-
Miele 09 730 840 - page 1
Operating and installation instructions Cooker hood To avoid the risk of accidents or damage to this appliance, it is essential to read these instructions before it is installed and used for the first time. M.-Nr. 09 730 840 e n-G B ...
-
Miele 09 730 840 - page 2
Warning and Safety instructions .....................................4 Caring for the environment .........................................1 3 Guide to the appliance ............................................1 4 Modes of operation ...............................................1 6 Con | ctivity 2.0 ................................................ ...
-
Miele 09 730 840 - page 3
Connection for air extraction .......................................3 6 Condensate trap ..................................................3 7 Silencer .........................................................3 8 Electrical connection .............................................3 9 Activating the Con | ctivity 2.0 function ........................ ...
-
Miele 09 730 840 - page 4
This appliance complies with all relevant safety requirements. Improper use of the appliance can, however, present a risk of both personal injury and damage to property. To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before installation and before using it for the first time. They contain import ...
-
Miele 09 730 840 - page 5
~ The appliance can only be used by people with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, if they are supervised whilst using it, or have been shown how to use it in a safe way and recognise and understand the consequences of incorrect operation. Safety with children ~ Children under 8 years of age must ...
-
Miele 09 730 840 - page 6
Technical safety ~ A damaged appliance can be dangerous. Check the appliance for visible signs of damage. Do not use a damaged appliance. ~ The electrical safety of this appliance can only be guaranteed if it is correctly earthed. It is essential that this standard safety requirement is met. If in any doubt please have the electrical installation t ...
-
Miele 09 730 840 - page 7
~ A damaged connection cable must only be replaced by an approved and suitably qualified technician. ~ Miele can only guarantee the safety of the appliance when original Miele replacement parts are used. Faulty components must only be replaced by genuine Miele original spare parts. ~ During installation, maintenance and repair work, the appliance m ...
-
Miele 09 730 840 - page 8
Using at the same time as other heating appliances that depend on the air from the room Danger of poisoning by toxic fumes. ~ Great care should be taken when using the cooker hood at the same time and in the same room or area of the house as another heating appliance which depends on air in the room. Such appliances include gas, oil, wood or coal-f ...
-
Miele 09 730 840 - page 9
In order to ensure safe operation, and to prevent gases given off by the heating appliances from being drawn back into the room when the cooker hood and the heater are in operation simultaneously, an underpressure of 0.04 mbar (4 pa) is the maximum permissible in the room. This can be achieved by providing adequate ventilation such as air inlets wh ...
-
Miele 09 730 840 - page 10
Correct use ~ Danger of burning with open flames. Never use an open flame beneath the cooker hood. To avoid the danger of fire, do not flambé or grill over an open flame. When switched on, the cooker hood could draw flames into the filter. Fat particles sucked into the cooker hood present a fire hazard. ~ When cooking with a gas hob, a build-up of ...
-
Miele 09 730 840 - page 11
~ Do not use the cooker hood without the filters in place. This way you will avoid the risk of grease and dirt getting into the appliance and hindering its smooth operation. ~ The filters should be regularly cleaned or changed as appropriate. Saturated filters are a fire hazard. ~ The cooker hood can get very hot during cooking due to heat rising f ...
-
Miele 09 730 840 - page 12
~ All ducting, pipework and fittings must be of non-flammable material. These can be obtained from the Miele Spare Parts department or from builders' merchants. ~ The appliance must not be connected to a chimney or vent flue which is in use. Neither should it be connected to ducting which ventilates rooms with fireplaces. ~ If exhaust air is t ...
-
Miele 09 730 840 - page 13
Disposal of the packing material The packaging is designed to protect the appliance from damage during transportation. The packaging materials used are selected from materials which are environmentally friendly for disposal, and should be recycled. Recycling packaging reduces the use of raw materials in the manufacturing process and also reduces th ...
-
Miele 09 730 840 - page 14
Guide to the appliance 14 ...
-
Miele 09 730 840 - page 15
a Extension piece b Tower c Canopy d Controls e Grease filters f Recirculation grille (only for recirculation mode) g Hob lighting h Charcoal filter (special accessory for recirculation mode) i Sensor for switching the fan on and off j Sensor for the hob lighting k Sensors for selecting the fan power level l Sensor for the run-on option This sensor ...
-
Miele 09 730 840 - page 16
The cooker hood works with . . . air extraction: The air is drawn in, cleaned by the grease filters and directed outside. If the on-site ventilation system does not have a non-return flap , then the non-return flap supplied with the appliance must be fitted in the exhaust socket of the motor unit. Having a non-return flap fitted in the ducting ensu ...
