Français dropdown-ico

Manuel d’utilisation Delta 36-953

32 pages 3.94 mb
Télécharger

Aller à la page of 32

Summary
  • Delta 36-953 - page 1

    INSTRUCTION MANUAL P ART NO. 422-40-651-0013 - 01-24-05 Copyright © 2005 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). UNISA W ® 10" Left Tilting Arbor Saw (Model 36-953) ...

  • Delta 36-953 - page 2

    2 T ABLE OF CONTENTS Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to r educe the risk of personal injury . Improper operation, maintenance or modification of tools or equipment could r esult in serious injury and prop ...

  • Delta 36-953 - page 3

    3 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury . Used without the saf ...

  • Delta 36-953 - page 4

    4 GENERAL SAFETY RULES READ AND UNDERST AND ALL WARNINGS AND OPERA TING INSTRUCTIONS BEFORE USING THIS EQUIPMENT . Failure to follow all instructions listed below , may result in electric shock, fire, and/or serious personal injury or pr operty damage. IMPORT ANT SAFETY INSTRUCTIONS 1. FOR YOUR OWN SAFETY , READ THE INSTRUCTION MANUAL BEFORE OPERA ...

  • Delta 36-953 - page 5

    5 ADDITIONAL SAFETY RULES FOR T ABLE SA WS 1 . DO NOT OPERA TE THIS MACHINE until it is assembled and installed according to the instructions. 2. OBT AIN ADVICE FROM YOUR SUPERVISOR, instructor , or another qualified person if you are not familiar with the operation of this machine. 3. FOLLOW ALL WIRING CODES and recommended electrical connections. ...

  • Delta 36-953 - page 6

    6 A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cor ds which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s plug. Before connec ...

  • Delta 36-953 - page 7

    7 EXTENSION CORDS Use proper extension cor ds. Make sure your extension cor d is in good condition and is a 3-wire extension cord which has a 3-pr ong grounding type plug and matching r eceptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine. An undersized ...

  • Delta 36-953 - page 8

    Fig. 1 1. Unisaw 2. Switch (shown with a GPE switch) Fig. 2 3. Extension wing 4. Handwheel 5. Blade guar d and splitter assembly 6. Upper bracket for splitter 7. Lower bracket for support r od 8. Support r od 9. 7/8" Open end arbor wr ench 10. 7/8"x1/2" Closed end arbor wrench 11. Dust chute 12. Miter gage 13. Cap for miter gage hand ...

  • Delta 36-953 - page 9

    9 UNP ACKING AND CLEANING Carefully unpack the machine and all loose items fr om the shipping container(s). Remove the protective coating fr om all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces ...

  • Delta 36-953 - page 10

    10 Fig. 4 Fig. 5 Fig. 6 ASSEMBLING EXTENSION WING NOTE: CHECK TO SEE WHA T TYPE OF ST ARTER BOX WAS SHIPPED WITH YOUR SA W (GPE OR L VC). A GPE ST ARTER HAS ROUND “ON” AND “OFF” BUTTONS. A L VC ST ARTER HAS RECT ANGLE “ON” AND “OFF” BUTTONS. NOTE FOR GPE ST AR TER BOX: If your Unisaw was shipped with an GPE starter box, the GPE “O ...

  • Delta 36-953 - page 11

    11 ASSEMBLING L VC ST ARTER BOX TO CABINET If you purchased the machine with magnetic push button electrical controls, the saw is shipped with the starter box completely wired to the switch and motor . However , the starter box must be mounted to the saw cabinet. T o assemble the starter box (A) Fig. 7, to the saw cabinet, proceed as follows: 1. Pl ...

  • Delta 36-953 - page 12

    12 ASSEMBLING GPE ON/OFF SWITCH 1. Locate the GPE switch and har dware that was removed in the section “ASSEMBLING EXTENSION WING.” 2. Loosely assemble switch and switch bracket (A) Fig. 12, to the inside front lip of extension wing. Insert a 5/16- 18x1" flat head screw (D) thr ough hole (G), place a 5/16" flat washer (E) on screw and ...

