Français dropdown-ico

Manuel d’utilisation MaxTech 56K BPS

21 pages 0.06 mb
Télécharger

Aller à la page of 21

Summary
  • MaxTech 56K BPS - page 1

    Part #MAN117 Rev. 1.0 K56Plus/HIS-FM High Performance K56Plus/V.34+/V.42bis 56K BPS Plug & Play Internal FAX/Data Modem User's Manual Contents Section One - Introduction .......................... 1 Section Two - Installation ............................ 1 Section Three - AT Command Set .............. 7 Section Four - S Registers ......... ...

  • MaxTech 56K BPS - page 2

    The information contained in this manual has been validated at the time of this manual's production. The manufacturer reserves the right to make any changes and improvements in the product de- scribed in this manual at any time and without notice. Consequently the manufacturer assumes no liability for damages incurred directly or indi- rectly ...

  • MaxTech 56K BPS - page 3

    1 Section One - Introduction This 56 Kbps* Plug and Play FAX/Data Modem connects your computer to all popular high speed modems available today. The modem incorporates “K56Plus” (56Kbps) technology to provide increased download speeds using regular telephone lines. The modem incorporates Plug and Play for ease of instal- lation. This manual des ...

  • MaxTech 56K BPS - page 4

    2 Proceed to Section 2.3 now if you have every- thing required. If you have neither 2A or 2B above, you have two options to provide Plug and Play functionality to your PC. 1. Install Windows 95 or, 2. If running DOS or Windows 3.x, configure the modem using the included modem driver. Instructions for installing this driver are included in the text ...

  • MaxTech 56K BPS - page 5

    3 4. Carefully slide the internal modem into the slot you have chosen, applying even pressure until the modem is completely seated in the slot. 5. Fasten the retaining bracket with the screw from the slot cover. Make sure the modem is properly aligned. Store the slot cover for future use. 6. Replace the computer cover and plug in your computer. 7. ...

  • MaxTech 56K BPS - page 6

    4 • Section 2.4.1.1 when Windows 95 starts for the first time after card installation, it detects the modem and it displays the New Hardware Found dialog box • Section 2.4.1.2 when Windows 95 starts for the first time after card installation, it detects the modem and it displays the Update Device Driver Wizard . 2.4.1.1 Windows 95 Release 4.00. ...

  • MaxTech 56K BPS - page 7

    5 2.4.2 Configuring in a Plug and Play System with- out Windows 95 When this modem is installed in a Plug and Play system without Windows 95, the computer's BIOS will assign a COM port and IRQ line to the modem. Proceed to Section 2.5, Software Installation/ Configuration. 2.4.3 Configuring in a Non-Plug and Play System Computers without nativ ...

  • MaxTech 56K BPS - page 8

    6 Note that your software must be configured to communicate with the modem on the same COM port and IRQ line used by the modem. 2.6 Testing Your Modem After Installation In order to test your modem you should be familiar with your communication software. Load and set up your communication software and enter into “terminal mode.” Make sure that ...

  • MaxTech 56K BPS - page 9

    7 contain reference material, and can be skipped. If you have difficulties getting your modem to work, read Section 6 - Troubleshooting to find answers to com- monly asked questions and problems. Section Three - AT Command Set 3.1 Executing Commands Commands are accepted by the modem while it is in Command Mode. Your modem is automatically in Comma ...

  • MaxTech 56K BPS - page 10

    8 D _ 0 - 9, A-D, # and * L last number redial P pulse dialing T touch-tone dialing W wait for second dial tone , pause @ wait for five seconds of silence ! flash ; return to Command Mode after dialing DS=n Dial one of the four telephone numbers (n=0-3) stored in the modem’s non- volatile memory. E_ E0 Commands are not echoed E1 Commands are echo ...

  • MaxTech 56K BPS - page 11

    9 Sr=n Set register r to value n (n = 0-255). T Set Tone Dial as default V_ V0 Numeric responses V1 Word responses W_ W0 Report DTE speed only W 1 Report line speed, error correction protocol, and DTE speed. W2 Report DCE speed only X _ X0 Hayes Smartmodem 300 compatible responses/blind dialing. X 1 Same as X0 plus all CONNECT responses/blind diali ...

  • MaxTech 56K BPS - page 12

    10 &K5 Enable transparent XON/XOFF flow control &K6 Enable both RTS/CTS and XON/XOFF flow control &L_ &L0 Modem is set up for dial-up operation &M_ &M0 Asynchronous operation &P_ &P0 US setting for off-hook-to-on-hook ratio &P1 UK and Hong Kong off-hook-to-on-hook ratio &P2 Same as &P0 setting but at 20 p ...

