Français dropdown-ico

Manuel d’utilisation Cannon 10

28 pages 3.08 mb
Télécharger

Aller à la page of 28

Summary
  • Cannon 10 - page 1

    OWNER’S MANU AL NOTE: Do not return your CANNON® Do wnrigger to your retailer. Your retailer is not authorized to repair or replace t his unit. You may obtain service b y: • calling CANNON® at 1-800-2 27-6433; • returning your do wnrigger to the Factor y Service Center; • sending or taking your d ownrigger to any CA NNON® Authorized Serv ...

  • Cannon 10 - page 2

    2 Parts Description 1. Reel This is used to spool the cable, available in length s ranging from 1 50 to 400 feet. 2. Boom This is used to extend the weight out from the body of the downrigger and has a pulley fixed to its end. Boom lengths range from 24 to 53 inches. 3. Swivel Head This relays the cable at the end of the boom to lower the wei ght. ...

  • Cannon 10 - page 3

    3 Downrigger Mounting on Boats A downrigger should be mounted where ever it is easy to operate and observe. You want to be able to see your fishing rod and to react quickly. So, choosing a good spot to mount your downrigger on your boat is 99% of the job. Due to the great variety of boats available, mounting your downrigger can be a dilemma. Having ...

  • Cannon 10 - page 4

    4 Side Rail Mounting Side/Rail mounts can be mounted to a welded T-section. It can also be used at the two rail section butt joint. In both installations it is recommended to use a non-slip material, such as rubber or a thin wood sheet, between metal surfaces. You can also use these for mounting to a very narrow side gunwale. There is a plate provi ...

  • Cannon 10 - page 5

    5 MOUNTING & SETUP Outboard Fa cing Stern Facing Rear or Stern Note Locking Slots in Base Side or Gunwale Decks up to 7/16" Thick Base Wellnuts Decks Thicker Than 7/16" Washer, Lock Washer, and 1/4-20 Hex Nut Base Inst alling the Base on Y our Boat Decks up to 7/16" thick Where access to the underside of the deck is not available ...

  • Cannon 10 - page 6

    6 Decks thinner than 1/4" Use a Cannon Deck Plate to prevent deflection and add stability to decks thinner than 1/4". Use the deck plate as a template to mark the hole locations. If access to the underside of the deck is not available, the deck plate can be mounted using screws and wellnuts. Drill 1/2" holes. Use four 1/4”-20 x 2&q ...

  • Cannon 10 - page 7

    7 Clamps Standard 24" Boom #8 x 5/8" Screw (1) #4 x 1/2" Screws (2) The 3/4"-Long Phillips Screw Must Engage Hole in Boom Setting Up Y our Downrigger Attaching the Boom Telescopic Boom The intermediate section of the telescopic boom must be extended approximately 5" before the boom locking screw can engage the hole in the b ...

  • Cannon 10 - page 8

    8 Attaching the crank handle Thrust Bearing Spring Races Crank Handle Att aching the Crank Handle Assembly Make sure the thrust bearing is sandwiched between its two races. The thrust bearing spring should be oriented where the narrow end is toward the bearing. Slide the bearing with races and spring over the ratchet shaft. Then, carefully thread t ...

  • Cannon 10 - page 9

    9 T erminating the Downrigger Cable Cannon Uni-Release The Cannon Uni-Release attaches directly to the downrigger weight. Attach fishing line to the clip at the end of the release, and then click through a series of increasing tension settings. The release can be used with any test line on salt or fresh water and may be adjusted from 2 to 22 pounds ...

  • Cannon 10 - page 10

    10 CAUTION: This rod holder is intended for use of up to 30 lb. test line only, and is not recommended for use with any tackle IGFA rated higher than 30 lb. A safety strap (not included) is recommended for all applications. The rod holder assembly is not warranted when used with tackle above 30 lbs. Equipment placed in the rod holders and the loss ...

  • Cannon 10 - page 11

    11 Operating Y our Downrigger After mounting the Cannon downrigger to your boat, release some line from your rod and reel so that the lure is anywhere from 5 to 100 feet behind the boat. This is called drop back. Attach the fishing line firmly into the line release. Lower the weight to the desired depth as indicated on the depth meter. Place the fi ...

  • Cannon 10 - page 12

    12 Blowback Blowback Simply stated, blowback is what happens to the downrigger weight when you pull it through the water behind your boat. As your speed increases, so does the horizontal distance between the weight and your downrigger. The faster you go, the farther the weight is behind you. The farther the weight is behind you, the shallower the w ...

  • Cannon 10 - page 13

    13 Adjusting the Depth Meter The Cannon Depth Meter provides non-slip accuracy, plus easy resetting. To reset, just slide the meter away from the reel until the gears are disengaged. Spin meter gear to change setting. NOTE: Actual fishing depth may vary from depth shown on meter due to trolling speed and weight of cannon ball. (See "Blowback&q ...

  • Cannon 10 - page 14

    14 TROLLING TIPS T en Good T r olling Tip s 1) Test your lures over the boat side before sending them down and back. Do this to make sure the lure wiggles and wobbles properly without going belly up or wandering off. Some lures can be adjusted, fine tuned actually, to impart maximum action. For example, a slight bend in the tail of a spoon or twist ...

  • Cannon 10 - page 15

    15 CANNON® LIMITED W ARRANTY Johnson Outdoors Inc. warrants to the original purchaser that if the accompanying product (see ex clusions below) proves to be defective in material or workmans hip within the following warranty periods, Johnson Outdoors Inc. will, at its option, either repair or replace same without charge (but no cash refunds will be ...