-
Miele 09 730 840 - page 17
Con | ctivity 2.0 Automatic control This cooker hood is fitted with a communication module which enables the operation of the cooker hood to be automatically controlled by the operating status of a Miele electric hob with onset controls. The hob transmits information about its operating status to the cooker hood via radio. – When the hob is switc ...
-
Miele 09 730 840 - page 18
When Con | ctivity 2.0 is activated, the cooker hood always operates in automatic mode (see "Activating the Con | ctivity 2.0 function"). To operate the cooker hood manually, see "Cooking without the Con | ctivity 2.0 function". Cooking with the Con | ctivity 2.0 function (Automatic mode) ^ Switch on the hob and select a setting ...
-
Miele 09 730 840 - page 19
Frying food ^ If the hob is switched on at the highest setting and is turned down to a lower setting after approx. 60 to 90 seconds*, a frying process is recognised. (* 60 seconds to 5 minutes with a HiLight hob). The cooker hood switches itself on and, when the hob is turned down to a lower setting, switches itself to level 3 and remains at this l ...
-
Miele 09 730 840 - page 20
Leaving automatic mode temporarily ^ You can also leave automatic mode during cooking, by – manually selecting a different fan power level, or – manually switching off the cooker hood, or – activating the run-on option " "o n the cooker hood. The fan will then switch off after the run-on time selected. The lighting will remain o ...
-
Miele 09 730 840 - page 21
Cooking without the Con | ctivity 2.0 function (Manual mode) The Con | ctivity 2.0 function must not be activated for this mode. However, manual operation is temporarily possible even if the Con | ctivity 2.0 function is activated (see "Leaving automatic mode temporarily"). To switch the fan on s ^ Touch the On/Off sensor s . The fan will ...
-
Miele 09 730 840 - page 22
Power management system The cooker hood features a Power management system to help save energy. The fan power level is reduced and the lighting is switched off automatically. – If the Intensive setting is selected, the fan will automatically revert to level 3 after 5 minutes, to level 2 after 2 hours and then after a further 30 minutes to level 1 ...
-
Miele 09 730 840 - page 23
Filter operating hours counter [ The number of hours the cooker hood has been in operation is stored in memory. The operating hours counters tell you when the grease filters or charcoal filters need to be cleaned or replaced. Grease filter operating hours counter After 30 hours of operation (or another time if the operating hours counter has be ...
-
Miele 09 730 840 - page 24
One or more of sensors 1 to IS will flash. The number of flashing sensors indicates the percentage of the operating time which has already been used up. Sensor 1 ....................2 5% Sensor 1 and 2 ...............5 0% Sensor 1 to 3 .................7 5% Sensor 1 to IS ...............1 0 0% ^ When you take your finger off the Grease filter senso ...
-
Miele 09 730 840 - page 25
Checking the charcoal filter operating hours counter To check the percentage of time set already used: ^ Touch the On/Off sensor s to switch the fan on. ^ Touch and keep your finger on the Charcoal filter sensor . One or more of sensors 1 to IS will flash. The number of flashing sensors indicates the percentage of the operating time which has a ...
-
Miele 09 730 840 - page 26
, Disconnect the cooker hood from the mains supply before mainentance and care (see "Warning amnd Safety"). Housing General The surfaces and controls are susceptible to scratches and abrasion. Please observe the following cleaning instructions. ^ All external surfaces and controls can be cleaned using a microfibre cloth or with warm water ...
-
Miele 09 730 840 - page 27
Grease filters The re-usable metal grease filters in the appliance remove solid particles (grease, dust, etc.) from the kitchen vapours, preventing soiling of the cooker hood. The grease filters should be cleaned regularly (at least every 3-4 weeks) to avoid a build-up of grease, but always clean immediately if the Grease filter sensor [ lights up. ...
-
Miele 09 730 840 - page 28
^ After cleaning, leave the filters to dry on an absorbent surface before replacing them. ^ When removing the filters for cleaning, also clean off any residues of oil or fat from the now accessible housing to prevent the risk of these catching fire. ^ Replace the grease filters, making sure that the locking clips are facing down towards the hob. ^ ...
-
Miele 09 730 840 - page 29
Fitting and replacing the charcoal filters If the cooker hood is connected for recirculation, a charcoal filter must be inserted in addition to the grease filters. This is designed to absorb cooking odours. It is fitted in the canopy above the grease filters. New charcoal filters can be purchased from your Miele dealer, from the Miele Spare Parts D ...
-
Miele 09 730 840 - page 30
The diagram is not drawn to scale. Appliance dimensions 30 ...
-
Miele 09 730 840 - page 31
a Extraction b Recirculation c Ventilation grill positioned at the top for recirculation d , e The shaded areas represent the wall or ceiling area for the vent cut-out and for fitting the connection socket. For recirculation mode, you only require cut-out area d and a connection socket. Connection for air extraction C 150 mm, or C 125 mm with reduc ...
