Français dropdown-ico

Manuel d’utilisation Mackie PPM1008

32 pages 4.59 mb
Télécharger

Aller à la page of 32

Summary
  • Mackie PPM1008 - page 1

    OWNER’S MANUAL FOOT SWITCH FX / 2 X 800W PROFESSIONAL POWERED MIXER PPM1008 8-Channel, 2 x 800 W Pr ofessional Po wered M ix er ...

  • Mackie PPM1008 - page 2

    2 PPM1008 PPM1008 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’ s instructions. 8. Do not install near any heat sources such as ...

  • Mackie PPM1008 - page 3

    3 Owner’ s Manual Owner’ s Manual Part No. SW0685 Rev . A ©2008 LOUD T echnologies Inc. All Rights Reserved. Episode 3: The Mackie marketing department landing party arrives on Aldebaran 3 to investigate a distress signal, with hilarious r esults. Ready , steady , g o! 1. T urn the channel level, mon 1, and FX/mon 2 controls fully down. 2. T u ...

  • Mackie PPM1008 - page 4

    4 PPM1008 PPM1008 Introduction It is possible that only one person will read this manual all the way through. Hello mom. Here's another manual from your boy . Thank you for choosing a Mackie professional pow- ered mixer . These powerful mixers are designed to meet the needs of almost any small to medium-sized club, meeting room, sanctuary , or ...

  • Mackie PPM1008 - page 5

    5 Owner’ s Manual Owner’ s Manual Need help with y our new mixer? • Visit www .mackie.com and click Support to fi nd: F A Qs, manuals, addendums, and user forums. • Email us at: t echmail@mackie.com. • T elephone 1-800-898-3 211 to speak with one of our splendid technical support chaps, (Monda y through Frida y , from 7 a.m. t o 5 p.m. P ...

  • Mackie PPM1008 - page 6

    6 PPM1008 PPM1008 Hookup Diagrams Club System This diagram shows microphones attached to channels 1 and 2, electric guitars connected directly to channels 5 and 6 (with hi-z switch pressed in), and a keyboard attached to channel 7's stereo inputs. A portable recorder is attached to the stereo tape outputs to record the per formance. Mackie SRM ...

  • Mackie PPM1008 - page 7

    7 Owner’ s Manual Owner’ s Manual House of W or ship System This diagram shows microphones attached to the mic inputs of channels 1 to 4, an electric guitar con- nected directly to channel 5 (with hi-z switch pressed in), an acoustic guitar mic connected to channel 6 mic in, a keyboard attached to channel 7's stereo inputs, and a drum mach ...

  • Mackie PPM1008 - page 8

    8 PPM1008 PPM1008 DJ System This diagram shows a wireless microphone receiver connected to the channel 1 line input, a graphic EQ connected to channel 1's insert jack (to help control feedback in the wireless mic), a microphone con- nected to channel 2, and an iPod docking station attached to channel 8's RCA inputs. A Mackie d.2 Pro DJ pr ...

  • Mackie PPM1008 - page 9

    9 Owner’ s Manual Owner’ s Manual Large Band System This diagram shows microphones attached to the mic inputs of channels 1 to 4, electric guitars con- nected directly to ch. 5 and 6 (with hi-z switches pressed in), a guitar processor connected to ch.6 insert, a keyboard attached to channel 7's stereo inputs, and an electronic drum kit att ...

  • Mackie PPM1008 - page 10

    10 PPM1008 PPM1008 OUTPUT POWER: @ 4 OHMS, 800 WATTS PEAK PER CH MINIMUM LOAD: 4 OHMS PER CHANNEL 2 X 800W PROFESSIONAL POWERED MIXER Rear Panel Features 1. POWER CONNECTION This jack accepts the supplied 3-prong IEC AC power cord. Before you plug the AC power cord into the powered mixer , make sure that the voltage of your unit is the same voltage ...

  • Mackie PPM1008 - page 11

    11 Owner’ s Manual Owner’ s Manual • 1/4" TS outputs are wir ed Tip positive, and Sleeve negative. 1/4" TS Connection These two types of outputs are wir ed in parallel, and it is possible to use both types at once. The minimum impedance that the powered mixers can handle is 4 ohms per channel, and we recommend that you do not go bel ...

