-
Chicago Electric Model 90891 - page 1
10” COMPOUND SLIDE MITER SA W Model 90891 SET UP AND OPERA TING INSTRUCTIONS Diagrams within this manual may not be drawn proportionally . Due to continuing improvements, actual product may differ slightly from the product described herein. Distributed exclusively by Harbor Freight T ools ® . 3491 Mission Oaks Blvd., Camarillo, CA 9301 1 Visit o ...
-
Chicago Electric Model 90891 - page 2
Page 2 SKU 90891 For technical questions, please call 1-800-444-3353. REV 05i, 07h SPECIFICA TIONS Electrical Requirements 120 V / 60 Hz / 4600 RPM 10.8 A Input Working Amperage (with load) 1-3/4 HP Motor / Single Phase 2-Prong Power Plug Double Insulated Motor w/ External Access Brushes Arbor Diameter 5/8” (0.625”) Positive Stops 0°, 15°, 22 ...
-
Chicago Electric Model 90891 - page 3
Page 3 SKU 90891 For technical questions, please call 1-800-444-3353. Do not operate power tools in explosive atmospheres, such as in the pres- ence of ammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes. Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause yo ...
-
Chicago Electric Model 90891 - page 4
Page 4 SKU 90891 For technical questions, please call 1-800-444-3353. Dress properly . Do not wear loose clothing or jewelry . Contain long hair . Keep your hair , clothing, and gloves away from moving parts. Loose clothes, jewelry , or long hair can be caught in moving parts. A void accidental starting. Be sure the Power Switch is off before plugg ...
-
Chicago Electric Model 90891 - page 5
Page 5 SKU 90891 For technical questions, please call 1-800-444-3353. Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may become hazardous when used on another tool. SER VICE T ool service must be performed only by qualied repair personnel. Service or maintenance perform ...
-
Chicago Electric Model 90891 - page 6
Page 6 SKU 90891 For technical questions, please call 1-800-444-3353. When replacing the Saw Blade, make sure the new Saw Blade has a diam- eter of 10”, has an RPM rating of at least 4600, and has an arbor hole of 5/8” diameter . T o avoid accidental injury , always wear heavy duty work gloves when changing a Saw Blade. Before using the Miter S ...
-
Chicago Electric Model 90891 - page 7
Page 7 SKU 90891 For technical questions, please call 1-800-444-3353. job better and more safely at the rate for which it was intended. Do not modify this product, and do not use this product for a purpose for which it was not in- tended. Always turn off the Miter Saw and unplug the Power Cord from its electrical outlet before changing accessories ...
-
Chicago Electric Model 90891 - page 8
Page 8 SKU 90891 For technical questions, please call 1-800-444-3353. Grounded T ools: T ools with Three Prong Plugs T ools marked with “Grounding Required” have a three wire cord and three prong grounding plug. The plug must be connected to a properly grounded outlet. If the tool should electrically malfunction or break down, grounding provide ...
-
Chicago Electric Model 90891 - page 9
Page 9 SKU 90891 For technical questions, please call 1-800-444-3353. The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a 14 gauge cord can carry a higher current than a 16 gauge cord. (See T able A.) When using more than one extension cord to make up the total length, make sure each cord contains at least ...
-
Chicago Electric Model 90891 - page 10
Page 10 SKU 90891 For technical questions, please call 1-800-444-3353. UNP ACKING When unpacking, check to make sure all the parts shown on the Parts Lists on pages 22 and 23 are included. If any parts are missing or broken, please call Harbor Freight T ools at the number shown on the cover of this manual as soon as possible. ASSEMBL Y AND FUNCTION ...
-
Chicago Electric Model 90891 - page 11
Page 1 1 SKU 90891 For technical questions, please call 1-800-444-3353. BAFFLE PLA TE (151) HOLDER (149) WING SCREW (148) ADJUSTING KNOB (102) GUIDE FENCE (105) WING SCREW (97) FIGURE E A workpiece Clamp Assembly (95, 96, 97, 98, 99, 100, 101, 102) can be installed by inserting the Assembly into the hole located in the Guide Fence (105). Once inser ...
-
Chicago Electric Model 90891 - page 12
Page 12 SKU 90891 For technical questions, please call 1-800-444-3353. 1/4” MOUNTING HOLE 1/4” MOUNTING HOLE FIGURE F FRONT COVER WITH SUPPORT LEG (1 17) Use two C-clamps (not included) to secure the back side of the Miter Saw to the table/workbench. T o Remove/Install A Saw Blade: W ARNING! Prior to performing this procedure, make sure the Mit ...
-
Chicago Electric Model 90891 - page 13
Page 13 SKU 90891 For technical questions, please call 1-800-444-3353. FLA T HEAD SCREW (60) CENTER COVER (55) FIGURE H SAFETY COVER (58) Remove the Flat Head Screw (60) and Center Cover (55). (See Figure H.) SHAFT LOCK (1) FIGURE I HANDLE COVER (40) SAFETY COVER (58) SAFETY BUTT ON (16) SWITCH LEVER (25) Press in and hold the Shaft Lock (1) to kee ...