  • MaxTech 56K BPS - page 13

    11 %E_ %E 0 Disable auto-retrain %E1 Enable auto-retrain +MS? Displays the current Select Modulation settings +MS=? Displays a list of supported Select Modulation options +MS=a,b,c,d.e,f Select modulation where: a =0, 1, 2, 3, 9, 10, 11, 56, 64, 69; b =0-1; c =300- 56000; d =300-56000; e =0-1; and f =0- 1. A, b, c, d, e, f default= 56, 1, 300, 5600 ...

  • MaxTech 56K BPS - page 14

    12 &Q_ &Q0 Direct data link only (same as N1) &Q5 V.42 data link with fallback options &Q6 Normal data link only (same as N0) A_ A0 64-character maximum MNP block size A1 128-character maximum MNP block size A2 192-character maximum MNP block size A3 256-character maximum MNP block size Bn Send a 1/10 second line break to th ...

  • MaxTech 56K BPS - page 15

    13 Table 4-1 S - Registers Register Function Range/units Default S0 Auto-answer Ring 0-255 /rings 0 S1 Ring counter 0-255 /rings 0 S2 Escape code character 0-127 /ASCII 43 S3 Carriage return character 0-127 /ASCII 13 S4 Line feed character 0-127 /ASCII 10 S5 Backspace character 0-32, 127 /ASCII 8 S6 Dial tone wait time 2-255 /seconds 2 S7 Remote ca ...

  • MaxTech 56K BPS - page 16

    14 S49-81 Reserved S82 Break options 3, 7, or 128 1 28 S83-85 Reserved S86 Connection failure code 0, 4, 5, 9, 12, 13, 14 S87-S90 Reserved S91 Transmit attenuation 0-15/dBm 10 S92 Fax attenuation 0-15/dBm 10 S95 Extended result code options Bit-mapped register 0 Section Five - Result Codes OK 0 CONNECT 1 RING 2 NO CARRIER 3 ERROR 4 CONNECT 1200 5 N ...

  • MaxTech 56K BPS - page 17

    15 Section Six - Troubleshooting This section describes some of the common problems you may encounter while using your modem. If you can not resolve your difficulty after reading this chapter, contact your dealer or vendor for assistance. Modem does not respond to commands. 1. Make sure the communication software is configured to “talk” to the ...

  • MaxTech 56K BPS - page 18

    16 used. 2. Make sure the correct terminal emulation mode is being used (see communication software manual). High pitch tone is heard whenever you answer the phone. 1. Make sure Auto-Answer is turned off. Your modem is factory configured to NOT auto-answer. Issue AT&F to factory reset your modem. Modem experiences errors while communicating wit ...

  • MaxTech 56K BPS - page 19

    17 Appendix A - Specifications Communication Std. K56FLEX (56Kbps), V.34, V.32bis, V.32, V.29, V.27ter, V.22bis, V.23, V.22, V.21, V.17, Bell212/103 Data Compression: V.42bis/MNP5 Error Correction: V.42/MNP2-4 Host Interface: 16 bit PC bus COM ports: 1, 2, 3, 4 IRQ lines: 3, 4, 5, 7, 9, 10, 11, 12, 15 FAX Group: Group III Send/Receive Standard FAX ...

  • MaxTech 56K BPS - page 20

    18 The FCC prohibits this equipment to be connected to party lines or coin-telephone service. In the event that this equipment should fail to operate properly, disconnect the equipment from the phone line to determine if it is causing the problem. If the problem is with the equipment, discontinue use and contact your dealer or ven- dor. The FCC als ...

  • MaxTech 56K BPS - page 21

    19 permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be made by an ...

Fabricant MaxTech Catégorie Network Card

Les documents que nous recevons du fabricant de l'appareilMaxTech 56K BPS peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques MaxTech
- manuels d’utilisations 56K BPS
- fiches produit MaxTech
- dépliants
- ou étiquettes-énergie MaxTech 56K BPS
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation MaxTech 56K BPS.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation MaxTech 56K BPS, manuels d’entretien, brefs manuels ou manuels de l’utilisateur MaxTech 56K BPS. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit MaxTech 56K BPS.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil MaxTech 56K BPS, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser MaxTech 56K BPS par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs MaxTech 56K BPS.

Le manuel d’utilisation complet MaxTech, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel MaxTech 56K BPS - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières MaxTech 56K BPS, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lMaxTech 56K BPS qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil MaxTech 56K BPS - qui devraient nous aider dans les premières étapes lors de l'utilisation MaxTech 56K BPS
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de MaxTech 56K BPS
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service MaxTech 56K BPS dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de MaxTech 56K BPS?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec MaxTech 56K BPS, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec MaxTech 56K BPS il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)