  • Cannon 10 - page 16

    16 For a current list of aut horized Cannon Service Center s, including those ou tside of the US and Canada, please see our web page at www.cannondow nriggers.com . All CANNON Downriggers are covered by US Pat.D-269, 9 92. Copyri ght 2006 Johnson Outdoors, In c. All rights reserved. Conforms t o 89/336/ EEC (EMC) under standards EN 55022A, EN 50082 ...

  • Cannon 10 - page 17

    TM UNI-TROLL 10 1901100 Form No. 3394905 Rev 12/06 ...

  • Cannon 10 - page 18

    1 3330002 FRAME - UNI-TROLL 29 3321001 COVER - CLUTCH, ROUND (LEXAN) 57 2371712 WASHER - 9/32" FLAT [4.EA] 2 3327004 DECAL - NOSE, UNI-TROLL 30 9250003 PIN - DOWEL 3/16" x 7/8" - RATCHET 58 9100100 TERMINATOR 3 9040040 HOOK - 1/4" - 20 ROLLED 31 9400070 SPRING - DOG RATCHET 59 9100101 TERMINATOR CUSHION 4 2263102 NUT - HEX 1/4&q ...

  • Cannon 10 - page 19

    TM UNI-TROLL 10 METRIC 1901101 Form No. 3394913 Rev 12/06 ...

  • Cannon 10 - page 20

    1 3330002 FRAME - UNI-TROLL 29 0902000 CRANK HANDLE - UNI-TROLL 57 2263102 NUT - HEX 1/4"-20 [4.EA] 2 3327004 DECAL - NOSE, UNI-TROLL 30 3321001 COVER - CLUTCH, ROUND (LEXAN) 58 2371712 WASHER - 9/32" FLAT [4.EA] 3 9040040 HOOK - 1/4" - 20 ROLLED 31 9250003 PIN - DOWEL 3/16" x 7/8" - RATCHET 59 9100100 TERMINATOR 4 2263102 ...

  • Cannon 10 - page 21

    TM UNI-TROLL 10 TS 1901110 Form No. 3394914 Rev 12/06 ...

  • Cannon 10 - page 22

    1 3392506 FRAME - UNI-TROLL, WHITE 29 3390202 COVER - CLUTCH, ROUND, WHITE (LEXAN) 57 2371712 WASHER - 9/32" FLAT [4.EA] 2 3327004 DECAL - NOSE, UNI-TROLL 30 9250003 PIN - DOWEL 3/16" x 7/8" - RATCHET 58 9100100 TERMINATOR 3 9040040 HOOK - 1/4" - 20 ROLLED 31 9400070 SPRING - DOG RATCHET 59 9100101 TERMINATOR CUSHION 4 2263102 N ...

  • Cannon 10 - page 23

    TM UNI-TROLL 10 TS/E 1901111 Form No. 3394919 Rev 12/06 ...

  • Cannon 10 - page 24

    1 3392506 FRAME - UNI-TROLL, WHITE 29 0902000 CRANK HANDLE - UNI-TROLL 57 2263102 NUT - HEX 1/4"-20 [4.EA] 2 3327004 DECAL - NOSE, UNI-TROLL 30 3390202 COVER - CLUTCH, ROUND, WHITE (LEXAN) 58 2371712 WASHER - 9/32" FLAT [4.EA] 3 9040040 HOOK - 1/4" - 20 ROLLED 31 9250003 PIN - DOWEL 3/16" x 7/8" - RATCHET 59 9100100 TERMINA ...

  • Cannon 10 - page 25

    TM UNI-TROLL 5 1901105 Form No. 3394915 Rev 12/06 ...

  • Cannon 10 - page 26

    1 3330002 FRAME - UNI-TROLL 23 0467694 BRAKE PLATE - RATCHET 45 2277002 >UNIVERSAL LINE RELEASE 2 3327004 DECAL - NOSE, UNI-TROLL 24 1000904 SHAFT - RATCHET - UNI-TROLL 46 3992300 SWIVEL HEAD ASSEMBLY 3 9040040 HOOK - 1/4" - 20 ROLLED 25 9010310 WASHER - THRUST [2.EA] 47 0267001 ► SIDE PLATE (RH) 4 2263102 NUT - HEX 1/4"-20 26 901028 ...

  • Cannon 10 - page 27

    TM UNI-TROLL 5 METRIC 1901106 Form No. 3394916 Rev 12/16 ...

  • Cannon 10 - page 28

    1 3330002 FRAME - UNI-TROLL 23 1264670 CLUTCH PAD 45 9430160 >WASHER - STAR 5/16" 2 3327004 DECAL - NOSE, UNI-TROLL 24 0467694 BRAKE PLATE - RATCHET 46 2277002 >UNIVERSAL LINE RELEASE 3 9040040 HOOK - 1/4" - 20 ROLLED 25 1000904 SHAFT - RATCHET - UNI-TROLL 47 3992300 SWIVEL HEAD ASSEMBLY 4 2263102 NUT - HEX 1/4"-20 26 9010310 W ...

Fabricant Cannon Catégorie Fishing Equipment

Les documents que nous recevons du fabricant de l'appareilCannon 10 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Cannon
- manuels d’utilisations 10
- fiches produit Cannon
- dépliants
- ou étiquettes-énergie Cannon 10
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Cannon 10.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Cannon 10, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Cannon 10. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Cannon 10.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Cannon 10, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Cannon 10 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Cannon 10.

Le manuel d’utilisation complet Cannon, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Cannon 10 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Cannon 10, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lCannon 10 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Cannon 10 - qui devraient nous aider dans les premières étapes lors de l'utilisation Cannon 10
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Cannon 10
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Cannon 10 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Cannon 10?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Cannon 10, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Cannon 10 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)