Manuel d’utilisation Memorex MT1132

28 pages 0.73 mb
Télécharger

Aller à la page of 28

Summary
  • Memorex MT1132 - page 1

    VOLUME CHANNEL POWER R MT1132 13'' Color Television Owner's Manual VIDEO INPUT R VIDEO AUDIO As an E NERGY S TAR ® Partner, MEMCORP has determined that this product meets the E NERGY S TAR ® guideli nes for energy efficiency. ...

  • Memorex MT1132 - page 2

    – 1 – To get the most from your new color television, read and follow this Owner's Manual carefully. INSTALLATION GUIDELINES  Place your TV in a room with adequate ventilation.  Keep your TV set away from sources of direct heat, such as heat registers or direct  sunlight.  Do not place your TV on soft surfaces, such as rugs ...

  • Memorex MT1132 - page 3

    – 2 – FEATURES SPECIFICATIONS  On-screen graphics guide you through setup features and operations  Automatic programming of channels allows easy selection of stations available in your  viewing area   Sleep timer programs the TV to turn itself off at a preset time  One day timer programs the TV to come on once at a preset time ...

  • Memorex MT1132 - page 4

    – 3 – LOCATION OF CONTROLS 1  POWER SWITCH 2  CHANNEL (UP) BUTTON 3  CHANNEL (DOWN) BUTTON 4 VOLUME (UP) BUTTON 5 VOLUME (DOWN) BUTTON 6 REMOTE CONTROL SENSOR 7 AUDIO IN (PUT) JACK 8  VIDEO IN (PUT) JACK 9  VHF / UHF EXT. ANT. JACK (REAR OF SET) EXT.ANT. UHF/VHF 8 7 6 5 4 3 2 1 9 3180-P3 VOLUME CHANNEL ...

  • Memorex MT1132 - page 5

    – 4 – REMOTE CONTROL The REMOTE CONTROL unit requires two 1.5 volt "AA" size batteries. The BATTERY COMPARTMENT is located on the back of the unit. To open, press down of the lid and slide toward the bottom of the unit. Install the batteries exactly as shown by the diagram in the compartment. NOTE: If one or both of the batteries are ...

  • Memorex MT1132 - page 6

    POWER SLEEP TV/VIDEO 3 2 1 6 5 4 9 8 7 RECALL 0 100 + – MENU Q.REV CH1/2 TV/CAP/TEXT MUTE CHANNEL VOLUME POWER Button Press to turn the TV on or off. TV/VIDEO Button Pressing this button permits the TV to be used as a monitor to view program sources such as a VCR, Video Disc, ect. press again to resume normal TV function. SLEEP Button Press to st ...

  • Memorex MT1132 - page 7

    – 6 – ANTENNA CONNECTIONS If you are using an indoor or outdoor antenna (antennas no t included) follow the instructions below that correspond to your antenna system. I If you are using a cable television service (CATV), refer to CATV connections. Combination VHF/UHF Antenna (Single 75 ohm cable or 300 ohm twin-lead wire) Connect the 75 ohm cab ...

  • Memorex MT1132 - page 8

    Some cable companies offer "premium pay" channels in which the signal is scrambled. Descrambling these signals for normal viewing requires the use of a descrambler device which is generally provided by the cable company. The illustrations below show how to connect these types of converter/descrambler devices with the TV's VHF antenna ...

  • Memorex MT1132 - page 9

    input ...

  • Memorex MT1132 - page 10

    – 9 – SELECTING A LANGUAGE The menu screen that appears when you press the MENU button can be programmed to appear in English, French, or Spanish. Follow the directions below to program the menu screen to appear in a language other than the one that is now on-screen when you press the MENU button. Press the MENU button to bring up the menu-scre ...

  • Memorex MT1132 - page 11

    – 10 – SETTING THE CLOCK Press the MENU button twice to bring up the menu screen and select CLOCK SET. Use the + or – button to select the correct day of the week. Press the MENU button to go to the next step. Use the + or – button to select the correct hours(s). Press the MENU button to go to the next step Use the + or – button to select ...

