Français dropdown-ico

Manuel d’utilisation Arrow Fastener VD108-A 697.68618

32 pages 1.11 mb
Télécharger

Aller à la page of 32

Summary
  • Arrow Fastener VD108-A 697.68618 - page 1

    * Size rounded off to the nearest foot BUILDING DIMENSIONS CAUTION: SOME PARTS HAVE SHARP EDGES. CARE MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES TO AVOID A MISHAP. FOR SAFETY SAKE, PLEASE READ SAFETY INFORMATION PROVIDED IN THIS MANUAL BEFORE BEGINNING CONSTRUCTION. WEAR GLOVES WHEN HANDLING METAL PARTS. 708850107 Model No. VD108-A 697.68618 Ow ...

  • Arrow Fastener VD108-A 697.68618 - page 2

    2 Owner's Manual Bef ore beginning constr uction, chec k local building codes regarding f ootings , location and other requirements. Study and understand this owner's manual. Impor tant infor mation and helpful tips will make y our construction easier and more enjo y able . Assembly Instructions: Instructions are supplied in this manual a ...

  • Arrow Fastener VD108-A 697.68618 - page 3

    3 Selecting and Pr eparing Y our Site: Bef ore assembly , y ou will want to decide on a location f or your b uilding. The best location is a le v el area with good drainage . •Allow enough working space for ease of moving parts into position during assembly. Be sure there will be enough space at entrance for doors to open fully and enough space a ...

  • Arrow Fastener VD108-A 697.68618 - page 4

    4 Safety precautions are important to follow throughout the construction of your building. •Care must be taken when handling various pieces of your building since some contain sharp edges. Please wear work gloves, eye protection and long sleeves when assembling or performing any maintenance on your build- ing. •Practice caution with the tools b ...

  • Arrow Fastener VD108-A 697.68618 - page 5

    Finish: F or long lasting finish, per iodically clean and wax the e xterior surface . T ouch- up scratches as soon as you notice them on your unit. Immediately clean the area with a wire brush; wash it and apply touch-up paint per man ufacturer's recommendation. Roof: K eep roof clear of leav es and snow with long handled, soft-bristled broom. ...

  • Arrow Fastener VD108-A 697.68618 - page 6

    6 ACCESSORIES.... A6 WEB * Some drilling required to fit buildings without mid-wall bracing. Model No. SS404 • Makes 8" to 12" (20-30cm) wide shelves in any length. • Brackets, braces, hardware included. Lumber is not included. Model No. SS900-A • Grey color • 3 shelves • Holds up to 85 lbs. (38kg) (even weight distribution) Hea ...

  • Arrow Fastener VD108-A 697.68618 - page 7

    THIS P AGE WA S LEFT BLANK INTENTIONALL Y 7 ...

  • Arrow Fastener VD108-A 697.68618 - page 8

    THIS P AGE WA S LEFT BLANK INTENTIONALL Y 8 ...

  • Arrow Fastener VD108-A 697.68618 - page 9

    The Foundation For Y our Building 9 FRONT (DOOR) FRONT (DOOR) Foundation A09 Note: Finished Slab dimensions, with lumber removed. OPTION 1: ARROW FLOOR FRAME KIT : (Order No. FB109-A or 68385-A) Arrow has the best base for your building in this simple kit. It keeps stored items above the ground. This kit should be used with one of the following: A. ...

  • Arrow Fastener VD108-A 697.68618 - page 10

    It is important that the entire floor frame be anchored after the building is erected. Below are recommended ways of anchoring. Anchoring Down The Building Anchoring A10 Arrow Anchoring Kit: (Model No. AK100 or 68383) Recommended for use with the concrete foundation. Contains: Corner gussets, perimeter clips, hardware, 1/4" masonary drill bit ...

  • Arrow Fastener VD108-A 697.68618 - page 11

    11 Remove from bag of screws and save for the last step 67293 Weather Stripping (1) 5971 Roof Beam Bracket (4) 66382 Lower Door Guide (4) 66242 Door Slide (4) 66183 Roof Trim Cap (2 right & 2 left) 65020 Door Washer (14) (Packed with Screws) 66045 Handle (2) 66646 Washer (216) (6 sheets of 40) 65109 #8-32 Acorn Nut (14) (Packed with Screws) 674 ...

  • Arrow Fastener VD108-A 697.68618 - page 12

    Parts List Y12 12 Assembly P a r t P a r t Quantity Check K e y N o . Number Description i n C arto n List 1 8934 Ramp 1 2 9367 Front Floor Frame 2 3 8936 Rear Floor Frame 2 4 9338 Right Rear Wall Angle 1 5 9366 Door Track 2 6 5287 Splice Post 3 7 9339 Left Rear Wall Angle 1 8 6001 Left Gable 2 9 6000 Right Gable 2 10 9203 Side Floor Frame 4 11 528 ...

