Manuel d’utilisation TOA Electronics CST-38

24 pages 0.34 mb
Télécharger

Aller à la page of 24

Summary
  • TOA Electronics CST-38 - page 1

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 1 36" Wood Burning Fireplaces P/N 700,023M REV. C 06/2005 CST -38 CPF-38 MODELS CUSTOM SERIES This installation manual will enable you to obtain a safe, efficient and dependable installation of your fireplace system. Please read and under- stand these instructions before beginning your installat ...

  • TOA Electronics CST-38 - page 2

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 2 IMPORTANT: PLEASE READ AND UNDERSTAND THESE RULES TO FOLLOW FOR SAFETY. 1. Before starting your fireplace installation, read these installation instructions carefully to be sure you understand them completely and in entirety. Failure to follow them could cause a fireplace malfunction resulting in s ...

  • TOA Electronics CST-38 - page 3

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 3 Figure 1 TYPICAL INSTALLATION *Construction Materials: • framing materials • paneling • particle board • flooring • millboard • dry wall • plywood • etc. PRECAUTIONS Note: These fireplace systems are not difficult to install. However, in the interest of safety, it is recommended tha ...

  • TOA Electronics CST-38 - page 4

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 4 For questions, please call your distributor or the manufacturer. Special restrictions apply to the front and facing of the fireplace and nearby walls (See pages 18, 19 and 20 ). CHIMNEY SYSTEM These fireplaces are designed and code listed for use with Security Chimneys FTF8 chimney System only. Alw ...

  • TOA Electronics CST-38 - page 5

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 5 Figure 7 Figure 6 Carefully consider the position of the fireplace opening with respect to the location of adja- cent or nearby stairwells, bath or kitchen ex- haust fans and/or return air registers for forced air furnaces/air conditioners that could cause a smoking fireplace condition if the house ...

  • TOA Electronics CST-38 - page 6

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 6 The safety strips should extend in front and sides of the fireplace opening 2" (51 mm) . In the event a wooden support is used to elevate the fireplace above the floor, a “Z” type safety strip should be fabricated and used to protect the front surface of the wood support as well as the flo ...

  • TOA Electronics CST-38 - page 7

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 7 FIREPLACE SPECIFICATIONS Figure 15 39 ¹⁄₄ " (997 mm) 23 ¹⁵⁄₁₆ " (608 mm) 25 ³⁄₁₆ " (640 mm) 8" (203 mm) Left Front View Model CPF-38 Front View Model CST -38 T op View End View 12 ¹⁄₂ " (318 mm) 48 ³⁄₄ " (1238 mm) 8 ⁹⁄₁₆ " (2 ...

  • TOA Electronics CST-38 - page 8

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 8 Figure 16 Figure 19 CPF CST Figure 17 Figure 18 Figure 21 CST - Front View CST - End View CPF - Right Front View CPF - End View FRAMING SPECIFICATIONS Figure 20 7" Min. (178 mm) 23 ¹⁵⁄₁₆ " (608 mm) 49" (1245 mm) 4 x 4 Header 2 x 4 False Header (Optional) 39 ¹⁄₈ " ( ...

  • TOA Electronics CST-38 - page 9

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 9 Figure 22 FRAMING WALL VARIATIONS As many as six (6) different framed wall con- figurations can be constructed to enclose the CST and CPF fireplaces. The following illustra- tions depict these variations of wall enclosures. Several of these designs may incorporate book shelves, wood storage boxes, ...

  • TOA Electronics CST-38 - page 10

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 10 A minimum 2" (51 mm) air space must be reserved for all combustible materials extend- ing for any continuous length surrounding the chimney. Reference Figures 24 and 25 and charts “Fram- ing Dimensions for Ceiling and Roof” on page 8, which specify minimum ceiling and roof dimensions. For ...

  • TOA Electronics CST-38 - page 11

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 11 Check vertical alignment of chimney pipe so that it projects from the roof in a true vertical position. Security's chimney sections do not need to be screwed together. Additional rein- forcement is not necessary, except in certain offset conditions (see to page 16, Figure 47 ). Step 5. The he ...

  • TOA Electronics CST-38 - page 12

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 12 Figure 40 Step 10. Using an FTF8-CTD Round Termi- nation: 1. Hold FTF8-CTD over top of last chimney section ( Figure 40 ). 2. Center inner slip section in inner flue pipe- slip down. 3. Center outer locking section over outer flue pipe. Push down until locking tabs are firmly engaged. 4. Pull up s ...

  • TOA Electronics CST-38 - page 13

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 13 Figure 41 TEN FOOT RULE SUMMARY The minimum chimney height above the roof and/or to adjacent walls and buildings is speci- fied by all major building codes. If the horizontal distance from the peak of the roof is less then 10' (3 m), the top of the chimney must be at least 2' (610 mm) ab ...