  • Memorex MT1132 - page 12

    – 11 – PROGRAMMING CHANNELS With automatic programming, the TV automatically places every channel you receive in its memory, allowing you to scan through those channels when you press the CHANNEL (Up/Down) buttons. With manual programming, you tell the TV what channels you want to scan through when you press the CHANNEL (Up/Down) butt o ns. Aut ...

  • Memorex MT1132 - page 13

    – 12 – ADDING/DELETING CHANNELS Manual Programming Press the MENU button to bring up the menu screen. Use the + or – button to highlight CH PROGRAM, then press the MENU button to select it. Use the + or – button to highlight CH MEMORY. Press the MENU button to select CH MEMORY. 1 2 3 4 Press the CHANNEL (Up or Down) button or Number butt ...

  • Memorex MT1132 - page 14

    – 13 – SETTING THE TIMERS You can program your TV to turn on a specific channel at a preset time once (one day timer) or at the same time every day or every week (weekly timer). You also can program your TV to turn itself off after a specified amount of time (Sleep timer). One Day Timer Press the MENU button to bring up the menu-screen. Use the ...

  • Memorex MT1132 - page 15

    – 14 – 1 2 3 4 5 Use the + or – button to select the hour you want the timer to come on, then press the MENU button. Use the + or – button to select the minute(s) you want the timer to come on, then press the MENU button. Use the + or – button to select AM or PM, then press the MENU button. Follow the same steps to set the time off. Use t ...

  • Memorex MT1132 - page 16

    – 15 – 1 Press the SLEEP button until the desired sleep time (10, 20, 30, 40, 50, 60, 70, 80 or 90 minutes) appears on- screen. The timer will begin counting down to zero, and the on-screen display will disappear. When the timer reaches zero, the TV will turn itself off. 2 To check the time remaining for a sleep timer, press the SLEEP button. T ...

  • Memorex MT1132 - page 17

    – 16 – ADJUSTING THE PICTURE Press the MENU button to bring up the menu screen. Use the + or – button to highlight PICTURE ADJUST, then press the MENU button. Press the MENU button while ADJUST is highlighted. Press the MENU button until the adjustment you want to make (CONTRAST, BRIGHTNESS, COLOR, TINT or SHARPNESS – see chart at right for ...

  • Memorex MT1132 - page 18

    – 17 – CLOSED CAPTION MODE Close caption mode allows you to read the words of a broadcast on-screen while you are hearing them. There are two types of closed captioning: Captions – Dialogue and descriptions of the action appear in a box at the bottom of the screen. Text – Words appear on the screen. This is often used for channel guides. Of ...

  • Memorex MT1132 - page 19

    – 18 – CABLE TV OPERATION Press the MENU button to bring up the main menu screen. Use the + or – button to highlight CH PROGRAM, then press the MENU button to select it. Press the MENU button until CABLE appears to the right of AIR/CABLE. On CATV (Cable Television) systems, programs are brought into the home on VHF channels 2–13, mid-band c ...

  • Memorex MT1132 - page 20

    – 19 – Press the MENU button to bring up the menu-screen. Press the MENU button. The OFF (or ON) to the right of V-BLOCK will flash. SETTING V-BLOCK V-Block allow users to program their TV set to automatically block an incoming program that contains a particular level of violence, sexual content and strong language . User can easily block progr ...

  • Memorex MT1132 - page 21

    – 20 – Go to menu display item no. 6 of SETTING V-BLOCK. Press the + or - button until any rating appears beside MPAA RATING. V-BLOCK SET V-BLOCK ON CHANGE RATING CHANGE NUMBER 0000 EXIT [+] / [-] : SELECT [MENU] : ENTER V-BLOCK SET MPAA RATING PG-13 TV RATING TV-PG-DLSV OPTION RATINGOFF LOADING OFF EXIT [+] / [-] : SELECT [MENU] ...

