Français dropdown-ico

Manuel d’utilisation Regency IG34-NG

32 pages 2.03 mb
Télécharger

Aller à la page of 32

Summary
  • Regency IG34-NG - page 1

    PLEASE KEEP THESE INSTR UCTIONS FOR FUTURE REFERENCE Models: IG34-NG IG34-LPG IG34-ULPG Owner s & Installation Man ual 04/28/09 LISTINGS AND CODE APPROV ALS These gas appliances have been tested in accordance with AS4553, NZS 5262 and have been certi fi ed by the Australian Gas Association for installation and operation as described in these I ...

  • Regency IG34-NG - page 2

    2 Regency IG34 Gas Inbuilt Fireplace REGENCY GAS INBUIL T FIREPLACE TO THE NEW OWNER Congratulations! Y ou are the owner of a state-of-the-art Gas Inbuilt Fireplace by FPI. The Regency Gas Fireplace Series of appliances has been designed to provide you with all the warmth and charm of a fi replace, at the fl ick of a switch. The model IG34 of thi ...

  • Regency IG34-NG - page 3

    3 Regency IG34 Gas Inbuilt Fireplace T ABLE OF CONTENTS DA T A BADGE Copy of Data Badge ..................................................... 4 INST ALLA TION Important Message ........................................................ 5 For Y our Safety .............................................................. 5 Before Y ou Start .............. ...

  • Regency IG34-NG - page 4

    4 Regency IG34 Gas Inbuilt Fireplace DA T A BADGE (Australia Only) This is a copy of the label that accompanies each Regency IG34 Gas Inbuilt fi replace. We have printed a copy of the contents here for your review . DA T A BADGE NOTE: Regency units are constantly being improved. Check the label on the unit and if there is a difference, the label o ...

  • Regency IG34-NG - page 5

    5 Regency IG34 Gas Inbuilt Fireplace INST ALLA TION IMPORT ANT MESSAGE The Regency Gas Inbuilt must be installed in accordance with these instructions. Carefully read all the instructions in this manual fi rst. Note: Failure to follow these instructions could cause a malfunction of the heater which could result in death, serious bodily injury , an ...

  • Regency IG34-NG - page 6

    6 Regency IG34 Gas Inbuilt Fireplace INST ALLA TION Mantel Clearances Note: A non-combustible mantel may be installed at a lower height if the fram- ing is made of metal studs covered with a non-combustible board. CLEARANCES T O COMBUSTIBLES Minimum Clearances to Combustibles From Unit Sides A 10" / 255mm Ceiling B 47.5" / 1205mm Mantel C ...

  • Regency IG34-NG - page 7

    7 Regency IG34 Gas Inbuilt Fireplace INST ALLA TION GAS PIPE PRESSURE TESTING The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig. (3.45 kPa). Disconnect piping from valve at press ...

  • Regency IG34-NG - page 8

    8 Regency IG34 Gas Inbuilt Fireplace INST ALLA TION INST ALLA TION IN MASONR Y OR ZERO CLEARANCE CHIMNEY 1) Measure and record dimensions to determine total Flex Liner length requirements (see instructions below for details). 2) Carefully feed the liner down the chimney (masonry or zero clearance) and out through the damper . One person should feed ...

  • Regency IG34-NG - page 9

    9 Regency IG34 Gas Inbuilt Fireplace AERA TION SETTINGS The burner aeration is factory set but may need adjusting due to either the local gas supply , air supply or altitude. This adjustment is performed by the installer . (Close the aeration for a more yellow fl ame, or open it to make the fl ame bluer). NG: 13mm open LPG: 13mm open ULPG: 13mm o ...

  • Regency IG34-NG - page 10

    10 Regency IG34 Gas Inbuilt Fireplace INST ALLA TION Conversion Kit #486-968 for NG to LPG Model THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION !! C onv ersion Kit 486-968 Contains: Q ty . Part # Description 1 904-345 Bur ner Orifi ce #51 1 918-273 Red "LPG" label 1 918-272 Label "Conv e ...

  • Regency IG34-NG - page 11

    11 Regency IG34 Gas Inbuilt Fireplace INST ALLA TION Installer Notice: These instructions must be left with the appliance. After carr ying out all adjustments , bloc k the setting screws with paint, taking care not to obstruct the breather or ifi ce of the pressure. Put back the modulator plastic cap . W ARNING: T o ensure the correct operation of ...

  • Regency IG34-NG - page 12

    12 Regency IG34 Gas Inbuilt Fireplace Conversion Kit #486-967 for NG to ULPG INST ALLA TION THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION !! C onv ersion Kit 486-967 Contains: Qty . Part # Description 1 904-345 Bur ner Orifi ce #53 1 918-273 Red "ULPG" label 1 918-272 Label "Conv er ted ...

