Français dropdown-ico

Manuel d’utilisation Chamberlain 2595

32 pages 2.88 mb
Télécharger

Aller à la page of 32

Summary
  • Chamberlain 2595 - page 1

    The Chamberlain Group, Inc. 845 Larch A ven ue Elmhurst, Illinois 60126-1196 www .liftmaster .com GARAGE DOOR OPENER Model 2595 3/4 HP For Residential Use Install on Sectional Doors ONL Y THIS OPERA T OR IS INTENDED FOR USE ONL Y WITH I-BEAM RAILS. ® Owner’s Manual ■ Please read this manual and the enc losed safety materials carefull y! ■ F ...

  • Chamberlain 2595 - page 2

    2 Introduction Pages 2-5 Saf ety symbol and signal word re view ........................2 Preparing your garage door ........................................3 T ools needed ...............................................................3 Planning .....................................................................4 Car ton inv entor y ............ ...

  • Chamberlain 2595 - page 3

    3 To prevent damage to garage door and opener: • AL W A YS disable locks before installing and operating the opener . • ONL Y operate garage door opener at 120V , 60 Hz to avoid malfunction and damage. To prevent possible SERIOUS INJURY OR DEA TH: • AL W A YS call a trained door systems technician if garage door binds, sticks, or is out of ba ...

  • Chamberlain 2595 - page 4

    Safet y Reversin g Sensor Support bracket & fastening hardware is required. See page 11. — — — — — — — — Door Center Header Wall FINISHED CEILING Torsion Spring Extension Spring OR Safety Reversing Sensor Gap between floor and bottom of door must not exceed 1/4" Access Door Wall- mounted Door Control Horizontal and vertical ...

  • Chamberlain 2595 - page 5

    5 Straight Door Arm Section Curved Door Arm Section Safety Labels and Literature Header Bracket U P C E IL IN G MO U N T O N L Y 2 Conductor Bell Wire White & White/Red Light Lens (2) Remote Control Transmitter Visor Clip Door Bracket SECURITY ✚ 3-Channel Remote Control (2) Safety Reversing Sensors (1 Sending Eye and 1 Receiving Eye) with 2-C ...

  • Chamberlain 2595 - page 6

    Washered Bolt 5/16"-18x1/2" Lock Nut 6 ASSEMBL Y STEP 1 Attach the Rail to the Motor Unit T o avoid installation difficulties, do not run the garage door opener until instructed to do so. • Remove the bolt and lock nut from the top of the motor unit. • Place rail onto the bolt mounted on the motor unit and align the back hole with the ...

  • Chamberlain 2595 - page 7

    7 ASSEMBL Y STEP 4 Tighten the Chain • Spin the inner nut and loc k washer down the threaded shaft, aw a y from the trolley . •T o tighten the chain, tur n outer nut in the direction shown. As y ou turn the nut, keep the chain fr om twisting. • When the chain is appro ximately 1/2" abov e the base of the rail at its midpoint, re-tighten ...

  • Chamberlain 2595 - page 8

    8 INST ALLA TION STEP 1 Determine the Header Bracket Location SECTIONAL DOOR ONL Y 1. Close the door and mark the inside vertical centerline of the garage door . 2. Extend the line onto the header w all abov e the door . Y ou can fasten the header bracket within 4 feet of the left or right of the door center only if a torsion spring or center beari ...

  • Chamberlain 2595 - page 9

    9 INST ALLA TION STEP 2 Install the Header Bracket Y ou can attach the header brack et either to the wall abov e the garage door , or to the ceiling. F ollow the instructions which will work best for y our par ticular requirements. Do not install the header brac ket o ver drywall. If installing into masonr y , use concrete anchors (not pr ovided). ...

  • Chamberlain 2595 - page 10

    10 Clevis Pin 5/16"x2-3/4" Ring Fastener INST ALLA TION STEP 3 Attach the Rail to the Header Bracket •P osition the opener on the garage floor below the header brac ket. Use packing material as a protective base . NO TE: If the door spring is in the wa y y ou’ll need help . Hav e someone hold the opener securely on a temporary suppor ...

  • Chamberlain 2595 - page 11

    11 Measure Distance Lag Screws 5/16"-18x1-7/8" Structural Supports Bracket (Not Provided) Lag Screws 5/16"-18x1-7/8" (Not Provided) Bolt 5/16"-18x7/8" Lock Washer 5/16" Nut 5/16"-18 — FINISHED CEILING — Hidden Support Bolt 5/16"-18x7/8" Lock Washer 5/16" Nut 5/16"-18 Bolt 5/16"-18 ...