  • Memorex MT1132 - page 22

    – 21 – Go to menu display item no. 2 of SETTING MPAA RATING. Press the + or - button until any rating appears beside TV RATING. 1 Use the + or - button to highlight TV RATING 2 V-BLOCK SET MPAA RATING PG-13 TV RATING TV-PG-DLSV OPTION RATING OFF LOADING OFF EXIT [+] / [-] : SELECT [MENU] : ENTER Press the MENU button. 3 4 Press t ...

  • Memorex MT1132 - page 23

    – 22 – Table 1 indicates the only valid combinations of age and content based ratings with an "X" in the appropriate boxes. For example, TV-14-S,V is a valid rating, as is TV- 14. However, TV-14-FV is not a valid rating. Age-based Rating TV-Y FV D L S V TV-Y7 X TV-G TV-PG X X X X X X X X X X X TV-14 TV-MA TABLE 1 Content-based Rating: ...

  • Memorex MT1132 - page 24

    – 23 – For example : If user chooses to block any program with TV-PG-V rating, all entries in that column are automatically blocked as shown in table 2. At the same time it will cause no blocking of any program with D, L, S rating. Similarly, the same will happen if user Age-based Rating TV-Y FV D L S V TV-Y7 U TV-G TV-PG U U U U U U U U B B B ...

  • Memorex MT1132 - page 25

    – 24 – Go to menu display item no. 4 of SETTING V-BLOCK. V-BLOCK SET V-BLOCK OFF CHANGE RATING CHANGE NUMBER 0000 EXIT [+] / [-] : SELECT [MENU] : ENTER 1 V-BLOCK SET V-BLOCK OFF CHANGE RATING CHANGE NUMBER 0000 EXIT [+] / [-] : SELECT [MENU] : ENTER Use the + or - button to highlight CHANGE NUMBER. 2 V-BLOCK SET V-BLOCK OFF CHANGE RATING CHANG ...

  • Memorex MT1132 - page 26

    – 25 – SETTING OPTION RATING (CHANGE RATING-3) This setting is use to receive data service for Canadian English Language Rating System in accordance with EIA-744-A Standard. Go to menu display item no. 2 of SETTING MPAA RATING. 1 Use the + or - button to highlight OPTION RATING. 2 Use the + or - button to highlight the rating you want to select ...

  • Memorex MT1132 - page 27

    – 26 – SETTING LOADING Go to menu display item no. 8 of SETTING OPTION RATING. 1 Press the + or - button until ON appears beside LOADING then press the MENU button. 3 Press the MENU button to exit. 4 V-BLOCK SET MPAA RATING PG-13 TV RATING TV-PG-DLSV OPTION RATING ON LOADING OFF EXIT [+] / [-] : SELECT [MENU] : ENTER Press the ME ...

  • Memorex MT1132 - page 28

    PROBLEM SOLUTION Make sure batteries are inserted in the remote control. Make sure the remote control is aimed directly at the remote sensor on the TV. Press the TV/CAP/TEXT button until the CAP or TEXT box disappears from the screen. Adjust the brightness and contrast controls. Check the antenna for shorted or broken wires. Reposition the antenna. ...

Fabricant Memorex Catégorie CRT Television

Les documents que nous recevons du fabricant de l'appareilMemorex MT1132 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Memorex
- manuels d’utilisations MT1132
- fiches produit Memorex
- dépliants
- ou étiquettes-énergie Memorex MT1132
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Memorex MT1132.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Memorex MT1132, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Memorex MT1132. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Memorex MT1132.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Memorex MT1132, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Memorex MT1132 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Memorex MT1132.

Le manuel d’utilisation complet Memorex, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Memorex MT1132 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Memorex MT1132, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lMemorex MT1132 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Memorex MT1132 - qui devraient nous aider dans les premières étapes lors de l'utilisation Memorex MT1132
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Memorex MT1132
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Memorex MT1132 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Memorex MT1132?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Memorex MT1132, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Memorex MT1132 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (0)