACK NO. DISC NO. MULTI EDIT FILE RANDOM PGM 5 4 3 2 1 P.C. B A Controls and indicators P ...
-
Kenwood CD-403 - page 7
7 The keys with the same name as those on the remote control unit operate the same way as the remote control unit. 1 ON/STANDBY (POWER / ) key 9 Turns the unit ON/STANDBY. 2 P.MODE key # Used for playback mode switching. 3 CHECK key $ Used to check or change program contents. 4 CLEAR key % Used to clear the program. 5 Remote control light sensor (C ...
-
Kenwood CD-403 - page 8
8 Operation of remote control unit (Except for CD-403/DPF-R3030) 1. The supplied batteries are intended for use in operation checks. Therefore, their lives may be shorter than ordinary batteries. 2. When the remote-controllable distance gets shorter than before, replace both batteries with new ones. 3. Malfunction may occur if direct sunlight or th ...
-
Kenwood CD-403 - page 9
9 1 Preparing to play tracks Load/unload a disc. Close the tray. All DISC indicators " " light regardless of how many discs are present. Label side Disc tray 2 Place/remove a disc. 3 When loading or unloading other discs Preparation • Turn the unit ON. ÷ Do not touch the played side of disc. Press the ON/STANDBY (POWER / )key. CD-406/D ...
-
Kenwood CD-403 - page 10
10 Check that the unit is in the TRACK mode. ! ÷ Playback starts from the disc selected in order of the DISC No. ÷ When the 3 / 8 key is pressed without selecting a disc, playback starts from the indicated DISC No. Normal play (TRACK mode) Use the following procedure to play a CD in the original order of tracks from track No. 1. ÷ Each press pau ...
-
Kenwood CD-403 - page 11
11 Skipping tracks Playback from desired track 2 Select the desired track No. 1 Select the disc. ÷ The track in the direction of the pressed key is skipped, and the selected track will be played from the beginning. To skip forward To skip backward Searching ÷ Playback starts from the position where the key is released. Forward search Backward sea ...
-
Kenwood CD-403 - page 12
12 You can select the display type and check the disc informa- tion. ÷ Load a disc in the CD player. Preparation Displays Display scrolling (CD-406/DPF-R6030 only) Some titles contain so much text information that the full titles will not fit on the display. In cases like this, the letters on the display move from right to left so that the non-vis ...
-
Kenwood CD-403 - page 13
13 Programmed play (PGM mode) Use the following procedure to program desired tracks in a desired order. (up to 32 tracks) ÷ Load a disc in the CD player. Press so that the “PGM” indicator lights. 1 Preparation Do this operation in the stop mode. ÷ Up to 32 tracks can be programmed. When “FULL” is displayed, no more tracks can be programme ...
-
Kenwood CD-403 - page 14
14 T o check or change the programmed tracks 1 Press the CHECK key. Press until the track No. to be changed is displayed. 2 Select the disc. 3 Select the new track No. 4 Set the entry. T o add a track to the program 1 Select the disc. 2 Select the desired track No. 3 Press the P.MODE key. Blinks. ÷ Perform only step 1 to simply check the program. ...
-
Kenwood CD-403 - page 15
15 Press to clear tracks from the end. T o clear tracks from the program To clear all tracks ÷ Each time the key is pressed, the last track in the program is cleared. ÷ The tracks which are programmed earlier than the track being played cannot be cleared. ÷ Selected tracks can be also completely cleared just by operating the OPEN/CLOSE ( 0 ) key ...
-
Kenwood CD-403 - page 16
16 Playback in a random order (Random playback) ™ As tracks are selected at random, you can enjoy listening to for a long time. ÷ Load a disc in the CD player. Preparation 1 2 Press the RANDOM key. In case track No. 5 is selected ÷ Each time a track ends, the same operation as above is repeated, and the track selected next is played. ÷ Random ...
-
Kenwood CD-403 - page 17
17 Repeated playback ™ Preparation ÷ Load a disc in the CD player. T o repeat the entire disc This allows repeated playback of all the tracks on the disc loaded in the disc tray. 1 Press so that the “PGM” indicator goes off. 2 Press the REPEAT key. For the CD-406/DPF-R6030 The current status is displayed when the key is pressed once. When it ...
-
Kenwood CD-403 - page 18
18 T o cancel repeated playback Press the REPEAT key. Repeated playback REPEAT indicator goes off. CD-406/DPF-R6030 CD-404/403/DPF-R4030/R3030 REPEAT 1 Press so that the “PGM” indicator lights. T o repeat only the programmed tracks 2 Select the disc. 3 Select the desired track number. 4 Set the entry. 5 Repeat steps 2 – 4 above. 6 Press the R ...
-
Kenwood CD-403 - page 19
19 Blinks. CD-406/DPF-R6030 The following procedure allows to record a CD within the specified tape length so that no music is interrupted in the middle at the ends of sides A and B. Editing (Except for CD-403/DPF-R3030) Preparation 1 Light the “EDIT” indicator. ÷ Load a disc in the CD player. ÷ Check that the unit is in the TRACK mode. ! Sel ...
-
Kenwood CD-403 - page 20
20 T o clear the edited contents T o check the edited contents ÷ When the CHECK key is pressed, track numbers and remaining time in the file A are displayed first, then those in the file B. Playing or recording the edited contents Press the 6 key to start playback according to the edited content. The playback pauses at the beginning of the track e ...
-
Kenwood CD-403 - page 21
21 T imer operations Timer playback of CD can be started at any time using an audio timer which is available in audio stores. 1 Turn the powers of the associated components ON. 2 Preparation Load a disc in the CD player. 9 Set the amplifier volume. 3 1 Play the disc. Set the timer ON time. 4 Set the timer so that it supplies power at the specified ...
-
Kenwood CD-403 - page 22
22 Never play a cracked or warped disc. Cleaning If fingerprints or foreign matter be- come attached to the disc, lightly wipe the disc with a soft cotton cloth (or similar) from the center of the disc outwards in a radial manner. Storage When a disc is not to be played for a long period of time, remove it from the player and store it in its case. ...
-
Kenwood CD-403 - page 23
23 ÷ Power plug is loosely connected. ÷ With the power plug connected to the switched AC outlet of an amplifier, the power of the amplifier is turned off. ÷ Disc is loose. ÷ Disc is too dirty. ÷ Disc is cracked. ÷ Condensation has occurred on the optical lens unit. ÷ The connection cords are inserted loosely. ÷ Output level is attenuated to ...
-
Kenwood CD-403 - page 24
24 Specifications DPF-R6030 / CD-406 [ Format ] System .......................... Compact disc digital audio system Laser ...................................................... Semiconductor laser [ D/A Convertors ] D/A Conversion ........................................... 1 Bit (D.R.I.V.E.) Oversampling ........................................... ...
Avez-vous une question à propos de Kenwood CD-403?
Utiliser le formulaire ci-dessous
Si vous n’avez pas résolu votre problème avec Kenwood CD-403, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Kenwood CD-403 il est probable qu’il a envie de partager la façon de le résoudre.