  • Arrow Fastener VD108-A 697.68618 - page 13

    13 Assembly by Key No. Y13 28 27 24 25 18 18 23 26 20 12 22 22 13 17 6 16 17 11 9 22 22 22 22 22 22 34 4 19 19 25 16 17 17 8 9 34 35 16 17 10 23 18 8 18 19 19 19 27 28 7 13 16 24 17 17 17 17 17 17 10 10 21 21 21 21 21 21 11 2 3 5 5 31 33 15 30 10 19 6 6 12 31 33 15 29 32 31 31 2 1 32 14 17 11 14 16 16 3 11 ...

  • Arrow Fastener VD108-A 697.68618 - page 14

    The front floor frame is made up of three pieces. The side floor frames and the rear floor frame are made up of two pieces. The holes in these pieces will align when the pieces are positioned with correct amount of overlap. The illustrations below show the proper overall length for the sides, rear and front. Proceed as follows: 1 Place the front fl ...

  • Arrow Fastener VD108-A 697.68618 - page 15

    S tep 2 Y15 15 ● P ar ts Needed F or ● Frame Assemblies The main frame pieces reinforce the walls. These piece will later be in- stalled at the top edge of the side walls and the rear wall. Proceed as follows: 1 Overlap the right and left rear wall angle pieces as shown in the figure and fasten them together with one bolt in the center hole. 2 ...

  • Arrow Fastener VD108-A 697.68618 - page 16

    16 The roof beams join the two gables and support the roof panels. The main roof beam is made up of four pieces overlapped back to back at the cen- ter. The left and right roof beam as- semblies are made up of two pieces. Hint: These pieces are force-fitted, so you may have to press hard to join them together. 1 Place the end of one roof beam insid ...

  • Arrow Fastener VD108-A 697.68618 - page 17

    17 NOTE: Door Track Splice (painted part) S tep 4 A17 ● P ar ts Needed F or ● Door T rack Assembly ● ● ● ● ● 6403 Door Track Splice (1) ● ● ● ● ● 9366 Door Track (2) The door track assembly supports the sliding doors and reinforces the front wall. It is made up of three pieces. 1 Using the door track splice, (painted), join ...

  • Arrow Fastener VD108-A 697.68618 - page 18

    ● ● ● ● ● Front Floor Assembly (1) ● ● ● ● ● Side Floor Assembly (2) ● ● ● ● ● Rear Floor Assembly (1) ● P ar ts Needed For ● Floor Frame S tep 5 G18 The floor frame must be square and level or holes will not align. 18 1 Assemble the four corners of the floor frame using two screws at each corner as shown. At the f ...

  • Arrow Fastener VD108-A 697.68618 - page 19

    1 Position corner posts at the cor- ner of the floor frame as shown. Fas- ten the corner post to the floor frame with two screws. Support the corner posts with stakes or other devices until door jambs are attached. 2 Fasten the door track assembly (holes on top) behind the top of the front corner posts using 1 screw in each corner. See the figure. ...

  • Arrow Fastener VD108-A 697.68618 - page 20

    The door jambs reinforce the door opening and provide an attractive trim. The splice post supports the wall. 1 Position splice post at the center of the rear wall and fasten using 4 bolts and nuts into rear wall angle and 2 screws into rear floor frame. Hint: Measure or count holes to de- termine if post is centered on angle. 2 Fasten splice posts ...

  • Arrow Fastener VD108-A 697.68618 - page 21

    The studs provide a surface for at- taching the siding panels. 1 Following dimensions, measuring from the ends of angles, place a stud between each corner and splice post. Position stud inside top angle and fasten with a screw at the lower hole. 2 Rest bottom tab (large hole) out- side floor frame. Do not fasten tab at this time. Repeat procedure f ...

  • Arrow Fastener VD108-A 697.68618 - page 22

    Each screw in the wall requires a washer. 1 Slide side siding into channels of corner and splice posts, flat edge upward, bottom edge down resting on floor frame. Always follow this pattern. Fasten bottom edge and tab of stud to floor frame using screws. Fasten center to stud with screws. Do not fasten flat edge yet. 2 Install side siding as before ...

  • Arrow Fastener VD108-A 697.68618 - page 23

    1 Slide rear siding into channel of corner and splice posts fastening to rear frame as shown in previous step 9. 2 Install rear siding to complete each section of rear wall. Fasten top center of last siding to rear angle. 3 Slide front siding into channels of corner post and door jamb. This siding is fastened from the inside, using screws into post ...

  • Arrow Fastener VD108-A 697.68618 - page 24

    24 The gables go on top of the front and rear walls to support the roof beams. NOTE The gables are packed nested together and might be mistaken as one piece. Carefully separate them before continuing. 1 Attach the four roof beam brackets to the gables using two bolts, washers and nuts. NOTE Mounting leg of bracket must face toward center of gable a ...

