Français dropdown-ico

Manuel d’utilisation Trango Systems M900S

53 pages 2.04 mb
Télécharger

Aller à la page of 53

Summary
  • Trango Systems M900S - page 1

    M900S™ 900 MHz Wireless Broadband System USER MANUAL March 24, 2005 Revision C for Firmware V ersion 1.3 ...

  • Trango Systems M900S - page 2

    Table of Contents Trango Trango Broadband Wire less — M900S User Manual Rev. C page ii Table of Contents Pref ace ........................................................................................................................................................................... iv FCC Information ........................................... ...

  • Trango Systems M900S - page 3

    Table of Figures Trango Trango Broadband Wireless — M900S User Manual Rev. C page iii Table of Figures Figure 1: Typi cal Depl oyment ....................................................................................................................................... 1 Figure 2: Basic Component s of an M 900S Radio ............................. ...

  • Trango Systems M900S - page 4

    Preface Trango Broadband Wireless — M900S User Manual Rev. C page iv Preface This manual c overs basic c onfigurat ion and instal lation of the M900S Wi reless Broa dband System and applie s to the followin g radio pa rt numbers: M900S-AP 900 MHz Access Point M900S-SU 90 0 MHz Subs criber Unit wit h integrate d antenna a nd connect or for exter n ...

  • Trango Systems M900S - page 5

    Introduction Trango Broadband Wire less — User Manual M900S Rev. C Page 1 Section 1 Introduction Your Trango Broadband M 900S radio sy stem provi des a reliable and robust m eans to deliver broadband access t o a wide geographic region through wireless Ethernet connectivity. Th is section will familiarize you with basic operational co ncepts, as ...

  • Trango Systems M900S - page 6

    Introduction Trango Broadband Wire less — User Manual M900S Rev. C Page 2 Both APs and SUs feature a handy "site survey" tool to check for inte rference, as well as RSSI tools for optimizing antenna positioning. The M900S also feat ures variable rec eiver threshol d, full power control, dual polarized antennas, and various link diagnost ...

  • Trango Systems M900S - page 7

    Hardware Overview Trango Broadband Wire less — User Manual M900S Rev. C Page 3 Section 2 Hardware Overv iew This section provides details about each radio in the M9 00S family. The M900S-SU and M900S-AP include bu ilt- in, electronically switchable, dual-po larized antennas, as well as a reve rse polarity SMA connector for the attachment of an e ...

  • Trango Systems M900S - page 8

    Getting Started Trango Broadband Wire less — User Manual M900S Rev. C Page 4 Figure 4: Back of Radio The radio’s m odel num ber, FCC ID, MAC ID, a nd Serial n umber, are loc ated on the backside o f the radio. 6.300 .600 Figure 5: Side of Radio & Location of Reverse Polarity SMA Connector Section 3 Getting Started This section explains how ...

  • Trango Systems M900S - page 9

    Getting Started Trango Broadband Wire less — User Manual M900S Rev. C Page 5 • Connect a Cat-5 (straight through) Ethernet cable (we recommend shield ed twisted pair) between the ODU (out door unit) port of the J-box an d the RJ-45 conn ector on the radio. Note that this cable will carry power-ove r-Ethernet (P oE). • If connecting to a COMPU ...

  • Trango Systems M900S - page 10

    Getting Started Trango Broadband Wire less — User Manual M900S Rev. C Page 6 APs and SUs c an be in o ne of two Opm odes (“ON” or “OFF”). When in Opm ode “OFF,” t he AP is not transmitting and it is not attempting to associate with SUs. Alternatively, when in Opmode “ON,” the radio is transmitting and is attempting to asso ciate. ...

  • Trango Systems M900S - page 11

    Getting Started Trango Broadband Wire less — User Manual M900S Rev. C Page 7 Browser Interface Login Page Type the password (d efault trango ) and continue. This will bring up the radio’s System Information page. Web Browser System Information Page  Note: System Information page for the SU is similar and is covered in detail later in this te ...

  • Trango Systems M900S - page 12

    Getting Started Trango Broadband Wire less — User Manual M900S Rev. C Page 8 Primary Features and Pages of the Browser Interface: Navigation Column: Each page features a navigation c olumn that runs along the left-hand side of the page. The model num ber of the radi o is li sted at the top of the navi gation colum n. On the bot tom of the navigat ...

