-
CDA HN9610 - page 1
Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www .cda.eu hn9610 Induction Hob Manual for Installation, Use and Maintenance ...
-
CDA HN9610 - page 2
2 Important The CD A Group L td cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CD A reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance or use in a commercial environment. This appliance is no ...
-
CDA HN9610 - page 3
3 2004/108/EC. Parts intended to come into contact with food conform to 89/109/EC. IMPORT ANT INFORMA TION FOR CORRECT DISPOSAL OF THE PRODUCT IN A CCORD ANCE WITH EC DIRECTIVE 2002/96/EC. At the end of its working life, the product must be taken to a special local authority waste collection centre or to a dealer providing appliance recycling servi ...
-
CDA HN9610 - page 4
4 surface prior to use. • Do not modify the appliance in any way as this will invalidate the guarantee and is potentially dangerous. • The hob top is not designed for any use other than cooking: any other use (e.g. as a worktop) is potentially dangerous and will invalidate the guarantee. • This appliance must be connected to x ed wiring an ...
-
CDA HN9610 - page 5
5 capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. • Children shall not play with the appliance. • Cleaning and user maintenance shall not be made by children without supervision. • Metal objects such as knives ...
-
CDA HN9610 - page 6
6 divider must be made of material capable of withstanding 65°C above ambient temperature. • Never place inammable items or materials in a drawer or cupboard below the hob. Precautions in the event of an appliance fault • If a fault is noticed, switch o the appliance and turn o the electricity supply . • W arning: If the ceramic gla ...
-
CDA HN9610 - page 7
7 FOR THOSE WITH HEART P A CEMAKERS OR A CTIVE IMPLANTS: The function of this hob conforms to current electromagnetic interference standards and thus is in total compliance with legal requirements (2004/108/CE directives). T o avoid interference between your hob and a pacemaker , your pacemaker must be designed and programmed in compliance with the ...
-
CDA HN9610 - page 8
8 Using Y our Hob Zones: 1: Front left 1.85k W (3. 0kW boost) 180mm 2: Back left 1.85k W (3. 0kW boost) 180mm 3: Back right 1.85k W (3. 0kW boost) 180mm 4: Front right 2. 1k W (3. 7kW boost) 210mm 5: Centre 2. 1k W (3. 7k W boost) 210mm Fig. 1 4 3 1 2 5 ...
-
CDA HN9610 - page 9
9 Power level Type of cooking 0 Switched o 1/2 Melting (butter/chocolate) or keeping food warm 2/3 K eeping food hot or to heat small quantities of liquid 3/4 Heat larger quantities of liquid (sauces etc.) 4/5 Slow boiling, e.g spaghetti, soups, stews, potatoes 6/7 Gentle frying 7/8 Browning meats, frying sh, omelettes 9 Fast frying steaks Co ...
-
CDA HN9610 - page 10
10 Cooking on Induction The principle of induction cooking is based on magnetic eect. When you put your cookware on an induction zone and switch it on, the electronic boards in the hob produce induced currents in the base of the cookware and instantly raise its temperature. This heat is then transferred to the food inside the cookware. The best ...
-
CDA HN9610 - page 11
11 Using Y our Hob T o switch the hob on T o switch the power on, touch and hold the key for appro ximately two seconds. The hob will beep and all ve zone displays will show zero. Please note: If a power level is not set within ten seconds, the hob will switch o automatically . T o set the power level There are power level keys for each indiv ...
-
CDA HN9610 - page 12
12 Special Programmes The hob has two optional preset programmed heating levels for each of the zones. 42°C setting • T ouch the “Special Programmes” key so the special programmes control light illuminates. • Then touch either the “+” or “-” key for the zone you wish to maintain the 42°C temperature. T o cancel the special program ...
-
CDA HN9610 - page 13
13 L evel 2 • T ouch the “Booster” key twice so the booster control light ashes . • Then touch either the “+” or “-” key for the zone you wish to boost. The display for that zone will show “ ” alternating with “ ” . T o cancel the booster at any time, touch the “-” key for that zone. Note: The hob is fitted with a po ...
-
CDA HN9610 - page 14
14 • T o pause the hob, touch the “Pause” key , the hob displays “11” in all the zone displays. • T o restart cooking, touch the “Pause ” key again. Timer The hob is equipped with a timer that allows finish times to be set for the end of cooking on any combination of zones, between a minimum of one minute and a maximum of 99 minute ...
-
CDA HN9610 - page 15
15 • After appro ximately ve seconds, the “Zone timer indicator” will stop ashing and the countdown will start. • The timer display will show the minutes remaining. At the end of the timer , the selected zone will switch o and the hob will beep for appro ximately one minute. T o switch o the beep touch either of the “timer key ...