-
Miele 09 730 840 - page 32
– When deciding on the safety distance between the hob and cooker hood, please note that a distance of 650 mm above electric cookers/hobs may be preferable to give more working space under the hood. – Account should also be taken of the height of the person who will be using the hood most often. The person should have sufficient space to work c ...
-
Miele 09 730 840 - page 33
Before installation, it is important to read the information given on the following pages as well as the "Appliance dimensions" and the "Warning and safety instructions" at the beginning of this booklet. This is particularly crucial when using the cooker hood at the same time as a heating appliance that relies on oxygen from the ...
-
Miele 09 730 840 - page 34
Installation accessories Installation 34 ...
-
Miele 09 730 840 - page 35
a 3 protective sheets for use when fitting the tower. b 1 exhaust socket for exhaust ducting C 150 mm. c 1 reducing collar for exhaust ducting C 125 mm. d 1 non-return valve for fitting into the exhaust connection on the motor unit (not for recirculation mode) e Telescopic wall bracket for securing the cooker hood to the wall. f Con@ctivity 2.0 sti ...
-
Miele 09 730 840 - page 36
Important: To avoid the danger of toxic fumes, please observe the Warning and Safety instructions. This is especially crucial when using the cooker hood at the same time as another heating appliance which relies on air from the same room. The cooker hood should be installed according to local and national building regulations. Seek approval from th ...
-
Miele 09 730 840 - page 37
– If the exhaust air is to be ducted into the open air, the installation of a telescopic wall vent or roof vent (available as an optional accessory) is recommended. – If the exhaust air is to be ducted into a vent flue, the ducting must be directed in the flow direction of the flue. Important: If the exhaust ducting is to run through rooms, cei ...
-
Miele 09 730 840 - page 38
Silencer (optional accessory) To achieve even further reductions in noise levels, a special silencer can be fitted in the ducting system. ...with air extraction: The silencer not only reduces noise from the motor outside the house, but also sounds from outside (e.g. traffic noise). For this reason the silencer must be positioned as close as possibl ...
-
Miele 09 730 840 - page 39
All electrical work should be undertaken by a suitably qualified and competent person in strict accordance with current national and local safety regulations (BS 7671 in the UK). Installation, repairs and other work by unqualified persons could be dangerous, for which the manufacturer cannot be held liable. Ensure power is not supplied to the appli ...
-
Miele 09 730 840 - page 40
Installing the Con | ctivity 2.0 stick The hob must be fitted with the Con | ctivity 2.0 stick so that the Con | ctivity 2.0 function can be used. This is supplied with this cooker hood. ^ Please refer to the installation instructions for the Con | ctivity 2.0 stick. The radio connection between the hob and the cooker hood must be activated so that ...
-
Miele 09 730 840 - page 41
^ Touch the IS sensor to activate Con | ctivity 2.0. While it is searching for the radio connection, the 2 sensor will light up and 3 will flash. ^ Meanwhile you can start the activation process for the hob. Activating the Con | ctivity 2.0 function on the hob ^ While the cooker hood is searching for the radio connection, start the activation proce ...
-
Miele 09 730 840 - page 42
Deactivating To deactivate the cooker hood: ^ Switch off the fan, hob lighting and hob. ^ Touch the Run-on sensor ¢ for approx. 10 seconds until the 1 sensor lights up. ^ Touch in turn – the 1 sensor, – then the IS sensor, – then the lighting sensor I . If the Con | ctivity 2.0 function is activated, 2 and 3 will light up constantly. ^ Touch ...
-
Miele 09 730 840 - page 43
In the event of a fault which you cannot correct yourself, or if the appliance is under guarantee, please contact: – Your Miele Dealer / Chartered Agent or – The Miele Service Department (see back cover for address). When contacting your Dealer or Miele, please quote the model and serial number of your appliance. These are shown on the data pla ...
-
Miele 09 730 840 - page 44
Total connected load * .........9 9W - Fan motor* .................9 0W - Hob lighting ..............3x3W Voltage ................. A C2 3 0V Frequency .................. 5 0H z Fuse rating ...................1 0A Electrical cable length ......................1 . 5m Weight ......................2 6k g Fan performance* Extraction power according to ...
-
Miele 09 730 840 - page 45
45 ...
-
Miele 09 730 840 - page 46
46 ...
-
Miele 09 730 840 - page 47
47 ...
-
Miele 09 730 840 - page 48
M.-Nr. 09 730 840 / 01 e n-G B DA 6690 W DA 6690 W EXT ...
Avez-vous une question à propos de Miele 09 730 840?
Utiliser le formulaire ci-dessous
Si vous n’avez pas résolu votre problème avec Miele 09 730 840, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Miele 09 730 840 il est probable qu’il a envie de partager la façon de le résoudre.