  • Delta 36-953 - page 13

    13 Fig. 16 Fig. 17 Fig. 19 Fig. 18 Fig. 20 Fig. 21 4. If an adjustment is necessary , loosen two screws (F) Fig. 17, and adjust splitter bracket (A) until it is aligned with the inside blade flange (B) Fig. 15. Tighten two screws (F). Loosely assemble scr ew and fastener plate (C), which were r emoved in STEP 2. 5. Insert thr eaded end of support r ...

  • Delta 36-953 - page 14

    14 Fig. 22 Fig. 23 Fig. 25 Fig. 24 Fig. 26 Fig. 27 5/16" lockwasher , then a 5/16" flat washer , onto a 5/16- 18x1" hex head screw (N), insert the scr ew (N) through the hole in the upper splitter bracket (M) and thread the screw into the lower splitter bracket (L). NOTE: Do not tighten screw (N) at this time. 9. Insert the fr ont en ...

  • Delta 36-953 - page 15

    15 Fig. 28 Fig. 30 Fig. 29 A TT ACHING MOTOR COVER NOTE: IF YOU HA VE AN “L VC” (ST ARTER BOX) VERSION UNISAW , YOU WILL HA VE TO A TT ACH TWO BOTTOM SPRING CLIPS TO THE MOTOR COVER. IF YOU HA VE AN “GPE” (ST ARTER BOX) VERSION UNISAW THE SPRING CLIPS ARE ALREADY A TT ACHED TO THE MOTOR COVER. 1. Attach the two motor cover clips to the moto ...

  • Delta 36-953 - page 16

    16 Fig. 36 ASSEMBLING RIP FENCE HOLDER BRACKETS Assemble the rip fence holder brackets (A) and (B) Fig. 37, to the four holes located in the right hand side of the saw cabinet using four #10 x 1/2" sheet metal screws supplied. Fig. 38 Fig. 37 A B ASSEMBLING DUST CHUTE ADAPTER The Unisaw is supplied with a dust chute connector to provide a mean ...

  • Delta 36-953 - page 17

    17 Fig. 39 A B Fig. 40 A BLADE RAISING MECHANISM The saw blade is raised and lowered with the fr ont handwheel (A) Fig. 41. With the exception of hollow ground blades, the blade should be raised 1/8" to 1/4" above the top surface of the material being cut. With hollow ground blades, the blade should be raised the maximum to provide gr eat ...

  • Delta 36-953 - page 18

    18 ADJUSTING 90 AND 45 DEGREE POSITIVE STOPS Positive stops are pr ovided to quickly and accurately position the blade at 90 and 45 degrees to the table. T o check and adjust the positive stops, proceed as follows: DISCONNECT MACHINE FROM POWER SOURCE. 1. Raise the saw blade all the way to the top and turn the blade tilting handwheel clockwise as f ...

  • Delta 36-953 - page 19

    19 ADJUSTING T ABLE INSER T Place a straight edge (B) across the table at both ends of the table insert as shown in Fig. 46. The table insert (A) should always be level with the table. If an adjustment is necessary , turn the adjusting screws (C), as needed, with allen wrench supplied. NOTE: THE MITER GAGE HANDLE CAN BE USED TO STORE THE ALLEN WREN ...

  • Delta 36-953 - page 20

    20 REPLACING BEL TS AND ADJUSTING BEL T TENSION DISCONNECT MACHINE FROM POWER SOURCE. 1. Remove motor cover to gain access to the motor . 2. Place a block of wood (C) Fig. 51, between the motor and saw cabinet as shown. NOTE: It may be necessary to raise the saw arbor in order to insert the wooden block. Lower the saw arbor until the motor contacts ...

  • Delta 36-953 - page 21

    21 Fig. 54 Fig. 55 C A B MACHINE USE COMMON SAWING OPERA TIONS Common sawing operations include ripping and crosscutting plus a few other standar d operations of a fundamental nature. As with all power machines, ther e is a certain amount of hazard involved with the operation and use of the machine. Using the machine with the respect and caution de ...

  • Delta 36-953 - page 22

    WHEN USING YOUR UNIFENCE AS A CUT -OFF GAGE, MAKE SURE IT IS PROPERL Y SET UP AS DESCRIBED HERE. The Unifence can be used as a cut-off gage when cr oss cutting a number of pieces to the same length. When using the unifence as a cut-off gage, it is very important that the rear end of the fence be positioned so the work piece is clear of the fence be ...

