-
Makita 1100 - page 1
Power Planer Planing width 82 mm (344”) MODEL 1100 Planing Rabbeting No load speed Overall Net depth depth (RPM) length weight INSTRUCTION MANUAL 82 mm (3-114”) DOUBLE INSULATION 415 mm 4.9 kg (1 6-318”) (10.8 Ibs) 16,000 3 mm 20 mm (118“) (314”) SPECIFICATIONS Manufacturer reserves the right to change specifications without notice. * Not ...
-
Makita 1100 - page 2
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 2 KEEP WORK AREA CLEAN. Cluttered areas and benches invit ...
-
Makita 1100 - page 3
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only ext ...
-
Makita 1100 - page 4
ADDITIONAL SAFETY RULES 1. Rags, cloth, cord, string and the like should never be left around the work 2. Avoid cutting nails. Inspect for and remove all nails from the workpiece before 3. Handle the blades very carefully. 4. Be sure the blade installation bolts are securely tightened before operation. 5. Hold the tool firmly with both hands. 6. Ke ...
-
Makita 1100 - page 5
Removing or installing mini planer blades CAUTION : Always be sure that the tool is switched off and unplugged before removing or installing the blade. To remove the blades on the drum, un- screw the three installation bolts with the socket wrench. The drum cover comes off together with the blades. 1. Remove the existing blade, if the tool has been ...
-
Makita 1100 - page 6
7. The blade's lengthwise adjustment will need to be manually positioned so that the blade ends are clear and equidistant from the housing on one side and the metal bracket on the other. 8. Tighten the three hex flange head bolts (with the socket wrench provided) and hand rotate the drum to check clear- ances between the blade ends and the too ...
-
Makita 1100 - page 7
For the correct planer blade setting Your planing surface will end up rough and uneven, unless the blade is set properly and securely. The blade must be mounted so that the cutting edge is absolutely level, that is, parallel to the surface of the rear base. Below are some examples of proper and improper settings . (A) Front base (Movable shoe) (6) ...
-
Makita 1100 - page 8
Switch action To start the tool, simply pull the trigger. Release the trigger to stop. For continuous operation, pull the trigger and then push in Lock button - the lock button. To stop the tool from the locked position, pull the trigger fully, then release it. CAUTION : Before plugging in the tool, always check to see that the trigger switch actua ...
-
Makita 1100 - page 9
Shiplapping To make a stepped cut as shown at the right, use the edge fence. Draw a cutting line on the workpiece. In- sert the edge fence into the hole in the front of the tool. Align the blade edge with the cutting line. Adjust the edge fence until it comes in con- tact with the side of the workpiece, then secure it by tightening the screw. You m ...
-
Makita 1100 - page 10
Chamfering To make a cut as shown at the right, align the "V" groove in the front base with the edge of the workpiece and plane it as shown in the figure (A). Sharpening planer blades Always keep your blades sharp for the best performance possible. Use the sharpening holder to remove nicks and produce a fine edge. First, loosen the two wi ...
-
Makita 1100 - page 11
Immerse the dressing stone in water for 2 or 3 minutes before sharpening. Hold the holder so that the blades both contact the dressing stone for simultaneous sharpening at the same angle. 11 ...
-
Makita 1100 - page 12
MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be r ...
-
Makita 1100 - page 13
ACCESSOR I ES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Replacement baldes Width : 82 mm (3-1/4&qu ...
-
Makita 1100 - page 14
May-l5-'90 US 82 mm (3-1/4') POWER PLANER Model 1100 Note: The switch, noise suppressor and other part configurations may differ from country to country. 14 ...
-
Makita 1100 - page 15
MODEL 1100 ITEM NO. NO. USED MACHINE __ MACHlNE 33 34 35 36 37 38 39 40 41 42 43 44 45 46 41 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 Mav-15-'90 US DESCRIPTION 'Yz G2D DESCRIPTION 5 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 6 2 4 2 2 1 1 1 1 1 1 1 1 4 1 1 1 2 3 4 5 6 7 8 9 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 21 28 29 30 31 32 - ...
-
Makita 1100 - page 16
f MAKITA LlMrED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one- year period, return the COMPLETE tool, frei ...
Avez-vous une question à propos de Makita 1100?
Utiliser le formulaire ci-dessous
Si vous n’avez pas résolu votre problème avec Makita 1100, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Makita 1100 il est probable qu’il a envie de partager la façon de le résoudre.