  • Trango Systems M900S - page 13

    Getting Started Trango Broadband Wire less — User Manual M900S Rev. C Page 9 Example (to view a list of all commands which start with su ) #> ? su su [all | <suid, 1..126>] su info <suid, 1..126> su linktest <suid, 1..126> su password <suid|all> <rw|ro> <new password> <new password> su ping <suid, 1 ...

  • Trango Systems M900S - page 14

    Basic Configuration via Browser Interface Trango Broadband Wire less — User Manual M900S Rev. C Page 10 Section 4 Basic Configur ation v ia Browser Interface This section describes a few more basic concepts, as well as how to establish a wireless link using the Browser (HTTP) Interface. This section is wr itten to address only the most basic step ...

  • Trango Systems M900S - page 15

    Basic Configuration via Browser Interface Trango Broadband Wire less — User Manual M900S Rev. C Page 11 CIR DOWN: Committ ed Informati on Rate fr om AP to SU . Minim um downstream data rate (m easured in Kbps) at which the AP will attempt to deliver bandwidth to this SU. Maximum setting is 3000. MIR UP: Maximum Informati on Rate from SU to AP. Ma ...

  • Trango Systems M900S - page 16

    Basic Configuration via Browser Interface Trango Broadband Wire less — User Manual M900S Rev. C Page 12 6. CIR dn: ( AP to SU Commit ted Inform ation Rat e) – minim um downstrea m bandwi dth for t he SU in K bps. 7. MIR up: (SU to AP M axim um Inform ation Rat e) – maxi mum upstream bandwidt h for t he SU in Kb ps. 8. MIR dn: (AP to SU M axim ...

  • Trango Systems M900S - page 17

    Basic Configuration via Browser Interface Trango Broadband Wire less — User Manual M900S Rev. C Page 13 2. Set Base ID, or choose the default Base ID of 000 0. (Must match the SU. ) 3. Set AP ID (00-FF HEX), or choose t he defau lt, which is last two bytes of MAC Address. 4. Set IP, S ubnet, and Gat eway, or leave at defaul t settings. Keep in m ...

  • Trango Systems M900S - page 18

    Basic Configuration via Browser Interface Trango Broadband Wire less — User Manual M900S Rev. C Page 14 Configure Basic SU Parameters In order to establish a working link , the Base ID in the SU must match the Base ID set in the AP. SU Basic Setup: 1. Connect to the SU (see Getting Started) and open the Configuration page. 2. Set Base ID. (Must m ...

  • Trango Systems M900S - page 19

    Basic Configuration via Browser Interface Trango Broadband Wire less — User Manual M900S Rev. C Page 15 LED Summary At this point it is useful to learn abou t the LEDs that can be found on the bottom of the radio. T hese LEDs can assist the user in determining radio and l ink status. A SSOCIATION LED ( GREEN) Blinking onc e every second in Opm od ...

  • Trango Systems M900S - page 20

    Basic Configuration via Browser Interface Trango Broadband Wire less — User Manual M900S Rev. C Page 16 Link Control Page The radio’s firmware includes several useful tools to assist in determining which SUs are associated and the quality of each link. One me thod fo r verifying link quality is by using the Li nk Control page. On this page t he ...

  • Trango Systems M900S - page 21

    Basic Configuration via Browser Interface Trango Broadband Wire less — User Manual M900S Rev. C Page 17 SU Ranging Test This test reports the SU’s distance from the AP i n miles, received signal strength for uplink an d downlink, and S U Tx Power. Use a link budget calculator to a n alyze results. Advanced Setup Page The Advanced Set u p page i ...

  • Trango Systems M900S - page 22

    Basic Configuration via Browser Interface Trango Broadband Wire less — User Manual M900S Rev. C Page 18 Other Key Parameters This section describes the remain der of the parameters listed on th e System Information page. Most of these parameters are the sam e for both APs and SUs. Hardware Version: Hardware versi on is factory-set and cannot be c ...

  • Trango Systems M900S - page 23

    Basic Configuration via Browser Interface Trango Broadband Wire less — User Manual M900S Rev. C Page 19 Site Survey Page The Site Survey page provide s a useful tool for detecti n g and m easuring interfere nce. The radio must be i n Opmode “OF F” in order to use this feature. Enter the num ber of minutes desire d for the survey, and sel ect ...

  • Trango Systems M900S - page 24

    Basic Configuration via CLI Trango Broad band Wireless — Use r Manual M900S Rev C Page 20 Section 5 Basic Configur ation v ia CLI This section covers how to utilize the radio’s CLI interface to establish a working wireless link. In this section t h e most basic se ttings using t he CLI are discu ssed. Topics inclu d e: • Access Point Basic Se ...

