Français dropdown-ico

Manuel d’utilisation Hoshizaki KMD-450MWH

25 pages 3.67 mb
Télécharger

Aller à la page of 25

Summary
  • Hoshizaki KMD-450MWH - page 1

    Hoshizaki “A Superior Degree of Reliability” www .hoshizaki.com Models KMD-450MAH KMD-450MWH Modular Crescent Cuber Hoshizaki America, Inc. Issued: 1-19-2009 I N S T R U C T I O N M A N U A L ™ ...

  • Hoshizaki KMD-450MWH - page 2

     IMPORTANT Only qualied service technicians should install, service, or maintain this icemaker. No installation, service, or maintenance should be undertaken until the technician has thoroughly read this Instruction Manual. Likewise, the owner/manager should not proceed to operate the icemaker until the installer has instructed them on its pr ...

  • Hoshizaki KMD-450MWH - page 3

    3 IMPORTANT This manual should be read carefully before the icemaker is installed and operated. Only qualied service technicians should install, service, and maintain the icemaker. Read the warnings contained in this booklet carefully as they give important information regarding safety. Please retain this booklet for any further reference that m ...

  • Hoshizaki KMD-450MWH - page 4

    4 Important Safety Information Throughout this manual, notices appear to bring your attention to situations which could result in death, serious injury, or damage to the unit. WARNING Indicates a hazardous situation which could result in death or serious injury. CAUTION Indicates a situation which could result in damage to the unit. IMPORTANT Indic ...

  • Hoshizaki KMD-450MWH - page 5

    5 I. Specications A. Nameplate Rating 1. KMD-450MAH (self-contained air-cooled) See the nameplate for electrical and refrigeration specications. This nameplate is located on the rear panel. Since this nameplate is located on the rear panel of the icemaker, it cannot be read when the back of the icemaker is against a wall or against another pi ...

  • Hoshizaki KMD-450MWH - page 6

    6 2. KMD-450MWH (water-cooled) See the nameplate for electrical and refrigeration specications. This nameplate is located on the rear panel. Since this nameplate is located on the rear panel of the icemaker, it cannot be read when the back of the icemaker is against a wall or against another piece of kitchen equipment. Therefore, the necessary e ...

  • Hoshizaki KMD-450MWH - page 7

    7 B. Dimensions/Connections 1. KMD-450MAH Unit: mm [in.] Note: 5 [0.98] increases to 101. [3.98] when lower set of mounting holes is used. ...

  • Hoshizaki KMD-450MWH - page 8

    8 2. KMD-450MWH Unit: mm [in.] Note: 5 [0.98] increases to 101. [3.98] when lower set of mounting holes is used. ...

  • Hoshizaki KMD-450MWH - page 9

    9 II. Installation and Operating Instructions WARNING 1. This icemaker must be installed in accordance with applicable national, state, and local regulations. . CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after installation. Make sure that none have fallen into the dispenser unit/storage bin. A. Checks ...

  • Hoshizaki KMD-450MWH - page 10

    10 C. Location CAUTION 1. This icemaker is not intended for outdoor use. Normal operating ambient temperature should be within 45°F to 100°F (7°C to 38°C); Normal operating water temperature should be within 45°F to 90°F (7°C to 3°C). Operation of the icemaker, for extended periods, outside of these normal temperature ranges may affect i ...

  • Hoshizaki KMD-450MWH - page 11

    11 E. Bin Control Installation 1) Remove the  thumbscrews securing insulation panel (B), then remove insulation panel (B). See Fig. 3. ) Disconnect the discharge hose, the drain valve drain hose, and the overow drain hose. 3) Disconnect the pump motor connector and the oat switch connector from the side of the control box. 4) Remove the ...

  • Hoshizaki KMD-450MWH - page 12

    1 11) Reconnect the pump motor connector and the oat switch connector. 1) Replace insulation panel (B) in its correct position and secure with the  thumbscrews. 13) Replace insulation panel (A), the top insulation, and the exterior panels in their correct positions. F. Electrical Connection WARNING 1. Electrical connection must be hard- ...

  • Hoshizaki KMD-450MWH - page 13

    13 G. Water Supply and Drain Connections See Fig. 7, 8, or 9 WARNING 1. Water supply and drain connections must be installed in accordance with applicable national, state, and local regulations. . Normal operating water temperature should be within 45°F to 90°F (7°C to 3°C). Operation of the icemaker, for extended periods, outside of this ...

  • Hoshizaki KMD-450MWH - page 14

    14 1. Icemaker • Icemaker water supply inlet is 1/" female pipe thread (FPT). A minimum of 3/8" OD copper tubing is recommended for the icemaker water supply line. • An icemaker water supply line shut-off valve and drain valve should be installed. • Icemaker drain outlet is 3/4" FPT. A minimum of 3/4" OD hard pipe is re ...