  • Regency IG34-NG - page 13

    13 Regency IG34 Gas Inbuilt Fireplace INST ALLA TION Installer Notice: These instructions must be left with the appliance. After carr ying out all adjustments , bloc k the setting screw s with paint, taking care not to obstruct the breather or ifi ce of the pressure. Put back the modulator plastic cap . W ARNING: T o ensure the correct operation o ...

  • Regency IG34-NG - page 14

    14 Regency IG34 Gas Inbuilt Fireplace INST ALLA TION OPTIONAL ST AINLESS STEEL INNER P ANEL INST ALL Before you start: Stainless panels must be inspected f or scratches and dimples prior to installation. All claims to be recorded at this time. Claims for damage after installation will not receive consider ation. T o protect the fi nish during inst ...

  • Regency IG34-NG - page 15

    15 Regency IG34 Gas Inbuilt Fireplace INST ALLA TION LOG SET INST ALLA TION Read the instructions below carefully and refer to the diagrams. If logs are broken do not use the unit until they are replaced. Broken logs can interfere with the pilot operation. The gas log kit contains the following: a) 02-43 Rear Log b) 02-45 Front Right Log c) 02-56 M ...

  • Regency IG34-NG - page 16

    16 Regency IG34 Gas Inbuilt Fireplace INST ALLA TION Logs D)02-46 and E)02-47 in position. 6) Place the Left T op Log D)02-46 on the pin on Log C)02-56 and on top of the cutout on Log A)02-43. 7) Place the notch in Center Log E)02-47 over Log B)02- 45 and across the cutout on Log A)02-43. Cutout Pin Cutout Notch 8) Position notch in Front Right Log ...

  • Regency IG34-NG - page 17

    17 Regency IG34 Gas Inbuilt Fireplace INST ALLA TION 10) Place the embers and Rockwool on the exposed front burner tray . 9) Place Front Left Log G)02-44 onto the 2 front pins as shown. G)02-44 F)02-48 B)02-45 Bracket A)02-43 Front edge of rear burner The bottom right edge of Log F)02-48 must sit snugly against the bracket and the front edge of the ...

  • Regency IG34-NG - page 18

    18 Regency IG34 Gas Inbuilt Fireplace INST ALLA TION GLASS DOOR INST ALLA TION ST ANDARD FLUSH DOOR The standard fl ush door comes with a black frame. T o install the frame and glass door , simply hook the top door fl ange onto the top of the unit and swing the door towards the unit, diagram 1. Be careful that the glass gasket does not roll up; t ...

  • Regency IG34-NG - page 19

    19 Regency IG34 Gas Inbuilt Fireplace INST ALLA TION SCREEN INST ALLA TION Plinth Tri m Op tio n : Plinth Trim Kits are an option that can be used to fi nish off the installation when the bottom of the fi replace is higher than the hearth or to raise the fi replace. 1) Lay the faceplate side panels fl at, face down on something soft so they don ...

  • Regency IG34-NG - page 20

    20 Regency IG34 Gas Inbuilt Fireplace INST ALLA TION Note: Ensure that the fl anges on the sides of the fi rebox are on the outside, when installing the faceplate (see below). Faceplate Flange on fi rebox Door Frame Glass Door Metal Lip Openings on hinge 3) Fold down the 2 hinges on the bottom frame to a fl at position. The bottom frame is inst ...

  • Regency IG34-NG - page 21

    21 Regency IG34 Gas Inbuilt Fireplace INST ALLA TION Back of Faceplate Back of Faceplate Bracket Thermodisc 1) Install faceplate and door frame as per previous page. 2) After faceplate has been installed - place the touch pad (facing out) in the knockout located on the left side of the faceplate. 3) Secure with 2 screws as shown below . 4) T ake th ...

  • Regency IG34-NG - page 22

    22 Regency IG34 Gas Inbuilt Fireplace FINAL CHECK Before leaving this unit with the customer , the installer must ensure that the appliance is fi ring correctly . This includes: 1) Clocking the appliance to ensure the correct fi ring rate (rate noted on label) at 15 minutes. 2) If required, adjusting the primary air to ensure that the fl ame doe ...

  • Regency IG34-NG - page 23

    23 Regency IG34 Gas Inbuilt Fireplace OPERA TING INSTRUCTIONS OPERA TING INSTRUCTIONS Before operating this appliance, proceed through the following check list. 1) Read and understand these Instructions before operating this appliance. 2) Check to see that all wiring is correct and enclosed to prevent possible shock. 3) Check to ensure there are no ...