  • Chamberlain 2595 - page 12

    12 KG 1 3 9 7 5 KG 1 3 9 7 5 INST ALLA TION STEP 6 Install the Door Control Locate door control within sight of the door at a minimum height of 5 f eet where small children cannot reach, and aw a y from moving par ts of the door and door hardware . The installation surface must be smooth and flat. If installing into dr ywall (Figure 1), drill 5/32& ...

  • Chamberlain 2595 - page 13

    Trolley NOTICE Overhand Knot Emergency Release Handle Rope Trolley Release Arm 13 INST ALLA TION STEP 7 Install the Lights • Press the release tabs on both sides of lens. Gently rotate lens back and do wnward until the lens hinge is in the fully open position. Do not remov e the lens. • Install up to a 100 watt maximum light b ulb in each sock ...

  • Chamberlain 2595 - page 14

    14 INST ALLA TION STEP 9 Electrical Requirements To av oid installation difficulties, do not run the opener at this time. To reduce the risk of electric shock, your gar age door opener has a grounding type plug with a third g rounding pin. This plug will only fit into a grounding type outlet. If the plug doesn't fit into the outlet you hav e, ...

  • Chamberlain 2595 - page 15

    15 Invisible Light Beam Protection Area Sensor Beam 6" max. above floor Sensor Beam 6" max. above floor F acing the door fr om inside the garage INST ALLA TION STEP 10 Install The Protector System ® The safety rever sing sensor must be connected and aligned correctly bef ore the garage door opener will move in the do wn direction. IMPORT ...

  • Chamberlain 2595 - page 16

    16 FLOOR MOUNT (RIGHT SIDE) WALL MOUNT (RIGHT SIDE) DOOR TRACK MOUNT (RIGHT SIDE) Indicator light Lens Lip Sensor Bracket Door Track Sensor Bracket Extension Bracket Lens Indicator light Lag Screw 1/4x1-1/2" Inside G arage W all Indicator light Sensor Bracket Lens Extension Bracket Inside G arage W all Lock Nut 1-4"-20 Lock Nut 1-4"- ...

  • Chamberlain 2595 - page 17

    17 Carriage bolt 1/4"-20x1/2" Lens Wing nut Figure 4 MOUNTING AND WIRING THE SAFETY SENSORS • Slide a 1/4"-20x1/2" carriage bolt head into the slot on each sensor . Use wing nuts to fasten sensors to brac kets , with lenses pointing toward each other across the door . Be sure the lens is not obstr ucted by a brac ket e xtensio ...

  • Chamberlain 2595 - page 18

    18 INST ALLA TION STEP 11 Fasten the Door Bracket F ollow instructions which apply to your door type as illustrated belo w or on the f ollowing page. A horizontal reinfor cement brace should be long enough to be secured to two or three vertical supports. A ver tical reinfor cement brace should cover the height of the top panel. Figure 1 shows one p ...

  • Chamberlain 2595 - page 19

    19 INST ALLA TION STEP 12 Connect Door Arm to T rolley SECTIONAL DOORS ONL Y •M ake sure gar age door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolle y . Slide the outer trolley back (a way from the door) about 2" as sho wn in Figures 1, 2 and 3. •F igure 1: – F asten straight door ...

  • Chamberlain 2595 - page 20

    20 ADJUSTMENT STEP 1 Adjust the UP and DOWN T ravel Limits Limit adjustment settings regulate the points at which the door will stop when moving up or do wn. To operate the opener , press the Door Control push bar . Run the opener through a complete trav el cycle. • Does the door open and close completely? • Does the door sta y closed and not r ...

  • Chamberlain 2595 - page 21

    21 ADJUSTMENT STEP 2 Adjust the Force F orce adjustment controls are located on the right side panel of the motor unit. Force adjustment settings regulate the amount of power required to open and close the door . If the f orces are set too light, door trav el may be interrupted by nuisance re versals in the down direction and stops in the up direct ...

  • Chamberlain 2595 - page 22

    22 Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSL Y INJURED or KILLED by a closing garage door . • Safety reversal system MUST be tested every month. • If one control (for ce or travel limits) is adjusted, the other control may also need adjustment. • After ANY adjustments are made ...

  • Chamberlain 2595 - page 23

    OPERA TION Using Y our Garage Door Opener Y our Security ✚ opener and hand-held remote control have been factory-set to a matching code which changes with each use, randomly accessing over 100 billion new codes. Y our opener will operate with up to eight Security ✚ remote controls and one Security ✚ Keyless Entry System. If you purchase a new ...

