Français dropdown-ico

Manuel d’utilisation Northern Industrial Tools M157300E

23 pages 0.96 mb
Télécharger

Aller à la page of 23

Summary
  • Northern Industrial Tools M157300E - page 1

    1 Pump is shipped with oil. - Remove ship ping tape from pump oil fill cap . (Cat Pumps) - Remove ship ping plug and instal l vented fill cap. (Comet Pumps) - See pump oil cap section of t his manual. Closely inspect all components. -If you have damaged components: Contact the f reight company th at delivered the unit and file a claim. -If you have ...

  • Northern Industrial Tools M157300E - page 2

    Hazard Signal Word Definitions 2 ...

  • Northern Industrial Tools M157300E - page 3

    Table of Contents 3 Important Safety Instructions……………………….... 4-5 Warning Label Locations……………………………... 6 Assembly Instructions……………………………………. 7-9 Machine Component Identification……………………… 10 Pump Oil Cap and Pump Component Identification….. 11 Operation Instru ...

  • Northern Industrial Tools M157300E - page 4

    Important Safety Instructions 4 WARNING -Risk of Injection or Injury to Persons - Do Not Direct Discharge Stream at Persons. - Do not use a hose if exterior damage is evident. -Risk of explosion. - Do not spray flammable liquids. - Do not operate in a flammable environment. CAUTION -Gun kicks back. Hold with both hands. -To reduce the risk of injur ...

  • Northern Industrial Tools M157300E - page 5

    Grounding Instructions 5 This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of elec trical shock. Th is product is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appr opriate o ...

  • Northern Industrial Tools M157300E - page 6

    Warning Label Locations 6  Gun kicks back. Hold with both hands.  Risk of injection or in jury to perso ns. Do not direct discharge st re am at persons.  Risk of fire and explosio n. Do not spray flammable liquids.  To reduce the risk of injury, read owner's manual care fully before using. © 2005 NT+E Co. 800 -270-0810 WARNING Par ...

  • Northern Industrial Tools M157300E - page 7

    Machine Component Identification 7 I.) Unpack Your pressure washer is shipped in one box. Separate and identify the components found in both boxes. Pressure Hose Any Questions, Comments, Problems or Parts Orders Call NorthStar Customer Service 1-800-270- 0810 * Figures shown are for representation only. Actual components will vary by model. ...

  • Northern Industrial Tools M157300E - page 8

    Machine Component Identification 8 II.) Hardware Bag Hose Hook – Qty 3 Part # 38510 Gun Hook – Qty 2 Part # 38509 Flange Nut – Qty 8 Part # 82019 Carriage Bolt - Qty 2 Part # 82233 T-Handle – Qty 2 Part # 38578 Grommet – Qty 5 Part # 35198 Nozzle – Qty 2 Part # 778150 Washer – Qty 2 Part # 82021 Lock Nut – Qty 2 Part # 82013 ...

  • Northern Industrial Tools M157300E - page 9

    Machine Component Identification 9 nozzles grommets gun hooks flange nuts hose hook handle Hook Detail flange nut Top Hook Detail Lock Nut and Washer t-handle knob carriage bolt III.) Handle Assembly 1.) Attach handle to base with two carriage bolts and t-handle knobs. 2.) Spin a flange nut backwards onto two hose hooks and each gun hook. (see hook ...

  • Northern Industrial Tools M157300E - page 10

    Machine Component Identification 10 1.) Handle . Designed for easy cart movement. 2.) Hose Hook . Store hose on hook. 3.) Pressure Hose. Attach quick couplers to gun and water outlet. 4.) Chemical Hose. Submerge in cleaning solution. 5.) Water Pump. Inspect for loose/broken parts prior to each use. 6.) Motor. Leeson motor provides years of reliable ...

  • Northern Industrial Tools M157300E - page 11

    Pump Component Identification 11 Operation Instructions Water Supply 1.) Make sure the water supply is clean. Debris can cause excess pump wear and reduce performance. 2.) An insufficient water supply wil l damage your pump. Make sure the water supply is steady and is 20% over the rated flow of your pump. Use a stopwatch to time how long it takes t ...

  • Northern Industrial Tools M157300E - page 12

    Operation Instructions 12 START-UP INSTRUCTIONS 1. Attach garden hose. 2. Attach pressure hose. 3. Attach gun and lance. 4. Turn water supply ON. 5. Squeeze trigger to purge air from pump. 6. Insert nozzle. 7. Plug in power cord 8. Reset the GFCI button on the cord 9. Start motor. SHUT-DOWN INSTRUCTIONS 1. Turn motor OFF. 2. Unplug the power cord. ...

  • Northern Industrial Tools M157300E - page 13

    Operation Instructions 13 Spray Gun Safety Lock When not spraying, use the spray gun safety lock to prevent accidental high pressure discharge. Attaching the Lance Tighten spin-on coupler hand tight. Note: The o-rings make the seal so there is no need to ti ghten with a wrench. spray gu n spray gun safety loc k lance spin-on coupler ...