  • Trango Systems M900S - page 25

    Basic Configuration via CLI Trango Broad band Wireless — Use r Manual M900S Rev C Page 21 AP SYSTEM INFORMATION PA RAMETERS AND RELATED COMMANDS AP Parameter Description Related CLI Command AP ID This parameter provides a unique num ber for each AP. If Target AP is specified on SU, the SU can only authe n ticate with the specified AP. The default ...

  • Trango Systems M900S - page 26

    Basic Configuration via CLI Trango Broad band Wireless — Use r Manual M900S Rev C Page 22 AP SYSTEM INFORMATION PA RAMETERS AND RELATED COMMANDS AP Parameter Description Related CLI Command MIR Threshol d (Kbps) User specified MIR Threshold. To specify total throughpu t level that the AP will serve only CIR (committed information rate) to associa ...

  • Trango Systems M900S - page 27

    Basic Configuration via CLI Trango Broad band Wireless — Use r Manual M900S Rev C Page 23 AP SYSTEM INFORMATION PA RAMETERS AND RELATED COMMANDS AP Parameter Description Related CLI Command enables/disables the SU t o SU featur e. When SU to SU is turned on, multiple SU’s within the same sector (meaning associated to that AP) can communicate wi ...

  • Trango Systems M900S - page 28

    Basic Configuration via CLI Trango Broad band Wireless — Use r Manual M900S Rev C Page 24 Example: #>sudb cirmir 5 128 256 3000 3000 In this example, SU #5’s CIR downstream was set to 128, and its CIR upstream to 256. MIR upstream and downstream were set to 3000. To change t he default C IR/MIR values, use the following com mand: sudb defaul ...

  • Trango Systems M900S - page 29

    Basic Configuration via CLI Trango Broad band Wireless — Use r Manual M900S Rev C Page 25 ...

  • Trango Systems M900S - page 30

    Basic Configuration via CLI Trango Broad band Wireless — Use r Manual M900S Rev C Page 26 SU SYSTEM INFORMATION PARA ME TERS AND RELATED COMMANDS SU Parameter Description Related CLI Command Device ID MAC Address of the SU N/A Base ID Specifies the cell or cluster t o which the SU belongs. set baseid <baseid> Example: #>Set baseid aa12 T ...

  • Trango Systems M900S - page 31

    Basic Configuration via CLI Trango Broad band Wireless — Use r Manual M900S Rev C Page 27 SU SYSTEM INFORMATION PARA ME TERS AND RELATED COMMANDS SU Parameter Description Related CLI Command polarizati on. antenna [<h | v |e>] Broadcast Packet Filter This software switch (0) enables/disable s the blocking of Ethernet c ontrol packets, excep ...

  • Trango Systems M900S - page 32

    Mounting Hardware Trango Broad band Wireless — Use r Manual M900S Rev C Page 28 Section 6 Mounting Hardware 1 2 3 4 5 Not Supplied ITEM NO. PART NUMBER QTY. 1 Radio 1 2 #10 x 3" Thread ed Rod 4 3# 1 0 K e p s N u t 8 4" V " B r a c k e t 2 5 Mono Pod Mount (Not Supplied) 1 Figure 9: M900S Mounti ng Hardware Assembly ...

  • Trango Systems M900S - page 33

    Mounting Hardware Trango Broad band Wireless — Use r Manual M900S Rev C Page 29 ITEM NO. PART NUMBER QTY. 1 Radio 1 2 #10 x 3" Thread ed Rod 4 3 #10 Keps Nut 8 4" V " B r a c k e t 2 5 Mono Pod Mount (Not Supplied) 1 Alternate Mounting Configuarat ion 1 2 3 4 5 Not Supplied Figure 10: Alternative Mounting ...

  • Trango Systems M900S - page 34

    Mounting Hardware Trango Broad band Wireless — Use r Manual M900S Rev C Page 30 Standard Mounting Alternative Mounting Up/ Down Ti l t 4X M us t B e lo o se n e d fo r Up/ Down Ti l t Up/Down Tilt Figure 11: Articulation for M900S with Mo no Pod Mount (not supplied) Cabling and Grounding Considerations Grounding Example Figure 12: Gr ounding of t ...

