-
Electrolux 2020 D - page 1
2020 D Cooker Hood Operating and Installation Instructions ...
-
Electrolux 2020 D - page 2
2 For the User Important Safety Information Y our Appliance Operating Instructions Cooker Hood Controls T o Operate Recirculation Extraction Maintenance and Cleaning External Cleaning Metal Grease Filter T o Remove the Grease Filter Cassette Charcoal Filter T o Remove/Replace the Charcoal Filter Worktop Lighting Replacing the Light Bulb Something N ...
-
Electrolux 2020 D - page 3
3 Installation • Any installation work must be undertaken by a qualified electrician or competent person. • This hood must be installed in accordance with the installation instructions and all measurements adhered to. • If the cooker hood is installed for use above a gas appliance then the provision for ventilation must be in accordance with ...
-
Electrolux 2020 D - page 4
4 YOUR APPLIANCE OPERA TING INSTRUCTIONS This cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam . T o obtain the best performance it is advisable to switch on the hood a few minutes before you start cooking and leave it running for approximately 15 minutes after finishing. Cooker Hood Controls V1. Push ...
-
Electrolux 2020 D - page 5
5 This cooker hood can be used to recirculate or extract contaminated air. Recirculation The cooker hood is supplied specified for use in the recirculation mode with the charcoal filter fitted. The contaminated air is cleaned by passing through the filters and than back into the kitchen. The activated charcoal filter absorbs odours arising from coo ...
-
Electrolux 2020 D - page 6
6 MAINTENANCE AND CLEANING Before carrying out any maintenance or cleaning isolate the cooker hood from the mains supply . The cooker hood must be kept clean, a build up of grease or fat can be a fire hazard. External Cleaning The metal casing, grille and chimney should be cleaned at least once a month to keep it looking like new. Wipe over the hoo ...
-
Electrolux 2020 D - page 7
7 T o Remove the Charcoal Filter Push inwardly on the two retaining clips to disengage the security fixing and remove. This appliance can be a fire hazard if the grease and charcoal filters are not cleaned and replaced as recommended. Worktop Lighting The lamps should be replaced with a 220-240V 20W halogen spot lamp. T o Remove the Lamps Unscrew t ...
-
Electrolux 2020 D - page 8
8 SOMETHING NOT WORKING SERVICE AND SP ARE P ARTS If, having followed these instructions carefully , your cooker hood fails to work properly please carry out the following checks. Symptom The cooker hood will not start The cooker hood is not working effectively The cooker hood has switched off during operation If after all these checks, the problem ...
-
Electrolux 2020 D - page 9
9 GUARANTEE CONDITIONS Standard Guarantee Conditions We, AEG, undertake that if within 12 months of the date of the purchase this AEG built-in appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, the company will, at our option, repair or replace the same FREE OF ANY CHARGE for labour , material ...
-
Electrolux 2020 D - page 10
10 INST ALLA TION INSTRUCTIONS It is dangerous to alter the specifications or attempt to modify this product in any way . T echnical Information DIMENSIONS HEIGHT (CANOPY): 73 mm HEIGHT (CHIMNEY): 450-850 mm WIDTH (CANOPY): 898 mm WIDTH (CHIMNEY): Ø200-Ø270 mm GROSS: 24.00 kg NET : 19,40 kg ELECTRICAL SUPPL Y : 220-240 V (50 Hz) POWER CONSUMPTION ...
-
Electrolux 2020 D - page 11
11 INST ALLING THE COOKER HOOD Please ensure that when the appliance is installed it is easily accessible to an engineer in the event of a breakdown. All installations must comply with the local authorities requirements for the discharge of exhaust air . Incorrect installation may affect the safety of this cooker hood. Installation Requirements Bef ...
-
Electrolux 2020 D - page 12
12 A: Built-in Electric Hob: 650mm minimum clearance B: Built-in Gas hob: 700mm minimum clearance C: Slot-in Electric Cooker: 685mm minimum clearance D: Slot-in Gas Cooker: 787mm minimum clearance Hob Clearance Heights The cooker hood is designed to be fitted over a cooking appliance at the clearance heights stated, provided the maximum output of t ...
-
Electrolux 2020 D - page 13
13 Fixing the Chimney to the Canopy 1 . Remove the metal grease filter cassette by pushing inwardly on the two steel handles. 2. T o remove the charcoal filter push inwardly on the two retaining clips to disengage the security fixing and remove. 3. Align the fixing points on the chimney with the corresponding fixing points on the canopy . Ensure th ...
-
Electrolux 2020 D - page 14
14 3. Slide the chimney through the hole in the shelf before fixing it to the canopy . T op Shelf The top shelf only requires drilling if the hood is to be installed with the air outlet turned upwards. 1. Use the cardboard template provided to mark the hole position on the shelf. 2. Using the hole ‘B’ as a reference point, drill the shelf along ...
-
Electrolux 2020 D - page 15
15 5. Fix the round eyelet screws provided tightly into the holes (1). 6. Fix bracket (S) to the fan assembly . 7. The hood is supplied in the recirculation mode, with the recirculation grille (G) fitted over the outlet in the top of the fan assembly ready for use. 8. Insert the 4.2x44.4mm screws to be used for fixing the fan assembly into the rawl ...
-
Electrolux 2020 D - page 16
16 5. Mark the position on the wall and drill the hole for the ducting. T o calculate the centre of the hole on the wall for the ducting, draw a horizontal line (D) through the vertical line 80mm above line (X) The round ducting to be used must be Ø125mm. 6. Fix the round eyelet screws provided tightly into holes (1) and hook on the canopy (C) ens ...
-
Electrolux 2020 D - page 17
17 4. Using a 8mm masonry bit, drill the holes for the canopy and fan assembly and insert the rawl plugs ready for the fixing screws. 5. The hood is supplied with the air outlet facing the rear . T o rotate the extractor to face left or right proceed as follows: (A) Loosen the screws (V1), turn the extractor 60 ° t o the left or right as required, ...
-
Electrolux 2020 D - page 18
18 Final fixing and adjustment of the hood: T wo adjustable connectors are provided at the rear of the hood. (a) T urn the screws (V1), until the screws (V2) align with the screw holes (F2). (b) Adjust the vertical and horizontal alignment using screws (V2). (c) T urn the screw (V1) to secure the hood to the wall. (d) Insert the plastic grommets pr ...
-
Electrolux 2020 D - page 19
19 Electrical connection and working test: 1. Remove the metal cover by unscrewing the four self tapping screws. 2. Connect the ‘Push-Fit’ connectors coming from the fan assembly to the canopy . 3. Position the terminals as illustrated under the cover and replace the cover with the four self tapping screws. 4 . Once the electrical connection ha ...
-
Electrolux 2020 D - page 20
4329477 01 - 001013 ...
Avez-vous une question à propos de Electrolux 2020 D?
Utiliser le formulaire ci-dessous
Si vous n’avez pas résolu votre problème avec Electrolux 2020 D, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Electrolux 2020 D il est probable qu’il a envie de partager la façon de le résoudre.