  • Mackie PPM1008 - page 12

    12 PPM1008 PPM1008 Front Panel Features 7. MIC INPUTS W e use phantom-powered, balanced microphone inputs just like the big studio mega-consoles, for exactly the same reason: This kind of circuit is excellent at rejecting hum and noise. Y ou can plug in almost any kind of mic that has a standard XLR-type male mic con- nector . Professional ribbon, ...

  • Mackie PPM1008 - page 13

    13 Owner’ s Manual Owner’ s Manual 12. INSERT (CH. 1 to 6) These unbalanced 1/4" jacks on channels 1 to 6 are for connecting serial effects processors such as compres- sors, equalizers, de-essers, or fi lters. The insert point is after the gain switch [32] and compressor circuits (on channels 1 – 4), but before the channel’ s EQ and l ...

  • Mackie PPM1008 - page 14

    14 PPM1008 PPM1008 15. FX/MON 2 SEND OUTPUT This 1 / 4 " TRS line-level output can be used to feed an external effects processor (FX) or another set of stage monitors (mon 2). The output here is a copy of what goes into the internal FX processor , being the careful mix of all channels whose FX/mon 2 control [22] is turned more than minimum. Th ...

  • Mackie PPM1008 - page 15

    15 Owner’ s Manual Owner’ s Manual EFFECTS: SERIAL OR P ARALLEL? “Serial” means that the entire channel signal leaves the mixer (insert [12] send), is routed through the effects device, and returns to the mixer (insert return). Examples: compressor , limiter , graphic equalizer . Line-level sources can also be patched through a serial effec ...

  • Mackie PPM1008 - page 16

    16 PPM1008 PPM1008 Channel Controls The eight vertical channel strips look very similar , with only a few differences between them. Each chan- nel works independently , and just controls the signals plugged into the inputs directly below it. Mono Channels 1 to 6 • Channels 1 to 6 are mono channels, and their controls affect either the mono mic in ...

  • Mackie PPM1008 - page 17

    17 Owner’ s Manual Owner’ s Manual 21. MON 1 This control allows you set up a nice monitor mix, independent of the main mix or the monitor 2 mix. Adjust these controls on each channel until your band is happy with the stage monitor mix. The controls are off when turned fully down, deliver unity gain at the center detent, and can provide up to 1 ...

  • Mackie PPM1008 - page 18

    18 PPM1008 PPM1008 32. GAIN SWITCH Press this in (low) if you ar e connecting a line-level input source to channels 1 to 6. Press this out (high) if you ar e connecting a micro- phone-level signal to channels 1 to 8, or a instrument- level signal to channels 5 and 6 only (hi-z switch in). Note that the gain switch has no effect on the line- level i ...

  • Mackie PPM1008 - page 19

    19 Owner’ s Manual Owner’ s Manual 33. COMPRESSOR Channels 1 to 4 have an in-line compressor circuit with a variable threshold. This is very useful for com- pression of vocals, for example. When the incoming signals exceed the threshold level set by this knob, the signal level is automatically com- pressed. This r educes the dynamic range, and ...

  • Mackie PPM1008 - page 20

    20 PPM1008 PPM1008 Master Controls 35. POWER LED This LED comes on when the powered mixer is plugged into the correct-voltage AC mains supply , and the rear panel power switch [2] is on. If the LED does not turn on, make sure the AC power is live, both ends of the power cord are corr ectly in- serted, your electricity bill has been paid, and the li ...

  • Mackie PPM1008 - page 21

    21 Owner’ s Manual Owner’ s Manual The control does not affect the monitor 1 output [17], monitor 2 output [15], or the internal power amp if it is playing a monitor . (For stage monitor work, it is good that the main mix level does not affect the monitor out- puts, so they can be set up nicely and stay that way .) The main mix signals are off ...

  • Mackie PPM1008 - page 22

    22 PPM1008 PPM1008 46. PHANTOM SWITCH Press in this switch to add phantom power to all the XLR microphone inputs of the mixer . This lets the mixer send low-current DC voltage to the mic’ s electronics through the same wires that carry audio. The LED will turn on as a reminder that phantom power is engaged. Most modern professional condenser mics ...

  • Mackie PPM1008 - page 23

    23 Owner’ s Manual Owner’ s Manual The signals going into the processor are affected by the channel FX/mon 2 controls [22], and the channel level controls [31] (if the FX send/mon 2 send switch [51] is out (post)). Check the LED if you alter these controls. 51. FX SEND (POST)/MON 2 SEND (PRE) This switch lets you choose which signal path is use ...