  • Trango Systems M900S - page 35

    Mounting Hardware Trango Broad band Wireless — Use r Manual M900S Rev C Page 31 Installation Notes Access to the radio’s RJ-45 Port and LED status lights are purposely located at the bottom of the radio to minimize the risk of water intrusion. Do not mount the radio upside down. The J-Box is not a weatherized device, and must be l oca ted eithe ...

  • Trango Systems M900S - page 36

    Deployment Trango Broad band Wireless — Use r Manual M900S Rev C Page 32 Section 7 Deployment Once you are familiar with t he basic oper ation of the radi os you are rea dy for deploym ent in the field. The de ployment process consists of the following step s: • Site Selection • Site Survey • Channel Planni ng • SU Antenna Alignment • L ...

  • Trango Systems M900S - page 37

    Deployment Trango Broad band Wireless — Use r Manual M900S Rev C Page 33 Example: #> survey 2 v Press [space] then [enter] to stop 880 MHz peak -94 dBm avg -99 dBm 882 MHz peak -94 dBm avg -99 dBm 884 MHz peak -94 dBm avg -99 dBm 886 MHz peak -94 dBm avg -99 dBm 888 MHz peak -94 dBm avg -99 dBm 890 MHz peak -94 dBm avg -98 dBm 892 MHz peak -9 ...

  • Trango Systems M900S - page 38

    Deployment Trango Broad band Wireless — Use r Manual M900S Rev C Page 34 In conjunction with the RSSI command , it is also useful to perform the apsearch command that will tell you wh ich AP is providing an ad equate signal at the location of the SU. AP Search 1. Ensure AP is in Opmode “O n.” 2. Run the apsearch command to verify which AP is ...

  • Trango Systems M900S - page 39

    Deployment Trango Broad band Wireless — Use r Manual M900S Rev C Page 35 3 LED -65 dBm 4 LED -60 dBm Collocation and Ch annel Planning With proper channel plann ing and adherence to installa tion guidelines, multiple M900S APs may co-exist and operate interference-free on the same tower or buildin g. The main cons ideration when collocating APs i ...

  • Trango Systems M900S - page 40

    Deployment Trango Broad band Wireless — Use r Manual M900S Rev C Page 36 In establishing and diagnosing the quality of the link betw een the AP and SU(s), there are a few commands that are especially useful. All of these comm ands are perfor med at the AP. A summary of t h ese commands follows: su Displays the status of all SUs in the AP’s SUDB ...

  • Trango Systems M900S - page 41

    Deployment Trango Broad band Wireless — Use r Manual M900S Rev C Page 37 [ip] 192.168.100.120 [subnet] 255.255.255.0 [gateway] 192.168.100.120 [mac] 00 01 DE 16 E3 7F [hw ver] 0005 [fpga ver] 03121104 [fpga chksum] 75930BDC [fw ver] 1p0a2 [fw chksum] F4658C90 [fw datecode] 04010603 [default channel and antenna] 3 h [active channel and antenna] 3 ...

  • Trango Systems M900S - page 42

    Management Trango Broad band Wireless — Use r Manual M900S Rev C Page 38 The “r” is used in this command to repeat the RF link test repeatedly until the user terminates the test by hitting SPACE ENTER. Example: #> su testrflink 88 r Press [space] then [enter] to stop [len] 1512 [suid] 88 [ 0] ...........[AP Tx] 20 [AP Rx] 20 [SU Rx] 20 [ 1 ...

  • Trango Systems M900S - page 43

    Management Trango Broad band Wireless — Use r Manual M900S Rev C Page 39 Section 8 Management Section Topics: • Radio Manage ment Access using TCP/IP • SU Managem ent from the AP’s com mand set • SNMP Radio Management Access Via TCP/IP The IP Addres s of an M900S radio is for management purposes only. The IP address is n o t used for p ur ...

  • Trango Systems M900S - page 44

    Management Trango Broad band Wireless — Use r Manual M900S Rev C Page 40 Loading Multiple SUs into the SUDB using DLOAD Command To load a full database of SU entries in to the AP’s SUDB, you need to create a subscriber database in ASCII text file format. As sh own below, each row rep res ents all information for one SU. Each column is an inform ...

  • Trango Systems M900S - page 45

    Management Trango Broad band Wireless — Use r Manual M900S Rev C Page 41 The Trango SNMP so lution supports MIB-I I (system only) and th e Trango propr ietary Management Info rmation Base (MIB). The S N MP agent res ides on the AP ONLY. T h e AP gathers healt h, status, and performance statistics from all SUs locally, then responds back to the SN ...