  • Hoshizaki KMD-450MWH - page 15

    15 Icemaker Drain Outlet 3/4" FPT Icemaker Water Supply Inlet 1/" FPT Fig. 8 Condenser Water Supply Inlet 1/" FPT Condenser Drain Outlet 1/" FPT KMD-450MWH Connection to an Open Drain System Separate piping to approved drain. Leave a two-inch (5 cm) vertical air gap between the end of each pipe and the drain. Icemaker B ...

  • Hoshizaki KMD-450MWH - page 16

    16 Condenser Return Line Shut-Off Valve Condenser Return Line Drain Valve Icemaker Drain Outlet 3/4" FPT Icemaker Water Supply Inlet 1/" FPT Condenser Water Supply Inlet 1/" FPT Condenser Return Outlet 1/" FPT Separate piping to approved drain. Leave a two-inch (5 cm) vertical air gap between the end of each pipe and th ...

  • Hoshizaki KMD-450MWH - page 17

    17 H. Final Checklist WARNING CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after installation. Make sure that none have fallen into the dispenser unit/storage bin. 1) Is the icemaker level? ) Is the icemaker in a site where the ambient temperature is within 45°F to 100°F (7°C to 38°C) and the water ...

  • Hoshizaki KMD-450MWH - page 18

    18 I. Startup WARNING 1. All parts are factory-adjusted. Improper adjustments may adversely affect safety, performance, component life, and warranty coverage. . If the icemaker is turned off, wait for at least 3 minutes before restarting the icemaker to prevent damage to the compressor. 3. To prevent damage to the water pump, do not leave the co ...

  • Hoshizaki KMD-450MWH - page 19

    19 III. Cleaning and Maintenance WARNING CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after any cleaning or maintenance is done to the unit. Make sure that none have fallen into the dispenser unit/storage bin. A. Cleaning and Sanitizing Instructions Hoshizaki recommends cleaning and sanitizing this unit at ...

  • Hoshizaki KMD-450MWH - page 20

    0 8) In bad or severe water conditions, clean the oat switch as described below. Otherwise, continue to step 9. a. Remove the  thumbscrews securing insulation panel (B), then remove insulation panel (B). See Fig. 10. b. Disconnect the discharge hose, the drain valve drain hose, and the overow drain hose. c. Disconnect the pump motor con ...

  • Hoshizaki KMD-450MWH - page 21

    1 17) Turn off the power supply, then remove the front panel. 18) Move the control switch to the "ICE" position. 19) Replace the front panel in its correct position. 0) Turn on the power supply to ll the water tank with water. 1) Turn off the power supply after 3 minutes. ) Remove the front panel. 3) Move the service ...

  • Hoshizaki KMD-450MWH - page 22

     15) Replace the front panel in its correct position. 16) Clean the dispenser unit/storage bin liner using a neutral cleaner. Rinse thoroughly after cleaning. 17) Turn on the power supply to start the automatic icemaking process. B. Maintenance This icemaker must be maintained individually, referring to the instruction manual and labels provi ...

  • Hoshizaki KMD-450MWH - page 23

    3 C. Preparing the Icemaker for Long Storage CAUTION 1. When storing the icemaker for an extended time or in sub-freezing temperatures, follow the instructions below to prevent damage. . To prevent damage to the water pump, do not leave the control switch in the "SERVICE" position for extended periods of time when the water tank is ...

  • Hoshizaki KMD-450MWH - page 24

    4 3) Open the condenser water supply line drain valve. If connected to a closed loop system, also open the condenser return line drain valve. 4) Attach a compressed air or carbon dioxide supply to the condenser water supply line drain valve. 5) Open the water regulating valve by using a screwdriver to pry up on the spring retainer underneath the ...

  • Hoshizaki KMD-450MWH - page 25

    5 HOSHIZAKI AMERICA, INC. 618 Hwy . 74 S., Peachtree City , GA 30269 USA TEL (770) 487-2331 F AX (770) 487-3360 www .hoshizaki.com 91A7BA10A ...

Fabricant Hoshizaki Catégorie Ice Maker

Les documents que nous recevons du fabricant de l'appareilHoshizaki KMD-450MWH peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Hoshizaki
- manuels d’utilisations KMD-450MWH
- fiches produit Hoshizaki
- dépliants
- ou étiquettes-énergie Hoshizaki KMD-450MWH
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Hoshizaki KMD-450MWH.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Hoshizaki KMD-450MWH, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Hoshizaki KMD-450MWH. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Hoshizaki KMD-450MWH.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Hoshizaki KMD-450MWH, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Hoshizaki KMD-450MWH par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Hoshizaki KMD-450MWH.

Le manuel d’utilisation complet Hoshizaki, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Hoshizaki KMD-450MWH - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Hoshizaki KMD-450MWH, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lHoshizaki KMD-450MWH qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Hoshizaki KMD-450MWH - qui devraient nous aider dans les premières étapes lors de l'utilisation Hoshizaki KMD-450MWH
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Hoshizaki KMD-450MWH
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Hoshizaki KMD-450MWH dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Hoshizaki KMD-450MWH?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Hoshizaki KMD-450MWH, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Hoshizaki KMD-450MWH il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)