Français dropdown-ico

Manuel d’utilisation Kenwood TK-8150

23 pages 0.45 mb
Télécharger

Aller à la page of 23

Summary
  • Kenwood TK-8150 - page 1

    TK-7150 INSTRUCTION MANUAL VHF FM TRANSCEIVER © B62-1619-10 (K) 09 08 07 06 05 04 03 02 01 TK-8150 UHF FM TRANSCEIVER SCN SP OP OS AB MON CALL ...

  • Kenwood TK-8150 - page 2

    T HANK Y OU We are grateful you chose KENWOOD for your personal mobile applications. W e believe this easy-to-use transceiver will provide dependable communications to keep personnel operating at peak efficiency . KENWOOD transceivers incorporate the latest in advanced technology . As a result, we feel strongly that you will be pleased with the qua ...

  • Kenwood TK-8150 - page 3

    i ◆ Government law prohibits the operation of unlicensed radio transmitters within the territories under government control. ◆ Illegal operation is punishable by fine or imprisonment or both. ◆ Refer service to qualified technicians only . Safety: It is important that the operator is aware of, and understands, hazards common to the operation ...

  • Kenwood TK-8150 - page 4

    ii CONTENTS UNP ACKING AND CHECKING EQUIPMENT ................................................ 1 S UPPLIED A CCESSORIES ................................................................................. 1 PREP ARA TION ............................................................................................... 2 T OOLS R EQUIRED ................. ...

  • Kenwood TK-8150 - page 5

    1 UNP ACKING AND CHECKING EQUIPMENT Note: The following unpacking instructions are for use by your KENWOOD dealer , an authorized KENWOOD service facility , or the factory . Carefully unpack the transceiver . We recommend that you identify the items listed in the following table before discarding the packing material. If any items are missing or ha ...

  • Kenwood TK-8150 - page 6

    2 V arious electronic equipment in your vehicle may malfunction if they are not properly protected from the radio frequency energy which is present while transmitting. Electronic fuel injection, anti-skid braking, and cruise control systems are typical examples of equipment that may malfunction. If your vehicle contains such equipment, consult the ...

  • Kenwood TK-8150 - page 7

    3 I NST ALLING THE T RANSCEIVER For passenger safety , install the transceiver securely , using the supplied mounting bracket, so the transceiver will not break loose in the event of a collision. 1 Mark the position of the holes in the dash by using the mounting bracket as a template. Drill the holes, then attach the mounting bracket using the supp ...

  • Kenwood TK-8150 - page 8

    4 ORIENT A TION F RONT P ANEL AND M ICROPHONE q q q q q V olume Control Rotate to adjust the volume level. Clockwise increases the volume and counterclockwise decreases the volume. w w w w w Display (See page 5.) e e e e e Selector Rotate to select a zone or channel/group ID. Clockwise increases the zone / channel/group ID and counterclockwise decr ...

  • Kenwood TK-8150 - page 9

    5 !0 !0 !0 !0 !0 PF5 Key Press this key to activate its programmable auxiliary function {page 7}. The default setting is None. !1 !1 !1 !1 !1 PF6 Key Press this key to activate its programmable auxiliary function {page 7}. The default setting is None. !2 !2 !2 !2 !2 TX / BUSY LEDs The TX LED lights red while transmitting. In Conventional Groups, th ...

  • Kenwood TK-8150 - page 10

    6 R EAR P ANEL 6-pin connector (for accessories) Power input connector Antenna connector 25-pin connector (for accessories) ...

  • Kenwood TK-8150 - page 11

    7 PROGRAMMABLE AUXILIARY FUNCTIONS Keys y to !1 {pages 4 and 5} can be programmed with the auxiliary functions listed below . The keys can only be programmed with functions, depending on whether you are using a Conventional Group or a T runking System. Please contact your dealer for further details on these functions. • Auto T elephone • AUX A ...

  • Kenwood TK-8150 - page 12

    8 BASIC OPERA TIONS O PERA TION O VERVIEW Y our dealer can program your transceiver with T runking Systems and Conventional Groups. T runking Systems can handle 32 zones with up to 250 group IDs. Conventional Groups can handle up to 128 zones with up to 128 channels. The transceiver can handle a maximum combination of 128 zones in T runking Systems ...

  • Kenwood TK-8150 - page 13

    9 TRUNKING ZONES P LACING A D ISP A TCH C ALL 1 Select the desired trunking zone and a group ID. 2 Press and hold the PTT switch. 3 If the “Clear to T alk” tone sounds, communication is possible; start speaking into the microphone. Release the PTT switch to receive. • For best sound quality at the receiving station, hold the microphone approx ...

