-
Grizzly H6146 - page 1
COPYRIGHT © FEBRUARY, 2005 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #BL6906 PRINTED IN CHINA 3 4 ° C L I P P E D H E A D F R A M I N G N A I L E R MODEL H6146 INSTRUCTION MANUAL ...
-
Grizzly H6146 - page 2
For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazard- ous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. R ...
-
Grizzly H6146 - page 3
H6146 34° Clipped Head Framing Nailer -1 - 6. ONLY ALLOW TRAINED AND PROPERLY SUPERVISED PER- SONNEL TO OPERATE MACHIN- ERY. Make sure operation instruc- tions are safe and clearly under- stood. 7. KEEP CHILDREN AND VISITORS AWAY. Keep all children and visi- tors a safe distance from the work area. 8 . MAKE WORKSHOP CHILD PROOF. Use padlocks, mast ...
-
Grizzly H6146 - page 4
H6146 34° Clipped Head Framing Nailer -2 - 1. HAND INJURIES: Do not place your hands near the nail point of entry. A nail can deflect and tear through the surface of the workpiece, puncturing your hand or fingers. 2. COMBUSTIBLE GASES: Never connect the nailer to pressurized oxygen or other combustible gases as a power source . Only use fil- tered ...
-
Grizzly H6146 - page 5
H6146 34° Clipped Head Framing Nailer -3 - Operating this nailer can propel objects into the air, causing imme- diate eye damage. To protect your- self, always wear American National Standards Institute (ANSI) approved safety glasses or goggles when oper- ating this equipment. In addition, this nailer discharges at 85-90 decibels. To protect your ...
-
Grizzly H6146 - page 6
H6146 34° Clipped Head Framing Nailer -4 - INTRODUCTION If you have any c omme nts reg ard ing th is man ual, pl ease w rite to u s at the follow ing add ress : Grizzly Industrial, Inc. C/O Technical Documentation P.O. Box 2069 Bellingham, WA 98227-2069 Mo st i mpor t antl y , we s tand b ehin d ou r too ls. If you have any ser vi ce que stio ns o ...
-
Grizzly H6146 - page 7
H6146 34° Clipped Head Framing Nailer -5 - SET UP Figure 1. Model H6146 inventory. Unpacki ng Y our Mo del H 61 4 6 lef t our ware hou se in a c arefu lly pac ked b ox. If you d isc over th e n ail er is d amag ed af te r yo u have sig ned for del iver y , ple ase i mme diat ely cal l Cu stom er Ser vice at ( 57 0 ) 54 6- 96 63 for advic e. Save t ...
-
Grizzly H6146 - page 8
H6146 34° Clipped Head Framing Nailer -6 - Compressed Air Sy stem The M ode l H 61 4 6 is desi gne d to b e o per- ated at 70-1 20 PS I us ing cle an, dr y , r egu - late d, c omp ress ed a ir . DO NOT exce ed th e max imum op er ati ng pre ssu re for your mod el . Befo re u sing your new na iler, reg ulate the air pr essu re on you r air co mpre ...
-
Grizzly H6146 - page 9
H6146 34° Clipped Head Framing Nailer -7 - Safety Y ok e A safet y yoke me chan ism (b ump fi re) o n the nos e of the nai ler ac ts as a se con d- ar y safet y d evic e. W hen th e t rig ger i s pres sed , the nailer wil l not f ire un til t he safet y yoke m ech anis m i s de pres sed. Befo re you us e your nai ler for t he fir st tim e, che ck ...
-
Grizzly H6146 - page 10
H6146 34° Clipped Head Framing Nailer -8 - OPERATIONS Loadin g Figure 3. Sliding pusher toward the catch lever. When replacing nails in your Model H6146, follow these guidelines: Diameter: 7 ⁄ 64 "- 1 ⁄ 8 " Length: 2"-3 1 ⁄ 2 " Capacity: 100 Strip Angle: 34° To load your nailer: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! ...
-
Grizzly H6146 - page 11
H6146 34° Clipped Head Framing Nailer -9 - Figure 6. Loosening cap screw for depth adjustment. The nose of the gun houses a depth adjust- ment mechanism for setting the nail depth. To adjust the dep th: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! 2. If the nail is driven too far into the workpiece, loosen the cap screw on the safety nose with a 4mm ...
-
Grizzly H6146 - page 12
H6146 34° Clipped Head Framing Nailer -10 - A jammed nail must be cleared before using the nailer again. The two places where a nail ca n get jammed are the maga- zine and the discharge area. To clear a jammed nail from the maga- zine: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! 2 . Pull back and lo ck th e maga zine push- er. 3. Remove the nail sti ...
-
Grizzly H6146 - page 13
H6146 34° Clipped Head Framing Nailer -11 - Replacin g Pist ons / O - Rin gs If yo u us e your na iler day i n an d day out , repa ir pisto ns are chea p ins uran ce agai nst wa sted do wn tim e and los t profi ts, in the event that a p isto n or pi ston sha ft bec ome s wo rn o ut. 5. The top of the piston should now be visible inside the cylinde ...
-
Grizzly H6146 - page 14
H6146 34° Clipped Head Framing Nailer -12 - CLEANING & LUBRICATION Cleanin g Use a go od s olven t to cl ean t he no se ass emb ly of the nail er . Always be s ure th at t he n ail er i s dr y bef ore us ing it agai n. Do not a llow du st, c hips , s and, etc . i nto the air co nnec tor s or i nto t he bo dy o f th e nai ler; th is may res ult ...
-
Grizzly H6146 - page 15
H6146 34° Clipped Head Framing Nailer -13 - H6146 PARTS BREAKDOWN ? ...
-
Grizzly H6146 - page 16
H6146 34° Clipped Head Framing Nailer -14 - H6146 PARTS LIST PART # DESCRIPTION REF PART # DESCRIPTION 1 PH6146001 SPCL CAP SCR M8-1.25 X 30 47 PSB03M CAP SCREW M5-.8 X 8 2 PH6146002 AIR DEFLECTOR 48 PW02M FLAT WASHER 5MM 3 PH6146003 RUBBER WASHER 49 PH6146049 ADJUSTING NUT 4 PH6146004 SPRING 50 PH6146050 SAFETY YOKE 5 PH6146005 SPRING WIRE 51 PH6 ...
-
Grizzly H6146 - page 17
H6146 34° Clipped Head Framing Nailer -15 - TROUBLESHOOTING 1. O-rings must be replaced & operation of safety yoke must be checked. 1. Tighten screws. 2. Replace O-ring. 3. Tighten air fitting & use teflon tape. 1. Replace damaged seals. 1. Tighten screws and fit - tings. 2. Clean nose. 3. Clean magazine and inspect/repair damage. 4. Check ...
-
Grizzly H6146 - page 18
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty and any and all warr ...
-
Grizzly H6146 - page 19
Name _________________________________________________________________________ Street ________________________________________________________________________ City____________________State________Zip_________ Phone Number____________E-Mail___________________FAX ____________ Model # H6146 34° Clipped Head Framing Nailer Serial#______________Order # ...
-
Grizzly H6146 - page 20
FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name________________________________ Street________________________________ City______________State______Zip_______ Send a Grizzly Catalog to a friend: Place Stamp Here ...
Avez-vous une question à propos de Grizzly H6146?
Utiliser le formulaire ci-dessous
Si vous n’avez pas résolu votre problème avec Grizzly H6146, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Grizzly H6146 il est probable qu’il a envie de partager la façon de le résoudre.