  • TOA Electronics CST-38 - page 14

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 14 11 0 11 1 0 0 0 279 0.28 17 1 5 0 1 0 0 432 0.43 21 ¹⁄₄ 19 ¹⁄₄ 2 0 0 0 540 0.54 27 ¹⁄₄ 23 ¹⁄₄ 1 1 0 0 692 0.69 35 2 11 0 0 1 0 889 0.89 47 3 11 0 0 0 1 1194 1.19 51 ¹⁄₄ 43 ¹⁄₄ 0 1 1 0 1302 1.30 57 ¹⁄₄ 49 ¹⁄₄ 1 0 0 1 1454 1.45 63 ¹⁄₄ 53 ¹⁄₄ 0 1 0 1 ...

  • TOA Electronics CST-38 - page 15

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 15 A B FTF8-ES30 Number of FTF8 A B Offset Height Offset/Return FTF8-S4 Chimney Sections Offset Height (Inches) (Inches) Elbow Set Stabilizer 12" 18" 36" 48" (mm) (mm) 41 5 ³⁄₄ 1 0 0 0 0 0 102 400 92 4 ¹⁄₂ 1 0 1 0 0 0 229 622 12 29 ³⁄₄ 1 0 0 1 0 0 305 756 14 ¹⁄? ...

  • TOA Electronics CST-38 - page 16

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 16 OFFSET ELBOW ASSEMBLY Offset elbows install the same as chimney sections. First, snap the inner section INTO the preceding inner section of flue. Check connec- tion by pulling up slightly to ensure a tight fit. Next, the outer sections snap locks OVER the preceding outer section of chimney. Again, ...

  • TOA Electronics CST-38 - page 17

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 17 There is a one-hand operated shut-off valve located in the enclosed corner of the fireplace opening behind the screen. Refer to label for directions of operation. The combustion air damper should be fully open when the fire- place is in operation and fully closed when the fireplace is not in use t ...

  • TOA Electronics CST-38 - page 18

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 18 GAS LINE INSTALLATION The CST and CPF fireplaces have been ap- proved to accept a ¹⁄₂ " (13 mm) gas line for an approved gas appliance. Always have the appli- ance installed by a qualified, licensed plumber in accordance with all local building codes. The gas line may enter either end of ...

  • TOA Electronics CST-38 - page 19

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 19 If there is a continuous perpendicular side wall closer than 18" (mm) from the CST-38 fireplace opening, it must be protected with a 40 x 40" x ¹⁄₂ " (1016 mmx 1016 mm x 13 mm) wall shield constructed of millboard or a durable noncom- bustible material with an equal or greater ...

  • TOA Electronics CST-38 - page 20

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 20 Example: Given that the required “R value” for a suitable hearth extension used must be equal to or greater than: “R” = r x T L = 1.19 x 1 " = 1.19. If it is desired to elevate a marble hearth exten- sion to a level of 5" or more above the floor surface. What combination of nonco ...

  • TOA Electronics CST-38 - page 21

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 21 ACCESSORIES AND COMPONENTS 63L10 FTF8-12 63L13 FTF8-18 63L14 FTF8-36 Chimney Section 63L15 FTF8-48 Canadian (Outside) 62L92 FTF8-18C Chimney Section 62L93 FTF8-36C Offset/Return Elbow 63L28 FTF8-OR15 Offset/Return Package 63L22 FTF8-ES30 (Canada Only) 63L69 FTF8-ES45C Stabilizer 63L25 FTF8-S4 Fire ...

  • TOA Electronics CST-38 - page 22

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 22 Combustion Air Kit 011761 AK-4 (Less Duct) 011763 AK-4LD “All-Glass TM ” 38AEP Aluminum End Panel 38AEP-BB “All-Glass TM ” Cabinet Doors 38TBA-BB “All-Glass TM ” 38ABF Aluminum Doors 38ABF-BB Chimney Air Kit 81L87 FOAK-4 (less duct) 81L88 FOAK-4LD ACCESSORIES AND COMPONENTS 96L20 FTF8- ...

  • TOA Electronics CST-38 - page 23

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 23 ...

  • TOA Electronics CST-38 - page 24

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 24 Printed in U.S.A. © 2001 by LENNOX HEARTH PRODUCTS P/N 700,023M REV. C 06/2005 The manufacturer reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor for fire ...

Fabricant TOA Electronics Catégorie Indoor Fireplace

Les documents que nous recevons du fabricant de l'appareilTOA Electronics CST-38 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques TOA Electronics
- manuels d’utilisations CST-38
- fiches produit TOA Electronics
- dépliants
- ou étiquettes-énergie TOA Electronics CST-38
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation TOA Electronics CST-38.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation TOA Electronics CST-38, manuels d’entretien, brefs manuels ou manuels de l’utilisateur TOA Electronics CST-38. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit TOA Electronics CST-38.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil TOA Electronics CST-38, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser TOA Electronics CST-38 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs TOA Electronics CST-38.

Le manuel d’utilisation complet TOA Electronics, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel TOA Electronics CST-38 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières TOA Electronics CST-38, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lTOA Electronics CST-38 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil TOA Electronics CST-38 - qui devraient nous aider dans les premières étapes lors de l'utilisation TOA Electronics CST-38
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de TOA Electronics CST-38
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service TOA Electronics CST-38 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de TOA Electronics CST-38?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec TOA Electronics CST-38, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec TOA Electronics CST-38 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (0)