  • Mackie PPM1008 - page 24

    24 PPM1008 PPM1008 Appendix A: Ser vice Information If you think your powered mixer has a problem, please check out the following troubleshooting tips and do your best to confi rm the problem. Visit the Support section of our website (www .mackie.com) where you will fi nd lots of useful information such as F AQs, documentation and user forums. Y ...

  • Mackie PPM1008 - page 25

    25 Owner’ s Manual Owner’ s Manual “XLR” Connectors Mackie mixers use 3-pin female “XLR” connectors on all microphone inputs, with pin 1 wired to the grounded (earthed) shield, pin 2 wired to the “high” (”hot” or positive polarity) side of the audio signal and pin 3 wired to the “low” (“cold” or negative polarity) side o ...

  • Mackie PPM1008 - page 26

    26 PPM1008 PPM1008 Loudspeaker Cable Use loudspeaker cables with a minimum conductor size for the length you need as listed in these tables. This will minimize power losses to less than 0.5 dB. The cable lengths listed are “up to” lengths. For in- between lengths, use the next larger con- ductor gauge. Using larger than the rec- ommended conduc ...

  • Mackie PPM1008 - page 27

    27 Owner’ s Manual Owner’ s Manual Appendix C: T echnical Information Specifi cations Distortion (THD + N) (1 kHz, 30 kHz bandwidth) Mic mono: <0.007% high gain <0.005% low gain Line mono: <0.005% low gain Line stereo <0.01% at main out Main mix output noise (1 kHz, 30 kHz bandwidth) Main mix level down, all channel levels down: ? ...

  • Mackie PPM1008 - page 28

    28 PPM1008 PPM1008 Dimensions 12.3 in/ 314mm 19.3 in/ 490 mm 11.4 in/ 290 mm WEIGHT 24.5 lb 11.1 kg Correct disposal of this product. This symbol indicates that this product should not be disposed of with your household waste, according to the WEEE Directive (2002/96/EC) and your national law . This product should be handed over to an authorized co ...

  • Mackie PPM1008 - page 29

    29 Owner’ s Manual Owner’ s Manual Block Diagram West Ham Plaistow Upton Park East Ham Upney Dagenham Heathway Dagenham East Elm Park Hornchurch Upminster Bridge Upminster Becontree Barking 48V Mics Mo n 2 (pre) Efx (p ost ) L R L R Main lev el Stereo Channels 7-8 L R Mono Channels Mic Line Inser t Gain Channel Lev el Channel Lev el Mon L Main ...

  • Mackie PPM1008 - page 30

    30 PPM1008 PPM1008 Appendix D: T able of Effects Presets No. Title Description Example of its use 01 Plate Reverb This preset emulates vintage mechanical reverberation that was generated with a metal plate. Its sound is char- acterized by lots of early refl ections and no pre-delay. Perfect for thickening percussive instruments, such as a snare dr ...

  • Mackie PPM1008 - page 31

    31 Owner’ s Manual Owner’ s Manual PPM1008 Limited W arranty A. LOUD T echnologies Inc. warrants all materials, workmanship and proper operation of this product for a period of three years from the original date of purchase. Y ou may purchase an additional 24-month Extended W arranty (for a total of 60 months of coverage). V isit our website an ...

  • Mackie PPM1008 - page 32

    16220 W ood-Red Road NE • Woodinville, W A 98072 • USA United States and Canada: 800.898.3211 Europe, Asia, Central and South America: 425.487 .4333 Middle East and Africa: 31.20.654.4000 F ax: 425.487 .4337 • www .mackie.com E -mail: sales@mackie.com ...

Fabricant Mackie Catégorie Music Mixer

Les documents que nous recevons du fabricant de l'appareilMackie PPM1008 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Mackie
- manuels d’utilisations PPM1008
- fiches produit Mackie
- dépliants
- ou étiquettes-énergie Mackie PPM1008
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Mackie PPM1008.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Mackie PPM1008, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Mackie PPM1008. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Mackie PPM1008.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Mackie PPM1008, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Mackie PPM1008 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Mackie PPM1008.

Le manuel d’utilisation complet Mackie, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Mackie PPM1008 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Mackie PPM1008, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lMackie PPM1008 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Mackie PPM1008 - qui devraient nous aider dans les premières étapes lors de l'utilisation Mackie PPM1008
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Mackie PPM1008
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Mackie PPM1008 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Mackie PPM1008?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Mackie PPM1008, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Mackie PPM1008 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)