  • Regency IG34-NG - page 24

    24 Regency IG34 Gas Inbuilt Fireplace COPY OF LIGHTING INSTRUCTION PLA TE OPERA TING INSTRUCTIONS NORMAL OPERA TING SOUNDS OF GAS APPLIANCES It is possible that you will hear some sounds from your gas appliance. This is perfectly normal due to the fact that there are various gauges and types of steel used within your appliance. Listed below are som ...

  • Regency IG34-NG - page 25

    25 Regency IG34 Gas Inbuilt Fireplace MAINTENANCE CAUTION: ANY SAFETY SCREEN OR GUARD REMOVED FOR SERV - ICING AN APPLIANCE MUST BE REPLACED PRIOR TO OPERA T - ING THE APPLIANCE. CLOTHING OR OTHER FLAM- MABLE MA TERIAL SHOULD NOT BE PLACED ON OR NEAR THE APPLIANCE. DO NOT USE THIS APPLIANCE IF ANY P ART HAS BEEN UNDER W A TER. IMMEDIA TEL Y CALL AN ...

  • Regency IG34-NG - page 26

    26 Regency IG34 Gas Inbuilt Fireplace MAINTENANCE F AN MAINTENANCE T o Remove Fan: 1) Turn the unit off and allow it to cool to room temperature, 2) Unplug or disconnect power source to stove. 3) Open the bottom louvre. 4) Remove screws that secure protective screen. 5) Remove door frame and screen 6) Remove the ECS harness from the back clip. 7) P ...

  • Regency IG34-NG - page 27

    27 Regency IG34 Gas Inbuilt Fireplace MAINTENANCE 1) Unplug or disconnect the power source to the stove and shut off gas supply . 2) open bottom louvre and remove protective screen. 3) Remove the door frame and safety screen. 4) Remove the glass door, logs, and black or stainless inner liner , if installed. 5) Remove the rear log tray , burner and ...

  • Regency IG34-NG - page 28

    28 Regency IG34 Gas Inbuilt Fireplace P ARTS LIST ELECTRONIC COMPONENTS P ARTS LIST 910-936 910-082 910-088 910-089 910-084 910-527 910-935 910-080 910-521, 910-522, 910-523, 910-525 910-912 910-906 910-514 910-083 910-916 FG37 FG38 FG39 PG33 PG36 HG35 PG121/PG131 IG35 IG34 PG36D 910-909 Fan Resistor 910-936 Intermittent Pilot 910-082 Direct Spark ...

  • Regency IG34-NG - page 29

    29 Regency IG34 Gas Inbuilt Fireplace MAIN ASSEMBL Y Part # Description Part # Description 1) 910-169/P Fan Motor (240 V)** 2) 910-995 Thermodisc** 3) 486-968 LPG Conversion Kit** 486-967 ULPG Conversion Kit** 4) 336-574/P V alve Assembly - NG 336-576/P V alve Assembly - LPG 5) 910-080 SIGMA V alve 845 6) 336-001 V alve T ray Gasket** 7) 402-526 Gr ...

  • Regency IG34-NG - page 30

    30 Regency IG34 Gas Inbuilt Fireplace P ARTS LIST F ACEPLA TE ASSEMBL Y Part # Description 14) 336-914 Faceplate & T rim Complete - Regular 15) 366-942 Plinth Kit 16) 336-532 Flush Screen Door** *Not available as a replacement part. 14 15 ...

  • Regency IG34-NG - page 31

    31 Regency IG34 Gas Inbuilt Fireplace W ARRANTY Regency ® Fireplace Products are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance T eam carefully inspects each unit thoroughly before it leaves our door . Regency ® is pleased to extend this limited lifetime warranty to the original purchaser of a Regenc ...

  • Regency IG34-NG - page 32

    FIREPLACE PRODUCTS AUSTRALIA PTY . L TD. 21-23 SOUTH LINK, DANDENONG SOUTH VICTORIA, 3175 AUSTRALIA Printed in Canada © Copyright 2009, FPI Fireplace Products International Ltd. All rights reserved. ...

Fabricant Regency Catégorie Fire Pit

Les documents que nous recevons du fabricant de l'appareilRegency IG34-NG peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Regency
- manuels d’utilisations IG34-NG
- fiches produit Regency
- dépliants
- ou étiquettes-énergie Regency IG34-NG
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Regency IG34-NG.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Regency IG34-NG, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Regency IG34-NG. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Regency IG34-NG.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Regency IG34-NG, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Regency IG34-NG par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Regency IG34-NG.

Le manuel d’utilisation complet Regency, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Regency IG34-NG - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Regency IG34-NG, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lRegency IG34-NG qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Regency IG34-NG - qui devraient nous aider dans les premières étapes lors de l'utilisation Regency IG34-NG
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Regency IG34-NG
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Regency IG34-NG dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Regency IG34-NG?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Regency IG34-NG, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Regency IG34-NG il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)