  • Kenwood TK-8150 - page 14

    10 CONVENTIONAL ZONES T RANSMITTING 1 Select the desired conventional zone and a channel. • Make sure the channel is not in use. When a channel is in use, the BUSY (green) LED will light. 2 Press and hold the PTT switch, then speak into the microphone in your normal speaking voice. • For best sound quality at the receiving station, hold the mic ...

  • Kenwood TK-8150 - page 15

    11 SCAN To activate the Scan function, press the key programmed as Scan . • The SCN icon lights and “-SCAN-” appears on the display . To stop scanning, press the Scan key again. • The transceiver returns to the channel that was selected before Scan started. S CAN T YPES There are three types of scans available: Single Zone Scan, Multi Zone ...

  • Kenwood TK-8150 - page 16

    12 DTMF CALLS Note: To make DTMF calls, you must have an optional microphone with a DTMF keypad. M ANUAL D IALLING Press and hold the PTT switch, then enter the digits on the microphone keypad. •Y ou can enter the digits 0 ~ 9 , , and # . • If programmed by your dealer , you do not need to continuously hold the PTT switch; the transceiver will ...

  • Kenwood TK-8150 - page 17

    13 C LEARING S TORED DTMF N UMBERS 1 Press and hold the microphone # key for 1 second. • “D” appears on the display . 2 P ress the # key again. • “D–CLEAR” appears on the display . •T o cancel the process, press any key other than 0 ~ 9 . 3 Enter the desired memory location number (01 ~ 32). R EDIALLING 1 Press and hold the micropho ...

  • Kenwood TK-8150 - page 18

    14 FleetSync™: ALPHANUMERIC TWO-W A Y PAGING FUNCTION FleetSync™ is an Alphanumeric T wo-way Paging Function, and is a protocol owned by KENWOOD Corporation. FleetSync™ enables a variety of paging functions on your transceiver , some of which depend on dealer programming. Y our dealer can set up either FleetSync™ or FleetSync™ II on your ...

  • Kenwood TK-8150 - page 19

    15 O PTIONAL F EA TURES Short Messages: Received short messages (maximum of 48 characters) are displayed the same as Status messages {page 16}, however only 4 short messages can be stored in the stack memory . “M” (Message) and the message number appear with the message. GPS Report: If an external GPS receiver (NMEA-0183 format) is installed on ...

  • Kenwood TK-8150 - page 20

    16 ■ Identification Codes An ID code is a combination of a 3-digit Fleet number and a 4-digit ID number . Each transceiver must have its own Fleet and ID number . • Enter a Fleet number (100 ~ 349) to make a group call. • Enter an ID number (1000 ~ 4999) to make an individual call in your fleet. • Enter a Fleet number followed by an ID numb ...

  • Kenwood TK-8150 - page 21

    17 ■ Receiving The mail icon ( ) will flash and a calling ID or text message will appear when a Status call is received. • The display alternates between the caller ID and the message. Press any key to return to Normal Operation Mode. ■ Reviewing Messages in the Stack Memory 1 Press and hold the key programmed as Message Mode for more than 1 ...

  • Kenwood TK-8150 - page 22

    18 ADV ANCED OPERA TIONS T IME - OUT T IMER (TOT) The T ime-out T imer prevents any single caller from using a channel for an extended period of time. If you continuously transmit for a period of time that exceeds the programmed time, the transceiver will stop transmitting and an alert tone will sound. T o stop the tone, release the PTT switch. Y o ...

  • Kenwood TK-8150 - page 23

    19 E MERGENCY O PERA TION Press and hold the key programmed as Emergency to enter Emergency Operation. • The duration you need to hold the key depends on how your transceiver has been set up. • The transceiver will switch to the pre-programmed emergency channel/ group ID. While in Emergency Operation, the transceiver will perform the emergency ...

Fabricant Kenwood Catégorie Marine Radio

Les documents que nous recevons du fabricant de l'appareilKenwood TK-8150 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Kenwood
- manuels d’utilisations TK-8150
- fiches produit Kenwood
- dépliants
- ou étiquettes-énergie Kenwood TK-8150
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Kenwood TK-8150.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Kenwood TK-8150, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Kenwood TK-8150. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Kenwood TK-8150.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Kenwood TK-8150, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Kenwood TK-8150 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Kenwood TK-8150.

Le manuel d’utilisation complet Kenwood, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Kenwood TK-8150 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Kenwood TK-8150, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lKenwood TK-8150 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Kenwood TK-8150 - qui devraient nous aider dans les premières étapes lors de l'utilisation Kenwood TK-8150
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Kenwood TK-8150
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Kenwood TK-8150 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Kenwood TK-8150?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Kenwood TK-8150, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Kenwood TK-8150 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)