-
CDA HN9610 - page 16
16 K ey Lock The hob is equipped with a key lock to lock the controls. This can be used when the hob is o or during cooking. T o switch on the key lock T ouch the key for appro ximately two seconds until the LED above the key lock key illuminates and the hob beeps to confirm the key lock is switched on. T o switch o the key lock T ouch the k ...
-
CDA HN9610 - page 17
17 R esidual heat indicators The hob is equipped with residual heat indicators to warn when any of the zones are still hot to the touch after cooking. An “ H ” will show in the relevant zone display after cooking until the zone is at a safe temperature to touch. In the event of a power cut, the residual heat indictors will illuminate after the ...
-
CDA HN9610 - page 18
18 Ecient Use of Y our Hob The hob is equipped with zones of dierent sizes, designed to accommodate most shapes and sizes of pan. For best results, only use pans with at bottoms and choose an appropriate zone depending on the size of the pan. The most ecient use of the hob is shown below , where the pan and zone are correctly chosen. Us ...
-
CDA HN9610 - page 19
19 Care and Maintenance Always disconnect the appliance from the power supply before undertaking any cleaning or maintenance. Important: • S team cleaners must not be used when cleaning this appliance. • Y ou should use a non-abrasive cleaner to clean the hob top. Any abrasive cleaner (including Cif ) will scratch the surface and could erase th ...
-
CDA HN9610 - page 20
20 In the event of a fault with the hob, please advise CD A Customer Care of any fault code shown on the display Contact CD A Customer Care A: Customer Care Department, The CD A Group Ltd, Harby R oad, Langar , Nottinghamshire, NG13 9HY T: 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www .cda.eu T roubleshooting On rst use Y ou observe ...
-
CDA HN9610 - page 21
21 IMPORT ANT - PLEASE NOTE: In the event of any breakage , crack or cracking – even minimal – of the vitroceramic glass, immediately disconnect your appliance to prevent a risk of electric shock and contact CD A Customer Care. In use Y ou observe that Possible Causes What should you do ? One or all of the zones cuts out. The safety system has ...
-
CDA HN9610 - page 22
22 Fitting the Hob Unpacking the hob: T ake care not to lose or mishandle any parts. Fitting position of the hob: This appliance must be installed a minimum of 50mm from any back wall and a minimum of 180mm away from any adjacent vertical surfaces, e.g. a tall cupboard end panel. This may be reduced to 100mm if the adjacent surface is resistant to ...
-
CDA HN9610 - page 23
23 If tting a cooker hood above the hob: If a cooker hood is to be installed above the hob, the height of the hood above the hob must be at least 600mm (650mm is recommended) (Fig. 4). If the instructions supplied with the hood dictate that the hood must be installed at a height greater than 600mm, then that height is the minimum required. W all ...
-
CDA HN9610 - page 24
24 How to Install the Hob Overall dimensions of the hob: Width: 880 mm Depth: 520 mm W orktop cut-out dimensions: Width: 810 mm Depth: 490 mm 1. Make the required hole in the worktop. Before doing this, you must check the instructions supplied with any cooker hood to ensure that you will have the required clearance. The cut-out (Fig. 5) shows a 60m ...
-
CDA HN9610 - page 25
25 Mains Electricity Connection W arning! this appliance must be earthed W e recommend that the appliance is connected by a qualied electrician, who is a member of the N.I.C.E.I.C. and who will comply with the I.E. T . and local regulations. This hob is intended to be connected to permanent, fixing wiring by a double pole switch, having a conta ...
-
CDA HN9610 - page 26
26 • The inlet cable must be positioned so that it does not touch any of the hot parts of the hob or oven. Caution • This appliance must only be connected to a 230V ~ 50Hz network. • Observe the connection diagram. • The connection bo x is located underneath at the back of the hob casing. T o open the cover use a medium screwdriver . Insert ...
-
CDA HN9610 - page 27
27 Any service call arising from incorrect installation may result in a charge. CD A and its representatives cannot be held responsible for any matters resulting from incorrect connection, or related to either the absense of an earth connection or a faulty earth connection. ...
-
CDA HN9610 - page 28
Please contact our Customer Care Department for Service on the details below Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www .cda.eu ...
Avez-vous une question à propos de CDA HN9610?
Utiliser le formulaire ci-dessous
Si vous n’avez pas résolu votre problème avec CDA HN9610, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec CDA HN9610 il est probable qu’il a envie de partager la façon de le résoudre.