-
Chicago Electric Model 90891 - page 14
Page 14 SKU 90891 For technical questions, please call 1-800-444-3353. HEX SOCKET WRENCH (150) HEX FLANGE HEAD BOL T (61) FLANGE (52) HEX FLANGE HEAD BOL T (61) FLANGE (52) FIGURE J BLADE CASE (43) ARROW SA W BLADE (51) ARROW FIGURE K Remove the old Saw Blade (51). Then mount the new Saw Blade on the Spindle (35), making sure the arrow direction on ...
-
Chicago Electric Model 90891 - page 15
Page 15 SKU 90891 For technical questions, please call 1-800-444-3353. SA W BLADE (51) HEX FLANGE HEAD BOL T (61) FLANGE (52) SPINDLE (35) INNER FLANGE (65) FIGURE L Insert the Flange (52) onto the Spindle (35) and against the Saw Blade (51). NOTE: Make sure the larger diameter side of the Flange is against the Saw Blade. (See Figure L.) Press in a ...
-
Chicago Electric Model 90891 - page 16
Page 16 SKU 90891 For technical questions, please call 1-800-444-3353. The Power Switch: Note: The Miter Saw can be disabled for safety purposes by removing the Safety But- ton (16). Make sure to store the Safety Button in a safe place, and do not lose it. The Miter Saw cannot be started without the Safety Button in place. (See Figure I.) Before pl ...
-
Chicago Electric Model 90891 - page 17
Page 17 SKU 90891 For technical questions, please call 1-800-444-3353. KERF BOARD (1 14) HEX HEAD BOL T (71) SA W BLADE (51) MOTOR HOUSING (26) TURN BASE (125) FIGURE M Push the Miter Saw’s Motor Housing (26) forward as far as it will go. Notice whether the edge of the Saw Blade (51) passes completely through the Kerf Board (1 14). (See Figure M. ...
-
Chicago Electric Model 90891 - page 18
Page 18 SKU 90891 For technical questions, please call 1-800-444-3353. T o Adjust The Miter Angle: W ARNING! Prior to performing this procedure, make sure the Power Cord of the Miter Saw is unplugged from its electrical outlet. F ASTEN KNOB (104) SCALE PLA TE (141) TURN BASE (125) GUIDE FENCE (105) FIGURE N Knob (74) The miter angle of a cut may be ...
-
Chicago Electric Model 90891 - page 19
Page 19 SKU 90891 For technical questions, please call 1-800-444-3353. T o Adjust The Support Screw: The Support Screw (138) can be adjusted by turning it clockwise to lengthen it or by turning it counter- clockwise to shorten it. It should be adjusted so that it rests just above the surface of the table or bench the saw is mounted on. 1. 2. T o Ad ...
-
Chicago Electric Model 90891 - page 20
Page 20 SKU 90891 For technical questions, please call 1-800-444-3353. OPERA TION Make sure the Power Cord of the Miter Saw is unplugged from its electri- cal outlet. Then, if necessary , make adjustments to the workpiece Holder (149), Bafe Plate (151), cutting depth, and miter angle and/or bevel angle. Raise the Motor Housing (26) to its full ? ...
-
Chicago Electric Model 90891 - page 21
Page 21 SKU 90891 For technical questions, please call 1-800-444-3353. INSPECTION, MAINTENANCE, AND CLEANING W ARNING! Always make sure the Switch Lever (25) is in its “OFF” position, and unplug the Power Cord from its 120 volt electrical outlet before performing any inspection, adjustments, maintenance, or cleaning. Before each use, inspect th ...
-
Chicago Electric Model 90891 - page 22
Page 22 SKU 90891 For technical questions, please call 1-800-444-3353. REV 05b P ARTS LIST T orsion Spring Assy . * * Includes: #57 Spindle Sleeve and #58 Safety Cover . (Note: Customer must save old brass sleeve from old Safety Cover and use it when installing new #56 T orsion Spring Assembly). ...
-
Chicago Electric Model 90891 - page 23
Page 23 SKU 90891 For technical questions, please call 1-800-444-3353. P ARTS LIST - CONTINUED REV 04d ...
-
Chicago Electric Model 90891 - page 24
Page 24 SKU 90891 For technical questions, please call 1-800-444-3353. Note: Some parts are listed and shown for illustration purposes only , and are not avail- able individually as replacement parts. ASSEMBL Y DIAGRAM 1 2 3 4 5 6 7 8 9 10 1 1 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 4 ...
-
Chicago Electric Model 90891 - page 25
Page 25 SKU 90891 For technical questions, please call 1-800-444-3353. ASSEMBL Y DIAGRAM - CONTINUED REV 04d 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 1 10 1 1 1 1 12 1 13 1 14 1 15 1 16 1 17 1 18 1 19 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 154 141 142 143 144 145 14 ...
Avez-vous une question à propos de Chicago Electric Model 90891?
Utiliser le formulaire ci-dessous
Si vous n’avez pas résolu votre problème avec Chicago Electric Model 90891, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Chicago Electric Model 90891 il est probable qu’il a envie de partager la façon de le résoudre.