  • Delta 36-953 - page 23

    23 Fig. 61A Fig. 61 table, after which the work is lifted and brought along the outside edge of the fence. The cut-off stock remains on the table and is not touched until the saw blade has stopped, unless it is a lar ge piece allowing safe removal. When ripping boar ds longer than three feet, use a work support at the rear of the saw to keep the wo ...

  • Delta 36-953 - page 24

    24 Fig. 64 H G A B Fig. 67 Fig. 65 Fig. 66 W H Moulding is cutting a shape on the edge or face of the work. Cutting mouldings with a moulding cutterhead is a fast, safe and clean operation.The many differ ent knife shapes available make it possible for the operator to produce almost any kind of mouldings, such as various styles of corner moulds, pi ...

  • Delta 36-953 - page 25

    25 C Fig. 68 SPECIAL A TTENTION SHOULD BE GIVEN THE GRAIN DIRECTION. MAKE ALL CUTS IN THE SAME DIRECTION AS THE GRAIN WHENEVER POSSIBLE. AL WA YS INST ALL BLADE GUARD AFTER OPERA TION IS COMPLETE. Fig. 69 Fig. 70 Fig. 71 A B C 1. Dadoing is cutting a rabbet or wide groove into the work. Most dado head sets are made up of two outside saws and four o ...

  • Delta 36-953 - page 26

    Fig. 74 Fig. 75 Kerf should be about 1/4" apart. 26 3. Fig. 73, shows a typical dado operation using the miter gage as a guide. NEVER USE THE DADO HEAD IN A BEVEL POSITION. AL WA YS INST ALL BLADE GUARD AFTER OPERA TION IS COMPLETED. Fig. 74, illustrates dimensions for making a typical featherboard. The material which the featherboar d is cons ...

  • Delta 36-953 - page 27

    27 PUSH STICK MAKE FROM 1/2" OR 3/4" WOOD OR THICKNESS LESS THAN WIDTH OF MA T’L. TO BE CUT CUT OFF HERE TO PUSH 1/4" WOOD CUT OFF HERE TO PUSH 1/2" WOOD NOTCH TO HELP PREVENT HAND FROM SLIPPING 1/2" SQUARES CONSTRUCTING A PUSH STICK When ripping work less than 4 inches wide, a push stick should be used to complete the fe ...

  • Delta 36-953 - page 28

    28 TROUBLESHOOTING For assistance with your machine, visit our website at www .deltamachinery .com for a list of service centers or call the DEL T A Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582). MAINTENANCE P AR TS, SERVICE OR WARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standard ...

  • Delta 36-953 - page 29

    29 A complete line of accessories is available from your Delta Supplier , Porter -Cable • Delta Factory Service Centers, and Delta Authorized Service Stations. Please visit our W eb Site www .deltamachinery .com for a catalog or for the name of your nearest supplier . Since accessories other than those offer ed by Delta have not been tested with ...

  • Delta 36-953 - page 30

    30 T wo Y ear Limited New Product W arranty Delta will repair or r eplace, at its expense and at its option, any new Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, pr ovided that the customer returns the product prepaid to a Delta factory service center or authorized serv ...

  • Delta 36-953 - page 31

    31 NOTES ...

  • Delta 36-953 - page 32

    The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas registradas de POR TER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T ...

Fabricant Delta Catégorie Saw

Les documents que nous recevons du fabricant de l'appareilDelta 36-953 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Delta
- manuels d’utilisations 36-953
- fiches produit Delta
- dépliants
- ou étiquettes-énergie Delta 36-953
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Delta 36-953.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Delta 36-953, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Delta 36-953. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Delta 36-953.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Delta 36-953, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Delta 36-953 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Delta 36-953.

Le manuel d’utilisation complet Delta, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Delta 36-953 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Delta 36-953, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lDelta 36-953 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Delta 36-953 - qui devraient nous aider dans les premières étapes lors de l'utilisation Delta 36-953
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Delta 36-953
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Delta 36-953 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Delta 36-953?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Delta 36-953, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Delta 36-953 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)