  • Arrow Fastener VD108-A 697.68618 - page 25

    1 Lift and fasten a right and left gable, under angle at corner, to the rear wall angle with screws. Hint: On the rear gable, use a bolt and nut at the overlapping rear wall angle. On the front gable, leave out 2 screws closest to center gable leg. 2 Join the left and right gables together with a gable brace using a bolt in the bottom hole only . 3 ...

  • Arrow Fastener VD108-A 697.68618 - page 26

    1 Spread the two halves of the main roof beam and fasten the roof beam to the gable brace of the front gable. 2 Fasten the other end of the main roof beam to the gable brace of the rear gable. 3 Fasten the single roof beams , small holes on top, as shown using bolts. ● ● ● ● ● Main Roof Beam (1) ● ● ● ● ● Single Roof Beam (2) ? ...

  • Arrow Fastener VD108-A 697.68618 - page 27

    27 S tep 14 Y27 ● P ar ts Needed F or ● Right Roof Panel ● ● ● ● ● 8468 Right Roof Panel (1) Installing the roof panels is best done with a step ladder. Begin installing roof panels at the back right corner of the building. Each screw and bolt in the roof requires a washer. NOTE Measure the building diagonally again and make adjustmen ...

  • Arrow Fastener VD108-A 697.68618 - page 28

    1 Install a left roof panel at the left rear and right front corner of the roof. Install a right roof panel at the left front corner of the roof. 3 Install 2 narrow and 2 wide roof panels in the sequence and posi- tions shown on previous page. Do not fasten the lower end of the panels to the side wall angles at this time. Continue weather stripping ...

  • Arrow Fastener VD108-A 697.68618 - page 29

    1 Install the second ridge cap over- lapping the first ridge cap while in- stalling the remaining roof panels. Continue weather stripping the ridge. 2 Fasten the lower end of the panels to the side wall angles using screws and washers. Use bolts and nuts through wall angle overlaps at the bottom of the panel. ● ● ● ● ● 8486 Ridge Cap (1) ...

  • Arrow Fastener VD108-A 697.68618 - page 30

    30 ● ● ● ● ● 67731 Foam Board (2) ● ● ● ● ● 9934 Right Door (1) ● ● ● ● ● 9935 Left Door (1) ● ● ● ● ● 7667 Horizontal Door Brace (4) ● ● ● ● ● 8641 Vertical Door Brace (2) ● P ar ts Needed F or ● Door Assembly S tep 17 Y30 The steps on this page tell how to assemble the left door. You will per- ...

  • Arrow Fastener VD108-A 697.68618 - page 31

    31 S tep 18 Y31 ● P ar ts Needed F or ● Door Installation & Adjustment ● ● ● ● ● Right Door Assembly (1) ● ● ● ● ● Left Door Assembly (1) 1 From inside the building, put the bottom of the right door assembly (on your left when you are inside the building) behind door jamb into the front frame track. 2 Position the top of ...

  • Arrow Fastener VD108-A 697.68618 - page 32

    SOME FACTS ABOUT RUST Rusting is a natural oxidizing process that occurs when bare metal is exposed to moisture. Problem areas include screw holes, unfinished edges, or where scrapes and nicks occur in the protective coating through normal assembly, handling and use. Identifying these natural rusting problem areas and taking some simple rust protec ...

Fabricant Arrow Fastener Catégorie Outdoor Storage

Les documents que nous recevons du fabricant de l'appareilArrow Fastener VD108-A 697.68618 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Arrow Fastener
- manuels d’utilisations VD108-A 697.68618
- fiches produit Arrow Fastener
- dépliants
- ou étiquettes-énergie Arrow Fastener VD108-A 697.68618
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Arrow Fastener VD108-A 697.68618.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Arrow Fastener VD108-A 697.68618, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Arrow Fastener VD108-A 697.68618. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Arrow Fastener VD108-A 697.68618.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Arrow Fastener VD108-A 697.68618, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Arrow Fastener VD108-A 697.68618 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Arrow Fastener VD108-A 697.68618.

Le manuel d’utilisation complet Arrow Fastener, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Arrow Fastener VD108-A 697.68618 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Arrow Fastener VD108-A 697.68618, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lArrow Fastener VD108-A 697.68618 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Arrow Fastener VD108-A 697.68618 - qui devraient nous aider dans les premières étapes lors de l'utilisation Arrow Fastener VD108-A 697.68618
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Arrow Fastener VD108-A 697.68618
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Arrow Fastener VD108-A 697.68618 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Arrow Fastener VD108-A 697.68618?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Arrow Fastener VD108-A 697.68618, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Arrow Fastener VD108-A 697.68618 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)