  • Chamberlain 2595 - page 24

    24 Additional feature when used with the 3-function hand-held remote To control the opener lights: In addition to operating the door , you ma y program the remote to operate the lights. 1. With the door closed, press and hold a small remote button that y ou want to control the light. 2. Press and hold the Light b utton on the door control. 3. While ...

  • Chamberlain 2595 - page 25

    25 CARE OF YOUR OPENER LIMIT AND FORCE ADJUSTMENTS: W eather conditions may cause some minor changes in door operation requiring some re- adjustments, par ticularly dur ing the first year of oper ation. P ages 20 and 21 refer to the limit and f orce adjustments. Only a screwdriv er is required. F ollow the instructions carefully . Repeat the safety ...

  • Chamberlain 2595 - page 26

    26 Having a Problem? (Continued) 6. The garage door opens and closes by itself: • Be sure that all remote control push buttons are off . •R emov e the bell wire from the door control terminals and operate from the remote only . If this solves the prob lem, the door control is faulty (replace), or there is an inter mittent shor t on the wire bet ...

  • Chamberlain 2595 - page 27

    27 *3-Channel Remotes If provided with y our garage door opener , the large b utton is f actor y programmed to operate it. Additional b uttons on an y Security ✚ 3-channel remote or mini-remote can be programmed to operate other Security ✚ garage door openers. To Erase All Codes Fr om Motor Unit Memory To deactivate any unw anted remote, first ...

  • Chamberlain 2595 - page 28

    28 1. Enter a four digit personal identification number (PIN) of y our choice on the ke ypad. Then press and hold ENTER. 2. While holding the ENTER button, press and hold the LIGHT button on the Motion Detecting Door Control. 3. Continue holding the ENTER and LIGHT buttons while y ou press the push bar on the Motion Detecting Door Control (all thre ...

  • Chamberlain 2595 - page 29

    29 7 10 11 5 N O TICE U P C E I L I N G M O U N T O N L Y 8 6 1 4 3 2 9 12 13 L O C K LIG H T 1 3 4 6 5 2 Installation Parts REP AIR P ARTS Rail Assembly Parts KEY P ART NO . NO. DESCRIPTION 1 4A1008 Master link kit 2 41A2780 Chain pulley br ack et 3 41A3489 Complete trolley assemb ly 4 3707CH 7' Rail assembly 3708CH 8' Rail assembly 3710 ...

  • Chamberlain 2595 - page 30

    Motor Unit Assembly Parts 30 DN DN UP UP Brown Wire (Down) Contact LIMIT SWITCH ASSY. Grey Wire Yellow Wire (Up) Contact Center Limit Contact Drive Gear 3 5 4 2 1 16 20 9A 18 6 19 10 13 17 15 12 11 7 7 14 9B 9C 8 8 KEY P ART NO . NO. DESCRIPTION 1 41C5069 Chassis suppor t brack et assy . kit 2 41A4208-2 Chain spreader 3 41A5658 Gear and sprock et a ...

  • Chamberlain 2595 - page 31

    31 L O C K L IG H T C LO S E D O P E N ACCESSORIES 974LM 970LM 995LM 3708CH 1702LM Outside Quick Release: Required for a garage with NO access door . Enables homeowner to open garage door manually from outside by disengaging trolley . 8 Foot Complete Rail: T o allow an 8 foot door to open fully . Remote Light Control: Enables homeowner to turn on a ...

  • Chamberlain 2595 - page 32

    LIFTMASTER GARAGE DOOR OPENER FIVE-YEAR LIMITED W ARRANTY The Chamberlain Group, Inc., (“Seller”) warrants, to the first retail purchaser of this product, for the residence in which this product is originally installed, that it will be free from any defect in materials and/or workmanship for a period of sixty full months from the date of purcha ...

Fabricant Chamberlain Catégorie Garage Door Opener

Les documents que nous recevons du fabricant de l'appareilChamberlain 2595 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Chamberlain
- manuels d’utilisations 2595
- fiches produit Chamberlain
- dépliants
- ou étiquettes-énergie Chamberlain 2595
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Chamberlain 2595.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Chamberlain 2595, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Chamberlain 2595. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Chamberlain 2595.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Chamberlain 2595, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Chamberlain 2595 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Chamberlain 2595.

Le manuel d’utilisation complet Chamberlain, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Chamberlain 2595 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Chamberlain 2595, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lChamberlain 2595 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Chamberlain 2595 - qui devraient nous aider dans les premières étapes lors de l'utilisation Chamberlain 2595
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Chamberlain 2595
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Chamberlain 2595 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Chamberlain 2595?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Chamberlain 2595, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Chamberlain 2595 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)