  • Northern Industrial Tools M157300E - page 14

    Operation Instructions 14 Flying objects. Make sure nozzle is secure before sque ezing trig ger. If nozzle is not secure it will become a projectile. Serious injury can occur. WARNING Installing Nozzles To install a nozzle pull back the collar and push the nozzle into the coupler. Once the connection is made, pull on the nozzle to make sure it is s ...

  • Northern Industrial Tools M157300E - page 15

    Operation Instructions 15 Applying Chemicals 1.) Install the black nozzle when applying chemicals onto the cleaning surface. 2.) Start the pressure washer acco rding to the start-up instructions. 3.) Submerge the chemical hos e in cleaning solution. 4.) Squeeze the spray gun trigger. The chemical in jector will draw the chemical into the water stre ...

  • Northern Industrial Tools M157300E - page 16

    Maintenance and Storage 16 Maintenance Mode Before performing any maintenance on the pressure washer, it must be placed in maintenance mode. 1.) Turn off motor and unplug cord. 2.) Turn off water supply. 3.) Squeeze trigger to relieve system pressure. Maintenance Schedule What to Check When To Check What to Do Inlet Filter Each Use Visually inspect ...

  • Northern Industrial Tools M157300E - page 17

    Maintenance and Storage 17 sight glass drain plug fill cap Cat 3DX25GSI Pump fill cap Comet BXD 1617E Pump Oil capacity: 4.3oz. (.13L) Oil capacity: 8.5 oz. (.25L) FIG01854 Oil capacity: 8.5 oz. (.25L) drain plug sight glass fill cap Cat 2DX20ES Pump drain plug sight glass Pump Oil Change 1.) Place a suitable container below the pump to catch the u ...

  • Northern Industrial Tools M157300E - page 18

    Maintenance and Storage 18 Winter Storage Protect your pump, hose and gun from freezing. Items needed: 12” piece of garden hose or equivalent, funnel and RV antifreeze (approximately 6 oz.) 1.) Follow the storage inst ructions listed above. 2.) Make sure the motor start switch is OFF. 3.) Attach the garden hose with funnel to the pump inlet (see ...

  • Northern Industrial Tools M157300E - page 19

    Troubleshooting 19 Problem Motor will not start SOLUTION: A,B Low/Surging pressure or no wate r flow SOLUTION: C,D,E,F,G,H No chemical injectio n SOLUTION: I,J,K,L Cause Solution A- Tripped GFCI cord Reset GFCI cord B- Tripped motor relay Reset motor C- Insufficient water supply See water supply section of this manual D- Plugged pump inlet filter S ...

  • Northern Industrial Tools M157300E - page 20

    Specifications 20 157300 157301 PSI (bar) 1700 (117) PSI (bar) 2000 (138) GPM (l/min) 1.5 (5.7) GPM (l/min) 1.5 (5.7) Max Water Temp 140 ° F (60 ° C) Max Water Temp 140 ° F (60 ° C) Dimensions L x W x H 33.5” X 20.9” X 38.6” ( 851mm x 531mm x 980mm) Dimensions L x W x H 33.5” X 20.9” X 38.6” (851mm x 531mm x 980mm) Weight 95 lb (44k ...

  • Northern Industrial Tools M157300E - page 21

    Wiring Diagram 21 ...

  • Northern Industrial Tools M157300E - page 22

    Part Explosion M157300 Rev E 22 ITEM PART# DESCRIPTION QTY Models ITEM PART# DESCRIPTION QTY Models 1 38509 Thread ed Gun Hook 2 All 778128 Electric Control Box Cover 1 157300 2 778065 NorthStar Decal 1 All 23 778132 Electric Control Box Cover 1 157301,2 3 35198 7/16 ID Grommet 5 All 778140 GFCI Cord, 120V/15A 1 157300 4 778059 Handle 1 All 778141 ...

  • Northern Industrial Tools M157300E - page 23

    23 ...

Fabricant Northern Industrial Tools Catégorie Pressure Washer

Les documents que nous recevons du fabricant de l'appareilNorthern Industrial Tools M157300E peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Northern Industrial Tools
- manuels d’utilisations M157300E
- fiches produit Northern Industrial Tools
- dépliants
- ou étiquettes-énergie Northern Industrial Tools M157300E
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Northern Industrial Tools M157300E.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Northern Industrial Tools M157300E, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Northern Industrial Tools M157300E. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Northern Industrial Tools M157300E.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Northern Industrial Tools M157300E, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Northern Industrial Tools M157300E par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Northern Industrial Tools M157300E.

Le manuel d’utilisation complet Northern Industrial Tools, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Northern Industrial Tools M157300E - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Northern Industrial Tools M157300E, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lNorthern Industrial Tools M157300E qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Northern Industrial Tools M157300E - qui devraient nous aider dans les premières étapes lors de l'utilisation Northern Industrial Tools M157300E
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Northern Industrial Tools M157300E
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Northern Industrial Tools M157300E dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Northern Industrial Tools M157300E?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Northern Industrial Tools M157300E, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Northern Industrial Tools M157300E il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)