  • Trango Systems M900S - page 46

    Management Trango Broad band Wireless — Use r Manual M900S Rev C Page 42 SNMP Setup Trango Broadb and provides only the MIB portion of the SNM P Management system . The radios act a s individual agents , and it is up t he user to provide an SNM P Manager software from a third party ve ndor. Below is an e xample of the set up process for SNMPc fro ...

  • Trango Systems M900S - page 47

    Trango Broadband Wire less — User Manual M900S Rev. C Page 43 Appendix A Command Set Reference (ro = read only access, rw = read write access) Command Radio Description Access ? AP/SU Display complete list of commands and syntax ro/rw ? <command> AP/SU Display sp ecific command syntax ro/rw antenna AP/SU Display current antenna set ting (h= ...

  • Trango Systems M900S - page 48

    Trango Broadband Wire less — User Manual M900S Rev. C Page 44 Command Radio Description Access (power leveling) pppoeonly SU Display current PPPoE filter setting ro/rw pppoeonly <on | off> SU Change PPPoE filter setting With PPPoE filter set to ON, onl y PPPoE packets will pass Default: off – Pass All Packets rw reboot AP/SU Reboot unit r ...

  • Trango Systems M900S - page 49

    Trango Broadband Wire less — User Manual M900S Rev. C Page 45 Command Radio Description Access 21. TX power 22. Remarks 23. RF TX retry at AP, RF TX retry maxed ou t at AP RF TX retry a t SU, RF TX retry maxed out at SU su ipconfig <s uid> <new IP> <new subnet> <new ga teway> AP Change IP, subnet, gateway for specified SU ...

  • Trango Systems M900S - page 50

    Trango Broadband Wire less — User Manual M900S Rev. C Page 46 Command Radio Description Access targetrssi <dBm, -90..-50> AP Change target RSSI. No te: Target RSS I must be +5 dB more than rfrxth (RFRX Threshold). default = -60 rw tftpd AP/SU display current TFTPD status (status is either on or off) This command will also list any cont en t ...

  • Trango Systems M900S - page 51

    Trango Broadband Wire less — User Manual M900S Rev. C Page 47 Appendix B Specifications All specifications apply to the M900S-AP and M900S-SU, un less otherwise noted. Radio Transmit Specifications Storable Channe ls: 4 memory location s Agility: 906 to 924 MHz in 1 MHz increments Default channels: Channel 1: 906 MHz Channel 2: 912 MHz Channel 3: ...

  • Trango Systems M900S - page 52

    Trango Broadband Wire less — User Manual M900S Rev. C Page 48 Auto-Negotiatio n: Fully supports IEEE802 .3-2002 Sect. 2 Clause 28 Bridging F rame Size: 60 to 1600 by tes Mngmt Fram es: 60 to 1472 by tes (includes PING, TE LNET, TFTP, HTTP) Protection: Bi-directional tran sient vo ltage protecti on diodes on all data lines compliance with: IEC6100 ...

  • Trango Systems M900S - page 53

    Trango Broadband Wire less — User Manual M900S Rev. C Page 49 Eth. Out & DC Out: Shielded RJ-45 Jack Pinout for Et h. Out: Po wer (+) on pins 7+8, ground (-) on pins 4+5 and eth. data o n pins 1,2,3 & 6 Indicators: 2 LEDs to i ndicate powe r and a connecti on to radi o Protection: Resettable fuse for DC input Integrated Antenn a (M900S-SU ...

Fabricant Trango Systems Catégorie Network Router

Les documents que nous recevons du fabricant de l'appareilTrango Systems M900S peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Trango Systems
- manuels d’utilisations M900S
- fiches produit Trango Systems
- dépliants
- ou étiquettes-énergie Trango Systems M900S
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Trango Systems M900S.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Trango Systems M900S, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Trango Systems M900S. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Trango Systems M900S.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Trango Systems M900S, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Trango Systems M900S par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Trango Systems M900S.

Le manuel d’utilisation complet Trango Systems, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Trango Systems M900S - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Trango Systems M900S, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lTrango Systems M900S qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Trango Systems M900S - qui devraient nous aider dans les premières étapes lors de l'utilisation Trango Systems M900S
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Trango Systems M900S
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Trango Systems M900S dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Trango Systems M900S?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Trango Systems M900S, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Trango Systems M900S il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)